TP-LINK WDR3600 - Discussion [OpenWRT, DD-WRT, TP-Link, Gargoyle, etc.] | [WiFirouter, USBWIFI, Firmware] 300 MB / s (2.4 and 5 GHz), 5x1 GB / s, 2xUSB



Rep: (21)
TP-LINK WDR3600 - Discussion [OpenWRT, DD-WRT, TP-Link, Gargoyle and others ..] - Discussion
WiFirouter, USBWIFI, Firmware: 2.4GHz (300Mbit \ s) - 5GHz (300Mbit \ s) + 5 • 1Gbit \ s | USB: X2 (3G or 4G Modem), SAMBA server support (data storage), FTP server, media server, print server.

Attached Image

The forum decided to post images under the spoiler

A photo
Attached Image
Attached Image
Attached Image
Attached Image
Description
The total bandwidth capacity is up to 600 Mbps: up to 300 Mbps by 2.4 GHz and up to 300 Mbps per 5 GHz.
2 USB ports to create shared access to printers, files and multimedia on a local network or remotely via the FTP server.
Gigabit ports allow you to achieve maximum data rates.
Thanks to the hardware NAT, the maximum WAN bandwidth to LAN reaches 800 Mbps.
IPTV: IGMP Proxy support and Bridge mode for IPTV multicast stream, 802.1Q TAG VLAN.
Guest network provides separate access to a wireless network for guest users.
Specifications
Interface 4 LAN ports 10/100/1000 Mbit / s
1 10/100/1000 Mbps WAN port
2 USB 2.0 ports
Buttons WPS / Reset Button
Wireless ON / OFF Switch
Power On / Off Button
External power supply 12 in post. current / 1.5 A
Dimensions (WxLxH) 243 x 160.6 x 32.5 mm
Antenna 2 external removable dual-band antennas (RP-SMA connector)
PARAMETERS OF WIRELESS MODULE
IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n Wireless Network Standards
Frequency range (reception and transmission) 2400-2483.5 MHz 5150-5350 MHz 5650-5725 MHz
Skoroct 5 GHz transmission up to 300 Mbit / s
2.4 GHz: up to 300 Mbps
Sensitivity (reception) 270 Mbps 2.4 GHz: -70 dBm
195 Mbps 2.4 GHz: -71 dBm
130 Mbps 2.4 GHz: -74 dBm
54 Mbps 2.4 GHz: -79 dBm
6 Mbps 2.4 GHz: -94 dBm
270 Mbps 5 GHz: -67 dBm
195 Mbps 5 GHz: -70 dBm
130 Mbps 5 GHz: -73 dBm
54 Mbps 5 GHz: -79 dBm
6 Mbps 5 GHz: -92 dBm
EIRP (Wireless Power)<20 dBm or<100 mW
Wireless Mode Functions Enable / Disable Wireless Broadcasting, WDS, WMM Bridge, Wireless Statistics
Wireless Security 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK encryption
Guest network 1 Guest network at a frequency of 2.4 GHz 1 Guest network at a frequency of 5 GHz
Model TL-WDR3600
Version 1.1, 1.2, 1.3, 1.4, 1.5
Soc Atheros AR9344.
CPU MHz 560.
Flash: 8 MB
RAM: 128 MB
WLAN HARDWARE: AR9344, ATHEROS AR9582
WLAN2.4: B / G / N
WLAN5.0: A / N
Gbit Ports: 5
USB: 2x 2.0
Firmware
Useful


Post has been editedzdimaby - 02.05.20, 18:19



Rep: (5)
Tell me where to take OpenWRT, the latest version with Russian language and 4G modems support?



Rep: (21)
KS753 @ 11.04.20, 21:43*
Tell me where to take OpenWRT, the latest version with Russian language and 4G modems support?

Here: TL-WDR3600-V1 19.07.2.zip
factoryTo move from other firmware
sysupgradeTo transition different versions of OpenWRT
Firmware is taken here:CRY. We choose the version of the Valley Click on "targets /" and select our processor "AR71XX /" Dality Clay "Generic /" and in the browser we click "Ctrl + F" and in the window we drive 3600 Tuisty our model of the router and the lzhukh ... is our firmware TL-WDR3600-V1-Squashfs-sysuppograde.bin and TL-WDR3600-V1-Squashfs-Factory.bin.
2: It depends on your modem if for example e3372, e8372 (firmwarehighlinknot stycated) and the like that is simply in the "Software" tab (do not forget to click "Update Lists") We are looking for and installusb modeswitchandkmod-usb-net-cdc-etherAnd the modem is immediately determined in the system as a network interface, in my case as an ETH1 device. Go to "Network" - "Interfaces" and click on Add New Interface ... You need to add our modem and solve the network from it. The interface name indicates USB, DHCP protocol, and the Ethernet Adapter interface: ETH1. Click on submit. In the connection that appears, select Edit, go to the Firewall Settings tab and indicate the WAN zone for it: That's all.
3: Russian is also installed through "Software" packages seemluci-i18n-base-ruandluci-i18n-firewall-ruRusification Base, Firewall .. speaks from English for itself.

Attached files

Attached fileTL-WDR3600-V1 19.07.2.zip(7.85 MB)
Attached fileTL-WDR3600-V1 19.07.4.zip(7.86 MB)


Post has been editedzdimaby - 21.10.20, 16:13



Rep: (5)
Salexa @ 02.22.20, 02:31*
Compiled and checked as part of OpenWRT 19.07.1


Installed OpenWRT 19.07.2 R10947-65030D81F3. Next, installed through the Software Your version of Memtester (it appeared in the Installed section). But I do not understand how to run it?



Rep: (21)
KS753 @ 12.04.20, 11:28*
But I do not understand how to run it?

Try through SSH Putty to commandMemtester 90m 10.



Rep: (5)
In OpenWRT 19.07.2 R10947-65030D81F3 in the Software-Updates section there is a list, I understand every item you can upgrade to a more recent version. Is it worth updating everything? or better not to risk, it works and works

Attached images
Attached Image


Post has been editedKS753 - 12.04.20, 13:06



Rep: (145)
KS753 @ 12.04.20, 12:43*
Is it worth updating everything?

no need, works and let yourself work



Rep: (21)
KS753 @ 12.04.20, 12:43*
Is it worth updating everything?

No, a lot of memory takes ..



Rep: (0)
Hello everyone. To install and configure a VPN server on the router, such as PPTP or L2TP? OpenWRT firmware 19.07.2.



Rep: (108)
* Legsis Start with the OpenWRT documentation:
openwrt.org/docs/guide-user/services/vpn/pptp/basic.



Rep: (5)
* zdimaby,
Everything happened other than paragraph 2. I installed these 2 packages, I connected the E3372H modem (M150-2). The indicator on the router burns yellow, the blue indicator flashes on the modem itself (type 4G caught). But in the Interface section does not appear new devices and when I try to add a new interface there is no modem. Or I do not look there. Tell me.

Attached images
Attached Image
Attached Image


Post has been editedKS753 - 19.04.20, 13:00



Rep: (21)
KS753 @ 19.04.20, 12:59*
But in the Interface section does not appear new devices.

Go to "Status" Dality "System Journal" and see whether USB should be something like that
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: Network Device 'Eth1' Link Is Down
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: Interface 'E3372' Has Link Connectivity Loss
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: E3372 (9212): UDHCPC: SIOCGIFINDEX: No Such Device
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: E3372 (9212): UDHCPC: Reced Sigterm
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: Interface 'E3372' IS Now Down
Sat Apr 18 18:36:47 2020 Daemon.Notice Netifd: Interface 'E3372' is Disabled
Sat Apr 18 18:36:47 2020 Daemon.warn DNSMASQ [3231]: No Servers Found in /tmp/resolv.conf.auto, Will Retry
Sat Apr 18 18:36:54 2020 kern.info kernel: [535254.781916] USB 1-1.1: New High-Speed ​​USB Device Number 97 using Ehci-Platform
Sat Apr 18 18:36:54 2020 kern.info kernel: [535255.510757] USB 1-1.1: USB DISCONNECT, Device Number 97
Sat Apr 18 18:36:55 2020 kern.info kernel: [535255.872030] USB 1-1.1: New High-Speed ​​USB Device Number 98 using Ehci-Platform
Sat Apr 18 18:36:55 2020 kern.info kernel: [535256.057982] CDC_ETHER 1-1.1: 1.0 ETH1: REGISTER 'CDC_ETHER' AT USB-EHCI-Platform-1.1, CDC Ethernet Device, 0c: 5b: 8f: 27: 9A: 64.
Sat Apr 18 18:36:55 2020 kern.err kernel: [535256.072487] CDC_ETHER 1-1.1: 1.0 ETH1: KEVENT 12 MAY HAVE BEEN DROPPED
Sat Apr 18 18:36:55 2020 kern.err kernel: [535256.085782] CDC_ETHER 1-1.1: 1.0 ETH1: KEVENT 11 MAY HAVE BEEN DROPPED
Sat Apr 18 18:36:55 2020 kern.err kernel: [535256.101776] CDC_ETHER 1-1.1: 1.0 ETH1: KEVENT 11 MAY HAVE BEEN DROPPED
Sat Apr 18 18:36:55 2020 Daemon.Notice Netifd: Interface 'E3372' is Enabled
Sat Apr 18 18:37:01 2020 Daemon.Notice Netifd: Network Device 'Eth1' Link Is Up
Sat Apr 18 18:37:01 2020 Daemon.Notice Netifd: Interface 'E3372' Has Link Connectivity
Sat Apr 18 18:37:01 2020 Daemon.Notice Netifd: Interface 'E3372' Is Setting Up Now
Sat Apr 18 18:37:01 2020 Daemon.Notice NetiFD: E3372 (9827): UDHCPC: started, v1.30.1
Sat Apr 18 18:37:01 2020 Daemon.Notice NetiFD: E3372 (9827): UDHCPC: Sending Discover
Sat Apr 18 18:37:01 2020 Daemon.Notice Netifd: E3372 (9827): UDHCPC: Sending Select for 192.168.8.100
Sat Apr 18 18:37:01 2020 Daemon.Notice Netifd: E3372 (9827): UDHCPC: Lease of 192.168.8.100 Obtained, Lease Time 86400



Rep: (145)
KS753 @ 19.04.20, 12:59*
Everything happened besides paragraph 2. I installed these 2 packages,

I worked with this with this (I found a reminder):
USB-MODESWITCH (Utilites)
KMOD-USB NET-CDC-Ether (Kernel Modules>USB Support>KMOD-USB-NET)
KMOD-USB NET-RNDIS (Kernel Modules>USB Support>KMOD-USB-NET)
sources:time two

Post has been editedsegerist - 19.04.20, 13:48



Rep: (5)
* segerist,
Does not appear, the modem in Keenetic 4G II quietly works, and here in any way



Rep: (28)
Ks753 @ 19.04.20, 15:12*
Does not appear, the modem in Keenetic 4G II quietly works, and here in any way

Maybe the fact is that the Stick modem, not Hilink? And for its functioning need the appropriate packages?



Rep: (145)
Ks753 @ 19.04.20, 15:12*
Does not appear, the modem in Keenetic 4G II quietly works, and here in any way

Well, actually yes:
NX-COLD @ 19.04.20, 15:15*
Maybe the fact is that the Stick modem, not Hilink? And for its functioning need the appropriate packages?



Rep: (5)
* Nx-cold,
* segerist,
You were right, craftsmen from the next branch helped me flash modem in Hilink. Earned ... Hurray. But damn one cured the second broke. Now when I'm trying to go to the routerhttp://192.168.1.1writes where to dig?

/usr/lib/lua/luci/dispatcher.lua:315: / etc / config / luci seems to be corrupt, unable to find section 'main'
stack traceback:
[C]: in function 'assert'
/usr/lib/lua/luci/dispatcher.lua:315: in function 'dispatch'
/usr/lib/lua/luci/dispatcher.lua:208: in function</usr/lib/lua/luci/dispatcher.lua:207>



Rep: (21)
KS753 @ 19.04.20, 20:18*
Now when I'm trying to go to the routerhttp://192.168.1.1writes where to dig?

You probably found something or something .. OpenVPN probably I didn't do something wrong, I think it will restore it easily through TFTP either through SSH to reset the settings ..



Rep: (5)
* zdimaby,
I just installed it

USB-MODESWITCH (Utilites)
KMOD-USB NET-CDC-Ether (Kernel Modules>USB Support>KMOD-USB-NET)
KMOD-USB NET-RNDIS (Kernel Modules>USB Support>KMOD-USB-NET)



Rep: (5)
* zdimaby,
I have OpenWRT. I downloaded from the header TFTPD64 + firmware. Turn off the antivirus and Bryrahmaer. The address on the map 192.168.0.66. Opened from the TFTPD64 administrator. Selected 192.168.0.66. I pressed the reset on the router until the SSB indicators had not flashes. But the firmware does not begin. Laptop Window 7 64. Connected by twisted pair to the router
Addition. After pressing the reset in the TFTPD64 program in the Server Interfaces section it changes for: 1

Post has been editedKS753 - 20.04.20, 09:18



Rep: (28)
* Ks753,
If there is access to SSH, then perform
firstboot


Full version    

Help     rules

Now: 03.01.21, 03:51