Archer C7 - Discussion | Wi-Fi Router

Rep: (1)
TP-Link Archer C7 (AC1750 Dual Band Wi-Fi Gigabit Router)- Discussion
Wi-Fi Router 802.11a / b / g / n / ac | 2.4GHz frequency (450Mbit \ s) | 5GHz frequency (1300Mbit \ s) | LAN 4x1000Mbit \ s | USB 2x2.0 type A |

Attached Image

The forum decided to post images under the spoilerPicture

Interface 4 LAN ports 10/100/1000 Mbit / s
1 10/100/1000 Mbps WAN port
2 USB 2.0 ports
Buttons WPS / Reset Button
Wireless on / off button (wireless on / off)
Power On / Off Button
External power supply 12 V DC / 2.5 A
Dimensions (WxLxH) 243 x 160.6 x 32.5 mm
Antenna type 3 removable 5 GHz antennas with 5 dBi gain (RP-SMA)
3 internal 2.4 GHz antennas

IEEE 802.11ac / n / a wireless standards for 5 GHz frequency
IEEE 802.11b / g / n for the 2.4 GHz frequency
Frequency range (receive and transmit) 2400-2483.5 MHz
5150-5350 MHz
5 GHz transmission speed: up to 1300 Mbps
2.4 GHz: up to 450 Mbps
Sensitivity (reception) 5 GHz пјљ
11a 6 Mbps -96 dBm
11a 54 Mbps: -79 dBm
11ac HT20: -71 dBm
11ac HT40: -66 dBm
11ac HT80: -63 dBm
2.4 GHz
11g 54M: -77 dBm
11n HT20: -74 dBm
11n HT40: -72 dBm
EIRP (Wireless Power)<20 dBm or<100 mW
Wireless functions Enable / disable wireless broadcast, WDS bridge, WMM, wireless connection statistics
Wireless Security Encryption Modes: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK

QoS (data prioritization) WMM, bandwidth control
WAN connection type Dynamic IP / Static IP / PPPoE /
PPTP (Dual Access) / L2TP (Dual Access) / BigPond
Management Access Control
Local management
Remote control
DHCP server, client, list of DHCP clients,
address reservation
Port Forwarding Virtual Server, Port Triggering, UPnP, DMZ
Dynamic DNS DynDns, Comexe, NO-IP
VPN traffic pass PPTP, L2TP, IPSec
Access Control Parental Control, Local Management Control, Node List, Scheduled Access, Rules Management
Network security (firewall) Protection against DoS attacks, SPI firewall, filtering by IP address / MAC address, domain name, binding by IP and MAC address
Protocols Supports IPv4 and IPv6
Shared via USB Support Samba (storage device) / FTP server / media server / print server
2.4 GHz guest network guest network
one 5 GHz guest network

CE, FCC, RoHS certification
Package Archer C7
3 removable antennas
Power adapter
Ethernet cable
Quick Setup Guide
System Requirements Microsoft Windows 98SE, NT, 2000, XP, Vista в„ў or Windows 7, Windows 8 / 8.1 / 10
MAC OS, NetWare, UNIX or Linux
Environmental Parameters Operating Temperature: 0 в„ѓ - 40
Storage temperature: -40 в„ѓ - 70 в„ѓ
Operating Humidity: 10% - 90%, without condensation
Humidity during storage: 5% - 90%, without condensation
Attached fileРЎ MB)

Post has been editedstp101 - 15.10.20, 13:47
Reason for editing: Dump Archer c7 v5

Rep: (286)
* Anastezija
If a
With a network of displeasure

What do you want to see?

Post has been editedNun70 - 17.02.18, 09:25

Rep: (55)
I am also not a great expert. There is also a disk, the goal is the same, so that I can see it from two smart TVs to Wi-Fi, two laptops, two phones. Is it realizable?
Some videos from the disc would like to watch in tlf. No download via ftp

Post has been editedfsm888 - 17.02.18, 16:10
Reason for editing: T9

Rep: (286)
* fsm888
To do this, you need to configure samba or NFS on the router. How to read in the internet, here Well, or you will find

Rep: (55)
* Nun70 Thank you, understood. It seems simple. Soon I take, I hope not to regret)

Rep: (0)
* Nun70 , not that not at all. In the explorer, both the computer and the laptop are displayed, I just can not configure access - I assume that the problems in the services still have no time to figure it out. And the router is visible, but it is not visible that a disk would be connected to it.

Rep: (286)
* Anastezija
Archer C7 - Discussion (Post NuN70 # 70474419)

Rep: (0)
Good day to all
please tell me this device can work as an access point (without NAT and DHCP)?
On ofsayte and manuals it is written that in order to make it work as an AP you need to disable DHCP. What happens with NAT is not very clear.

Post has been editedidle_r - 19.02.18, 11:35

Rep: (286)
* idle_r,
Well, do not use wan and dhcp will be taken from the server on the network. If you flash custom firmware, then you can wan to configure in lan.

Rep: (7)
NuN70 @ 02.19.18, 18:48*
If flashing custom firmware
What for example?

Rep: (22)
idle_r @ 02.19.18, 11:33*
please tell me this device can work as an access point (without NAT and DHCP)?

Attached Image

Post has been editedJapet - 19.02.18, 14:18

Rep: (0)
NuN70 @ 19.02.18, 12:48*
Well, do not use wan and dhcp will be taken from the server on the network. If you flash custom firmware, then you can wan to configure in lan.

Do not use the WAN port is an elegant solution. o.O

Post has been editedidle_r - 19.02.18, 14:45

Rep: (286)
* idle_r,
If you don't need nat, why do you wan?

Rep: (0)
there is a network WD My Cloud; everything works fine; the network through Archer C7 is only when copying movies to a network speed from a computer, more than there are no pictures, help to tweak

Rep: (286)
* shmon1976
The speed for 100M / bit is normal. You have to have a gigabit ezernet on both devices, or in the case of wifi, there should be gigabit on the cloud and wifi 5Ghz c AC on your computer

Rep: (0)
Nun70 please tell me which one lede I ask you to install it now, from the selection on the screenshot, what's what? I have a subject like you v.2.
Shl. If it can be a little more detailed, is the preparation of a subject necessary or can it be rolledlede From under stock, is it possible to roll back and what exactly?
ZYY. In the cap would be your answers, thanks in advance very much: blush:

Attached images
Attached Image

Rep: (286)
I sewed this ->archer-c7-v2-squashfs-factory.bin.
Is there some moreEU european version, american US and israeli IL . Sew depending on version C7.
Shil immediately from the stock firmware. Further it will be possible to update throughsysupgrade firmware.

PS: With this firmware you can roll back to the drain directly from the web of the muzzle of any custom firmware:
Attached MB)

Post has been editedNun70 - 20.02.18, 19:37

Rep: (0)

Attached images
Attached Image

Post has been editedYNUSSIRIUS - 20.02.18, 19:03

Rep: (3)
Hello! Please tell me what is the difference between the versions and which one is better to take? As I understand it, on v2 is more than the range of firmware, but it is older. There is also v5 but no information on it at all. Are the improvements in versions 4 and 5 worth choosing and sacrificing the choice of firmware?

Rep: (22)
* ralgis

Looking for what you router.
If for flashing - look for v2, of course.
And if you set it up and forget it in the closet, any revision will completely come down.

Rep: (286)
* ralgis
There are also firmware for v4

Full version    

Help     rules

Time is now: 25/10/20, 8:32