Archer C7 - Discussion | Wi-Fi Router



Rep: (1)
TP-Link Archer C7 (AC1750 Dual Band Wi-Fi Gigabit Router)- Discussion
Wi-Fi Router 802.11a / b / g / n / ac | 2.4GHz frequency (450Mbit \ s) | 5GHz frequency (1300Mbit \ s) | LAN 4x1000Mbit \ s | USB 2x2.0 type A |

Attached Image

The forum decided to post images under the spoilerPicture

Specifications
HARDWARE CHARACTERISTICS
Interface 4 LAN ports 10/100/1000 Mbit / s
1 10/100/1000 Mbps WAN port
2 USB 2.0 ports
Buttons WPS / Reset Button
Wireless on / off button (wireless on / off)
Power On / Off Button
External power supply 12 V DC / 2.5 A
Dimensions (WxLxH) 243 x 160.6 x 32.5 mm
Antenna type 3 removable 5 GHz antennas with 5 dBi gain (RP-SMA)
3 internal 2.4 GHz antennas

PARAMETERS OF WIRELESS MODULE
IEEE 802.11ac / n / a wireless standards for 5 GHz frequency
IEEE 802.11b / g / n for the 2.4 GHz frequency
Frequency range (receive and transmit) 2400-2483.5 MHz
5150-5350 MHz
5 GHz transmission speed: up to 1300 Mbps
2.4 GHz: up to 450 Mbps
Sensitivity (reception) 5 GHz пјљ
11a 6 Mbps -96 dBm
11a 54 Mbps: -79 dBm
11ac HT20: -71 dBm
11ac HT40: -66 dBm
11ac HT80: -63 dBm
2.4 GHz
11g 54M: -77 dBm
11n HT20: -74 dBm
11n HT40: -72 dBm
EIRP (Wireless Power)<20 dBm or<100 mW
Wireless functions Enable / disable wireless broadcast, WDS bridge, WMM, wireless connection statistics
Wireless Security Encryption Modes: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK

CHARACTERISTICS OF SOFTWARE
QoS (data prioritization) WMM, bandwidth control
WAN connection type Dynamic IP / Static IP / PPPoE /
PPTP (Dual Access) / L2TP (Dual Access) / BigPond
Management Access Control
Local management
Remote control
DHCP server, client, list of DHCP clients,
address reservation
Port Forwarding Virtual Server, Port Triggering, UPnP, DMZ
Dynamic DNS DynDns, Comexe, NO-IP
VPN traffic pass PPTP, L2TP, IPSec
Access Control Parental Control, Local Management Control, Node List, Scheduled Access, Rules Management
Network security (firewall) Protection against DoS attacks, SPI firewall, filtering by IP address / MAC address, domain name, binding by IP and MAC address
Protocols Supports IPv4 and IPv6
Shared via USB Support Samba (storage device) / FTP server / media server / print server
2.4 GHz guest network guest network
one 5 GHz guest network

OTHER
CE, FCC, RoHS certification
Package Archer C7
3 removable antennas
Power adapter
Ethernet cable
Quick Setup Guide
System Requirements Microsoft Windows 98SE, NT, 2000, XP, Vista в„ў or Windows 7, Windows 8 / 8.1 / 10
MAC OS, NetWare, UNIX or Linux
Environmental Parameters Operating Temperature: 0 в„ѓ - 40
Storage temperature: -40 в„ѓ - 70 в„ѓ
Operating Humidity: 10% - 90%, without condensation
Humidity during storage: 5% - 90%, without condensation
Firmware
Dumps
Attached fileРЎ7V2.zip(8.95 MB)
Useful


Post has been editedstp101 - 15.10.20, 13:47
Reason for editing: Dump Archer c7 v5



Rep: (-2)
A.r.c.h.e.r. @ 06/03/18, 04:10*
you watch in wifi analizer a more free channel, you put it


Thank you.
I live in a private house, there are no other people's networks. The router is in the attic and does not reach the arbor. I read that there is a limit on the signal power in the region. Put OAE, added power, but nothing has changed = (



Rep: (58)
Elvis666 @ 06/03/18, 09:51*
I live in a private house, there are no other people's networks. The router is in the attic and does not reach the arbor.

it’s good that there are no neighbor networks. For more than 20-21 you will not get power, try to lower it from the attic to the room or connect a second router in client-bridge mode to it, you will get one network, the second router will amplify the signal from the first.

Post has been editedfaceless - 03.06.18, 10:33



Rep: (126)
Elvis666 @ 06/03/18, 11:51*
The router is in the attic and does not reach the arbor

The story turned into a joke of the 90s ...

A friend bought a cordless telephone (not even dect yet) and asked a friend - how to check that the phone is good? Friend:
- Well, you call whoever you are and leave the base at 10m. If the sound is normal, then the phone is normal. Then you go back to 20m. If you hear, then the phone is not bad. We leave for 30m. If you hear, then the phone is good. Depart to 40m, if you can still hear, the phone is excellent. Depart to 50m. if it works, then you have a nice apartment ...

Why is this? ... You have a good site!

I have Khrushchev, 5th floor, an apartment behind the wall from the entrance (the windows are not in the courtyard), a router under the ceiling. Sitting in a car in my pocket in front of the entrance I catch a signal, I can read the mail while I wait for my wife (the signal is barely visible, but visible!)

Gargoyle firmware (well, this is the same openwrt. Settings 2.4 (5 naturally does not catch behind an apartment): channel width - 20, power - maximum.



Rep: (6)
Good day to all. Yesterday decided to put the firmware of the cap DD-WRT for the hardware version Ver.1, through an interface restart and stop defining normal laptop via Ethernet, just as unknown utroystvo, via Wi-Fi in general is not defined. The interface does not go not in one of the proposed cap. Trying to connect, and then takes himself restarts, and cyclically. Manipulation of the restoration through a program like did not help. I do not know what to do, ask your assistance, only one router.



Rep: (8)
The people, and in v.4 is it possible to limit the guest network in speed?
I want to leave it open, let the guests use it, it’s enough for 500 Mbps for the eyes, but there are arrogant neighbors who can download something completely, so I would like to limit the speed, but I didn’t see anything like that in the settings.



Rep: (58)
* stinger1994,
tried to reset the settings via the reset button? How was it flashed?

Manipulations with recovery through the program did not seem to help - which program?

Post has been editedfaceless - 04.06.18, 20:27



Rep: (126)
Boty2007 @ 06/04/18, 20:35*
I want to leave open

Laurels of Dmitry Bogatov do not allow to live in peace?



Rep: (58)
Boty2007 @ 06/04/18, 18:35*
but there are arrogant neighbors who can even download something in full, so I would like to limit the speed, but I didn’t see anything like that in the settings.

put the poppies filter

Post has been editedfaceless - 04.06.18, 20:40



Rep: (8)
A.r.c.h.e.r. @ 06/04/2018, 20:35*
...
poppy filter


As I understand it, it will be necessary to enter all the addresses, and the goal is just the same so that guests do not enter passwords, there were no problems.

For some reason I thought that, whatever one may say, there is in the router,) I am surprised that it is impossible. People come in, including at work, and there are cases of using wifi for purposes that do not meet the requirements of the law, then explain where the person you saw once in your life has a password from the home network. It’s easier here, who needs it, uses it, without unnecessary information.



Rep: (286)
* boty2007,
Bring the neighbors and block them. In general, just enter the password once for your guests and that’s all. Or do you have a passage yard? :)



Rep: (440)
Boty2007 @ 06/04/18, 18:35*
and in v.4 is it possible to limit the guest network in speed?

In Padavan there is such a chip
Attached Image



Rep: (6)
* A.r.c.h.e.r.,
Stitched, as indicated in the instructions.

factory-to-ddwrt.bin - file for installing DD-WRT from under the router’s native firmware.

webflash.bin - file for updating from the already installed DD-WRT.

For some models, only one file is available for all operations.

For initial installation of DD-WRT:

In the address bar of the browser we typehttp://192.168.1.1orhttp://192.168.0.1, depends on the router, enter the authorization data and update the factory-to-ddwrt.bin file through the standard update menu in your router.
After some time, the router will reboot, after which you will see the updated interface (DD-WRT's address is 192.168.1.1 by default). On the main page when you first start you need to specify the username and password for administration.
Firmware dd-wrt installed, you can proceed to configure. (It is also recommended to do a reset to the factory settings after the firmware and before the setting)

Esli you are having problems it is impossible to go to the admin panel DD-WRT firmware after, go to the network connections on your computer and make sure that the ip addresses are given correctly: ip: 192.168.1.xxx (last digit may vary) Mask: 255.255.255.0 gateway: 192.168.1.1. If the addresses are different, then the easiest option to restart the network card (.. On and off again when the network asks for dhcp addresses), if this does not work, enter manually, for example ip 192.168.1.2, mask: 255.255.255.0 Gateway: 192.168. 1.1 and try again to enter the browser to the address 192.168.1.1.

To update an already installed DD-WRT:

In the DD-WRT menu, select “Administration” - in the submenu, select the item “Firmware upgrade”. Click on the “select file” button and specify the webflash.bin firmware that you downloaded earlier. Click on the “Upgrade” button, the software update process will begin.

Link tosavagemessiahzine.com. DD-WRT - alternative firmware

Tried to recover according to this instruction.

https://proadminz.ru/v...ki-tp-link-tl-wr842nd/



Rep: (-2)
Someone managed to restore the Archer C7 v4 router.
Tried through Tftpd32, renamed the firmware to ArcherC7v4_tp_recovery.bin
The IP router has 192.168.1.1 (I tried to set 192.168.1.66 and 192.168.0.1) [
But nothing helps, does not cling.

Post has been editedelvis666 - 05.06.18, 21:05



Rep: (58)
* elvis666 , restore which firmware from which? Write more.

Posted on 06/05/2018, 22:14:

* stinger1994 Do you want to restore stock from DD-VRT?

Post has been editedfaceless - 05.06.18, 22:12



Rep: (6)
* A.r.c.h.e.r., in my recovery through the same program how to be? How do I restore the router now?



Rep: (58)
* stinger1994 ,
Return to stock firmware from DD-WRT for V.4:
1.Download firmware from your website TP-Link to your router or a ready-made file:Attached fileArcher C7 (RU) _V4_171130.zip(14.9 MB)
2.Download to your LEDE router from here:https: //downloads.lede...argets/ar71xx/generic/,(download only factors) or a ready-made file:Attached fileArcherC7v4_tp_recovery.zip(3.56 MB)
(skip point 4), extract the firmware from the archive.
3.On the PC network card, set: mask 255.255.255.0, ip 192.168.0.66
4. Renamed LEDE firmware in ArcherC7v4_tp_recovery.bin
5. Through tftp I flashed LEDE (turn off the antivirus / firewall, in the off state of the router we hold down the reset button and without releasing it turn on the router, as the indicator starts to move in the programtftpdrelease the reset button and wait for the end, the router will automatically reboot (sew only with a factor file).
6. Rename the stock firmware to ArcherC7v4_tp_recovery.bin or a ready-made file:Attached fileArcherC7v4_tp_recovery.zip(14.49 MB)
, extract from the archive and sew it through tftp.
7. After reboot, the router will download the stock firmware.

Post has been editedfaceless - 22.09.18, 14:15



Rep: (-2)
A.r.c.h.e.r. @ 06/05/18, 19:26*
Through tftp I flashed LEDE.


I can’t flash it.

1) connected the router by cable to the LAN 1 socket
2) Set on the network card 192.168.0.66, mask 255.255.255.0
3) renamed the firmware to ArcherC7v4_tp_recovery.bin
4) downloaded, installed, launched tftpd32 standard edition (installer) v4.52, chose a place with firmware, remained on the SERVER tab
5) turned off the router with the off button, clamped a reset clip, turned on the router
6) waited 15 or more seconds, nothing happened.



Rep: (440)
Elvis666 @ 06/06/18, 14:51*
I can’t flash it.

Tp-Link Archer C60 - Discussion (Post by Herzz # 73797458)



Rep: (-2)
Herzz @ 06/06/18, 11:57*
Tp-Link Archer C60 - Discussion (Post by Herzz # 73797458)


Archera C7 does not have such a recovery.



Rep: (-2)
Earned TFTPD

1 - Disabled Firewall on Windows
2 - Installed Tftpd64 latest version
3 - Change the cable (stood yellow from Zyxel) to another, with 8 cores.
4 - For drying, ethernet installed Wireshark, looked what really requests the address 192.168.0.66 and the name of the firmware ArcherC7v4_tp_recovery.bin
5 - I pressed the reset, turned it on, waited 6 seconds, the firmware downloaded, the router blinked for 2 minutes, it restarted
6 - The stock returned.


P.S. it was in the cable O_O


Full version    

Help     rules

Time is now: 22/10/20, 9:40