Tp-Link Archer C60 - discussion пїЅ
wifirouter wifirouter: 2.4GHz (450Mbit \ s) - 5GHz (867Mbit \ s) | 4 • 100Mbit \ s | USB: no




Post has been editedAndrewP_1 - 31.01.19, 17:09

Good day everyone! Tp-Link Archer C60 device. WIFI does not work at a frequency of 5 GHz !!! During the quick setup, WIFI 5GHz is not active, on the screenshot below it is clear that due to the region, it is also not possible to change the region except Moscow. Can anyone come across? The first time I see this)
http://joxi.ru/82QWQVPHjkQXLr

all good, mos

Hello. Acquired Router Tp-Link Archer C60 6 December this year. After 3 days in the router appeared clicks. Clicks can be heard even togda.kogda all devices are turned off. Basically audible clicks when I turn on the computer to the Internet. Clicks these fickle. And when there were clicks, then the Internet via cable and Wi-Fi sometimes malfunctions. Already in tehpoddezhku TP-LINK company appealed. So there I was asked to connect the router to a different computer, or even TV, and even advised to replace the cable. Yes, that's the sense of it. Though before I had another router TP-LINK WR-841N and the router also appeared clicks - even some other cable is connected to the LAN - Router socket and the socket of the PC network card, but clicks are still not stopped. The Archer C60 firmware has not changed, so the firmware on the drive up and running. The router is on the table near the monitor, and very close to the computer speakers. I can not put on the router due to a short cable. The router in the connected ordered. I read online reviews about this router, and many recommend to upgrade the firmware to a newer. Except that no one wrote about audible clicks in the router
I will try then to update on the firmware that is on the site itself. Third-party firmware is still scary to install and the router is still under warranty.

On the Tp-Link site itself, the same firmware as the factory one is installed. I'll try to install the English firmware better. Rather, the Russian firmware has not been completely fully developed.

Greetings. I would like to know how you c60?

Artur_nt.84 , normally, two computers are connected by wires and two phones via wi-fi, everything works. The only thing my wife has tel. Meizu at a frequency of 5 GHz with interruptions took, at 2.4 norms. I have Honor, everything is ok. Yes, I had to tinker with the settings. There is a "quick setup" in the menu, with its help I could not connect to the provider. I went to the "setting" item, everything turned out there.

asl70.a ,
Thank. I bought it, but have not yet unpacked it.) I live in a private house, I decided to carry out optical fiber. C60 more than 100mbi for wifi gives out?

Artur_nt.84 , I have a provider up to 100mb, so it will no longer issue. 80-90 gives out.

asl70.a ,
Clear. Holiday greetings)

Artur_nt.84 and you too.

Zravstvuyte. New firmware for this router has absolutely not. I am looking for the firmware on the English site, but did not find. I reset the router to factory settings in the web-interface, but somehow the Internet through a router with dropped on factory settings and worked. Usually, after dropping to factory settings via a router Internet stops working, and I work here. Then again I dropped the router to factory default setting, but pressing the button on the router and the Internet, too, worked. But after a reset to factory settings I have hovered web- interface and I could not configure the router. That is not even to be floating, and zaglyuchil. The web-interface point out that I have a dynamic IP-shake and save. After this IP-address and DNS are discharged and it is necessary to re-tune again, but still resets. Even load on the CPU is at 100%. Only after restarting the router in the web-interface I was able to configure the router. I did not understand what it was. And flashing worth factory in 2016, which is on the Russian site TP-LINK. Already in 2018, and firmware with corrections so still and there. The router itself for the night off. The router has not yet been finalized.

Hello
some kind of crap is going on
when trying to configure and connect to the router network cable indicator lights up red
in the end, there is no internet through the Wi-Fi or through the cord
There are no problems when connecting the cord to the computer immediately

viktorvip The menu has a "quick setup", with its help I could not connect to the provider. I went to the "setting" item, everything turned out there.
P.S. I quote myself.


Post has been editedasl70.a - 17.01.18, 19:38

Apparently you do not stick there. The cable provider in the Wan blue port is separate. PC cable in any of 4 yellow. further through the web we make the setting 192.168.0.1
After configuration, it is advisable to change the Lan network address to 192.168.1.1. I do not know why, then so advises TP TP-link

Looking bad. There are 2 beta firmware fixes problems with PPTP / L2TPArcherC60v1_ru-up-ver1-0-0-P1 [20180111-rel59955] _beta.zip(7.78 MB)
ArcherC60v1_ru20171114 (1) .rar(7.7 MB)

before and after flashing reset to factory settings. change the network address of the router to 192.168.1.1
thread in the profile forumhttps: //forum.tp-linkr...topic.php? f = 402 & t = 9925
On the firmware [20180111-rel59955] _beta.zip, the session lasts for some reason 9h 9min
There are known problems with PPTP / L2TP with providers of Flex and Spidilayn of the Moscow region

Post has been editedpredator212 - 23.01.18, 17:05

about performance.
100Mbps channel
By 95Mbps cable
on radio 85 jump / 95 recoil

Launched PPTP server. , I connect from the laptop from the Internet, the connection happens, but I don’t see my lokalki. Shouldn't the router itself rebuild routes? When adding a route to the manual on the laptop, I ping only the lan of the router itself. And then silence.

Tell me pzh somebody tried to install the firmwareLEDE . And then I have C60 v1 (EU) on which iptv falls off from the provider on wifi 2.4 GHz. And I do not see any corrections for him, and if so, other corrections and not for him.
P.S. RU not put on EU

Good evening

Archer C60 (EN) V2 - who knows how to put LEDE / OpenWRT on it. I found the firmware only for C60 (EU) V2 - it does not get up either through the WEB face, or through TFTP recovery mode.

I also tried to fill it with a regular one for C60 (EU) V2 - it also does not charge, the wrong firmware writes. Can something change in a hex editor?

And no one will tell - on the standard firmware udpxy can not be raised?