Archer C7 - Discussion | Wi-Fi Router



Rep: (3)
TP-Link Archer C7 (AC1750 Dual Band Wi-Fi Gigabit Router)- Discussion
Wi-Fi Router 802.11a / b / g / n / ac | 2.4GHz frequency (450Mbit \ s) | 5GHz frequency (1300Mbit \ s) | LAN 4x1000Mbit \ s | USB 2x2.0 type A |

Attached Image

The forum decided to post images under the spoilerPicture

Specifications
HARDWARE CHARACTERISTICS
Interface 4 LAN ports 10/100/1000 Mbit / s
1 10/100/1000 Mbps WAN port
2 USB 2.0 ports
Buttons WPS / Reset Button
Wireless on / off button (wireless on / off)
Power On / Off Button
External power supply 12 V DC / 2.5 A
Dimensions (WxLxH) 243 x 160.6 x 32.5 mm
Antenna type 3 removable 5 GHz antennas with 5 dBi gain (RP-SMA)
3 internal 2.4 GHz antennas

PARAMETERS OF WIRELESS MODULE
IEEE 802.11ac / n / a wireless standards for 5 GHz frequency
IEEE 802.11b / g / n for the 2.4 GHz frequency
Frequency range (receive and transmit) 2400-2483.5 MHz
5150-5350 MHz
5 GHz transmission speed: up to 1300 Mbps
2.4 GHz: up to 450 Mbps
Sensitivity (reception) 5 GHz пјљ
11a 6 Mbps -96 dBm
11a 54 Mbps: -79 dBm
11ac HT20: -71 dBm
11ac HT40: -66 dBm
11ac HT80: -63 dBm
2.4 GHz
11g 54M: -77 dBm
11n HT20: -74 dBm
11n HT40: -72 dBm
EIRP (Wireless Power)<20 dBm or<100 mW
Wireless functions Enable / disable wireless broadcast, WDS bridge, WMM, wireless connection statistics
Wireless Security Encryption Modes: 64/128-bit WEP, WPA / WPA2, WPA-PSK / WPA2-PSK

CHARACTERISTICS OF SOFTWARE
QoS (data prioritization) WMM, bandwidth control
WAN connection type Dynamic IP / Static IP / PPPoE /
PPTP (Dual Access) / L2TP (Dual Access) / BigPond
Management Access Control
Local management
Remote control
DHCP server, client, list of DHCP clients,
address reservation
Port Forwarding Virtual Server, Port Triggering, UPnP, DMZ
Dynamic DNS DynDns, Comexe, NO-IP
VPN traffic pass PPTP, L2TP, IPSec
Access Control Parental Control, Local Management Control, Node List, Scheduled Access, Rules Management
Network security (firewall) Protection against DoS attacks, SPI firewall, filtering by IP address / MAC address, domain name, binding by IP and MAC address
Protocols Supports IPv4 and IPv6
Shared via USB Support Samba (storage device) / FTP server / media server / print server
2.4 GHz guest network guest network
one 5 GHz guest network

OTHER
CE, FCC, RoHS certification
Package Archer C7
3 removable antennas
Power adapter
Ethernet cable
Quick Setup Guide
System Requirements Microsoft Windows 98SE, NT, 2000, XP, Vista в„ў or Windows 7, Windows 8 / 8.1 / 10
MAC OS, NetWare, UNIX or Linux
Environmental Parameters Operating Temperature: 0 в„ѓ - 40
Storage temperature: -40 в„ѓ - 70 в„ѓ
Operating Humidity: 10% - 90%, without condensation
Humidity during storage: 5% - 90%, without condensation
Firmware
Dumps
Useful


Post has been editedninja88 - 29.10.20, 19:23
Reason for editing: Dump Archer c7 v5



Rep: (8)
Chapp @ 15.10.20, 1:40*
OpenWRT 18.06 ... got up without problems, 3G modem picked up

Why do you need OpenWRT when the rooter is better, since all modules are standing and configured for the modem, TiSt firmware is already the head of the wholeness for use with modems



Rep: (8)
Chapp @ 15.10.20, 1:40*
Now installed through the web interface OpenWRT

On the Rooter website downloaded the firmware for Archer C7 Ver 5 there in the instruction said
  • WHEN FLASHING FROM THE FACTORY FIRMWARE Use The Image WITH "FACTORY"
    in its name.

    WHEN UPGRADING ROOTER TO A NEW VERSION USE THE Image WITH "UPDATE"
    In ITS Name Only

If I'm not mistaken, you need to put Factory but when I try to pour it through the interface, the router does not put it.
I need to rename it ?? To install.



Rep: (2)
* moby010, Rooter is good .. Modems clings without problems. It is made on the OpenWRT database and therefore, if OpenWRT is installed, you can immediately fill up the Update Rooter firmware from the web interface that I did. I just restored the router after squeezing (after the firmware of the old DDWRT from the header and apparently at some stage, the article is a section) and I already stood OpenWRT.
And in Rooter I still see that the LEDs do not display the connection of the USB modem and the availability of the Internet, although everything works. (maybe it is configured somewhere?)

Post has been editedChapp - 15.10.20, 06:53



Rep: (8)
Chapp @ 15.10.20, 8:45*
If OpenWRT is installed, you can immediately fill Update

Well, and you can immediately fill the rooter firmware without filling OpenWRT, and even how to pour the OpenWRT firmware through the web interface or through the program?



Rep: (12)
Dump Archer c7 v5



Post has been editedsir90 - 15.10.20, 08:02



Rep: (12)
If someone knows where the Syrian and at what address is written to write



Rep: (2)
Moby010 @ 15.10.20, 08:06*
Well, and you can immediately fill the rooter firmware without filling OpenWRT, and even how to pour the OpenWRT firmware through the web interface or through the program?

Well, in general, in the idea of ​​the factory firmware, you must first put the "Factory" file from the web interface, and then install "Update" from there. Why factories is not placed from the web interface of the factory firmware - I do not even know.
By the way, the same instruction is written for DDWRT. I did so according to the instructions (the files took from the header), Factory was fine normally, and during the UPDATE firmware something went wrong and I was waiting for fun days and nights)). So you can flash the Factory OpenWRT firmware from the web interface and then click from there to flash update from Rooter. The problem in the Factory firmware DDWRT, which is specified in the header - it turns off the RESET button and then it is not necessary to make FTTP Recovery. I hope in other Factory firmware such a paddown is not provided.) But even if so, then won the good people dump posted .. it will be possible to restore through the UART.

Posted on 15.10.2020, 16:46:

SIR90 @ 15.10.20, 09:42*
If someone knows where the Syrian and at what address is written to write

And what is the serial there? It is necessary to know it to find .. And how did Full-Flash dump be removed from the router with a famous serial to find it there?



Rep: (8)
Chapp @ 15.10.20, 18:42*
OpenWrt firmware

In short, I flooded Rooter according to the OpenWRT instructions via FTTP



Rep: (286)
Question to those who stitched Breed on Archer C7 V2. What kind of Breed poured and how.



Rep: (18)
I sewed according to the instructions in this threadhttps: //forum.openwrt....-OverClock/9757? Page = 4. When accelerating AHB, 380MHz seems a bit too much. Then I put a divider from memory to 2 (760 / (2 + 1) = 253), so it seems more stable. Month 1GHz stable and without clock drift. In the datashet on QCA9558 it is said that the AHB frequency affects not only on USB, and also on SPI (ROM) ... who in this regard experimented and tested - write off

Post has been editedtreatorc - 23.10.20, 17:35



Rep: (12)
Help guys, the head is not cooking already
If the firmware is removed, and the recovery of the dump you can change the password of Wifi and poppy addresses, (and the last two signs of the poppy change and the name of the WiFi network).
But at the same time, if the router is already registered by the client in the cloud service TP Link, then further users restored their router through the pouring of the dump from such a router will be unavailable.

Attempting to shift the poppy address, it is also not crowned with success, since in the Cloud Service tab will write "Page is not available."

The only correct solution is to restore the poppy + serial

Compare two dump and found where it is registered:

dev_id:
800095E5C7C5EA670EG0EED8331F0B571D08E816.
And serial himself: 22031w1002939

Need to be decrypt: ((

With that, the second dump serial also starts at 800043c0278cea3c8147dc02614433561be21f03

Post has been editedsir90 - 20.10.20, 04:45



Rep: (18)
Treatorc @ 17.10.20, 23:49*
When accelerating AHB, 380MHz seems a bit

Yes, with a rollback to 253 MHz, the logs stopped swearing on the AdBlock and the overflow of memory went. Mistress note!)

Post has been editedtreatorc - 21.10.20, 22:03



Rep: (87)
Guys, the power of transmitters does not cut?



Rep: (18)
I do not think. The main thing is the section Backaging and take care ...

Post has been editedtreatorc - 23.10.20, 17:36



Rep: (53)
* oykc777,
Depends on the settings ...

* sir90,
Print vir_id "from the bald" tried?



Rep: (12)
* Spec_spb , no, as I need old you need to restore



Rep: (53)
* sir90,
And where did info come from that:
Is Mac + serial?
there _To_ Mac + serial ??
What are they there at all ???



Rep: (12)
* Spec_spb , infa after analyzing several dumps, but how encrypted xs first thought in MD5 but you



Rep: (53)
SIR90 @ 25.10.20, 12:52*
infa after analyzing multiple dumps

IMHO is a very bold conclusion ...
.. But - good luck in decoding .... because Only the sea are conquered;)



Rep: (87)
Spec_Spb @ 24.10.2020, 13:18*
Depends on the settings ...


I put on the maximum on the manual from the DDVRT forum, the signal is more powerful on the drain. Returned to stock.


Full version    

Help     rules

Now: 05.12.20, 17:12