Full shutdown: 29 MA
Sleep mode: 31 MA (practical. Same)

At the time of download: up to 0.55 A
In CPU mode 10-20%: 0.26 A
View heavy video (jellyfish): 0.37 A
CPU Throttling Test (CPU 100%): 0.43 A
When the USB 3.0 CPU flash drive is inserted 10-20%: 0.4..0.5 A (of course, depends on the flash drive model)

None under no modes have observed an increase in current more than 0.7 A (except for the power of external HDD).

The results of measurement of the output voltage mowed me.
Without connecting boxing: 5,29 V
In peace mode: 5.27 V
Inserted USB 3.0 USB flash drive: 5.27 V
CPU Throttling Test: 5.26 V (!)
Inserted USB 3.0 HDD disk with power through USB boxing seagate 2 TB (current consumed to 0.6 a): 5.25 V (!!!)

That is, there are practically no voltage drawdowns at maximum load.
Variable voltage pulsation: 2 mV under load (twoMillivolt). I could not believe, checked with different devices.

Measurement mode: Firmware Last June in Vasily version, MicroSD Map 32 GB is constantly inserted and the G20S aircraft sensor.

Post has been editeddiman19 - 11.11.19, 18:06

Indeed, 3.8m resistor, goes to the first leg of the chip. Under it is the inscription R8.

But there is no question of a fall in the floor-volt, as it turned out. Pulsations are not noticeable practically.
I wanted to replace one of the electrolytes at the exit to 1500 UF, but after the measurements decided that there was no point. It was limited to the fact that in parallel, the exit was put in Ceramic 0.1 UF.

LoGatto,
I didn't suffer immediately put on the entrance of the 39UFX400V Rubycon, the throttle 4.7 ОјH, at the yield 2pcs 1000 UFX10V at the mnu of the animal a bit of another x96max, insured. Here's thinking something about whether to buyhttps://ru.aliexpress.com/item/32954801420.htmlstory...
In the housing to shove shut;)

Access to the Droid Settings box settings (from the right) from the Squarehome launcher

For those who can handle system text files.
For example, with Root Explorer.

1. in Squarehome createempty "Tile group" (without choosing an application, immediately press OK).
2. In Root Explorer in root, you pre-press the "R / W Right" button.
3. In Root Explorer we go to /data/data/com.ss.squarehome2/files/layout/
4. There findthe last time The file, it must be the size of 2 bytes (file names there in style 12C264A8C4C).
5. Open it for editing (click on the file, select "Text Editor")
The editor appears text, this is: [] (carefully! If the text is different, you confused the file).
6. We delete this text.
7. We replace it with this line:

Just copy the above line and paste into the file.
8. Save the modified file (three points ->Save and exit).

In the box, edit is uncomfortable, instead of the items 5-8, I copied the file to the computer and edited there. Then replaced the existing file on the box.

9. Restart boxing.

After that, in the tiles group there should be a file with a gear in a circle.
You can drag it from there to the main screen Squarehome.

Of courseat one's own risk.

Post has been editeddiman19 - 17.11.19, 21:14

LoGatto , thank. You still need a tile for cleaning RAM into one click. Preferably with the help of an already built-in clever ...

The more climb into system files, the greater the likelihood of overpaying the console. On the prescribing Amkodek, many have grown, who in the subject will understand.
Advanced settings can be displayed a couple of times by pressing the mouse. As well as regular settings, and "tablet" settings. Total three options for settings on the desktop of the Square Home launcher. In the screenshot, three types brought to their desk in the lower left corner.
Who needs a detailed instruction for installing and configuring the entire launcher and how to output these settings, write in a personal.


Post has been editedkoss7777 - 30.07.19, 09:22

If complicated, do not do in any way. In Root Explorer editing mode, it is easy to ruin everything.

Posted 07/30/2019, 9:22:


It is necessary root explorer. I changed the description, now it is not necessary to add the application to the tiles group.


I did not work with me neither Power Shortcuts nor Shortcut Master. Strange, but either the icon was not created on the desktop, or nothing happened when pressed.
Why I started editing ...

Post has been editedLoGatto - 30.07.19, 09:28

Vasily_5 ,
1. Run the Square Home launcher.
2. Click on the original console button "Three strips" menu will appear.
3. Select "Backup" menu. We give permission to create a folder in boxing memory. The Squarehome2_Backups folder is created.
4. Download the file. Any root explorer copy two folders.
Vasily_20190708.
Vasily_20190730.
You can copy 2 to your discretion to the created SQUAREHOME2_BACKUPS folder.
5. In the launcher, we press the "Three Dash" button on any remote, even in the Fly Console voice.
6. Choose a backup as your discretion is more suitable.

P. S After creating your DESKTOP variation, we save your backup. Transfer to any boxing.
But there is a "but" versions of the launcher must coincide.

Everything is simple and convenient. Already created Droid Settings, TV Settings, White settings, Top Panel Disclosure, Curtains,
View Memory Ram, Internal ROM memory, installed in the Flash memory box, goes immediately reading free memory to flash connected boxing.
Screenshots
Download Backup.Squarehome2_backups.7z.(1.84 MB)

If you need wallpapers Windows 10 as I can throw off.

Post has been editedVasily_5 - 30.07.19, 09:52

You can do this, just get two clicks:
Add ->Application ->Memory Wiper.

Post has been editedLoGatto - 30.07.19, 09:53

I also had this, you did not give any permission to Squarehome, look at the Android settings and give all permissions.

See settings>special opportunities>Downloaded services>SquareHome Switch is turned on?
In general, while, in my opinion, with the help of Power Shortcut the easiest way. Option from Vasily, well, too, such a solution. Suitable if you are from scratch put Squarehome and you have a naked desktop. If you are all configured, then restoring someone else's backup will be updated. Yes, and a bunch of labels with the settings on the table too bust. One label from which you can get to any settings is still more convenient.UpdatedManual to add a label in his post, now in general as two fingers ..

Posted on 07/30/2019, 10:49:

Why in a personal? Many are interested in this question, if not difficult to write the manual and lay out. Well, or send me in hp

Post has been editedvita911 - 30.07.19, 12:26

Colors are very saturated where you can not disconnect or turn on something I do not understand

Or it seems to me after another boxing, faces are not red natural

The prefix is ​​sharpened under the HDR mode, it works initially with him by default. I heard those who have no HDR on TV, there are problems with excessive saturation.

Indeed, the Square Home is turned off, and Power Setup.
I'll try to turn on ...

And how could you guess about this?

Posted on 07/30/2019, 12:00:


So you can remove any tile from the table. And the application, if you need, run from the overall tile applications.

Tell me, is there an IPTV, where can I switch channels with the PG + / PG-standard remote control with voice search? Or maybe they are somehow programmed?

Ezquerro , Not the prefix system is initially sharpened under HDR auto mode.
But if this mode bothers you.
You can go to tv setting =>Advanced settings. =.>Display. There is changing HDR to SDR =>SDR to HDR.
To see what mode for you more clearly can be seen in Smart TV YouTube.
In the same all famous Costa Rica rollers.
When you run the video will be a video quality selection and change the mode with HDR and without HDR.
On my TV mode with HDR more visual.
Therefore, in the settings I leave the HDR mode. Those clips or rollers that go in HDR mode are reproduced in HDR.


Post has been editedVasily_5 - 30.07.19, 12:24

Jaksi
A similar problem on tvoetv.in.ua their application TV.apk, constantly hangs the box, only dismaying power displays, wrote the developer, they said that they would look at the problem, but I doubt that they would be bathed.
Eden through the outplareer works without problems, as well as 1080p hinges without problems

Disassembled, so different versions of the boards went

The antenna was brought, but WiFi module is already different

madobikt777 , In my opinion ampak model better.
MediaTek I do not remember in my opinion does not have a two-way Wi-Fi.
Yes, now the systems will not approach one another.
We must be attentive to open the box to watch.

Post has been editedVasily_5 - 30.07.19, 13:49