TP-LINK TL-WR842ND - Discussion | [wifirouter] Discussion, firmware, problem solving
TL-WR842ND user guide.rarHello, tell me what to do. Sew on LEDE 17.01.4 / Trunk V3, now I can not get into the router. at 1.1 and 0.1 does not go
11111aleksey11111, Yes you open Putty and connect on 192.168.1.1 ssh.
In the trunk there is a web muzzle. Why do I sew nepoymi that, and then try to connect not understand what protocol and do not understand why
11111aleksey11111 @ 12.07.20, 14:53
that will give me the putty?
A vebmordu not put on the ssh does? In google bunch of instructions, but I repeat again
opkg update
opkg install luci
11111aleksey11111 @ 12.07.20, 14:53
that will give me the putty?
Will be able to: go to the router, configure the Internet, doustanovit luci commands above, then you will use web-muzzle.
11111aleksey11111 @ 12.07.20, 16:22
It does not go through the putti by 1.1
0.1 too? With addresses all right? Come with SSH?
If it does not, it is better to rollback to a drainhttp:? //forum.tp-linkru...wtopic.php f = 25 & t = 7469and then sew the right to luci.
Post has been editedReii - 12.07.20, 16:39
Reii At 0.1, too. Everything is done properly. According to the instructions. Not everything comes andHello to all! Prompt as me to flash the router tp link 842 nd v.1 least for some firmware to work with Huawei E3372h-153 modem
I tried two patches: one from solalex1 lede-go3-wr842n-v1-28082017 of the cap threads, the second also lede latest version for my router.
Tried two options:
Through the web interface - it gives an error 18001
Through tftp - loading goes to 100%, in the router, no changes in the log is
I tried two patches: one from solalex1 lede-go3-wr842n-v1-28082017 of the cap threads, the second also lede latest version for my router.
Tried two options:
Through the web interface - it gives an error 18001
Through tftp - loading goes to 100%, in the router, no changes in the log is
Connection received from 192.168.1.86 on port 3286 [14/07 00: 15: 21,770]
Read request for file<wr842ndv1_tp_recovery.bin>. Mode octet [14/07 00: 15: 21,770]
OACK:<timeout = 5,> [14/07 00:15:21.771]
Using local port 54403 [14/07 00: 15: 21,771]
WARNING: Last block # 15873 not acked for file<wr842ndv1_tp_recovery.bin> [14/07 00:16:13.459]
<wr842ndv1_tp_recovery.bin>: Sent 15872 blks, 8126464 bytes in 52 s. 6 blks resent [14/07 00: 16: 13,459]
Read request for file<wr842ndv1_tp_recovery.bin>. Mode octet [14/07 00: 15: 21,770]
OACK:<timeout = 5,> [14/07 00:15:21.771]
Using local port 54403 [14/07 00: 15: 21,771]
WARNING: Last block # 15873 not acked for file<wr842ndv1_tp_recovery.bin> [14/07 00:16:13.459]
<wr842ndv1_tp_recovery.bin>: Sent 15872 blks, 8126464 bytes in 52 s. 6 blks resent [14/07 00: 16: 13,459]
extasy1987 @ 14.07.20, 10:27
Prompt as me to flash the router tp link 842 nd v.1 least for some firmware to work with Huawei E3372h-153 modem
At the moment you sink (factory) firmware is loaded?
The most logical to try ithttps://www.ofmodemsandmen.com/firmware4.htmlif you do not wish to put the packages for the USB-modem
For firmware Photo via web use * factory.bin his own rename it wr842ndv1_tp_recovery.bin for firmware with tftp
Hopefully with the version of the device does not mess up anything.
(*second too lede latest version for my router)
[/ Quote] You can clarify exactly what is pierced? From here?https://openwrt.org/toh/tp-link/tl-wr842nd
Post has been editedMr. Crank - 14.07.20, 13:09
Mr. Crank @ 14.07.20, 09:50
At the moment you sink (factory) firmware is loaded?
Loaded, no changes since my actions did not happen.
Mr. Crank @ 14.07.20, 09:50
if you do not wish to put the packages for the USB-modem
I would not like the packages never set.
Mr. Crank @ 14.07.20, 09:50
For firmware Photo via web use * factory.bin his own rename it wr842ndv1_tp_recovery.bin for firmware with tftp
Done everything you've written one to one, but through the web - a mistake, and a tftp visually passes loading, but in fact nothing has changed
Mr. Crank @ 14.07.20, 09:50
Hopefully with the version of the device does not mess up anything
I hope not.
On the back of the router 842ND v.1
Mr. Crank @ 14.07.20, 09:50
You can clarify exactly what is pierced? From here?https://openwrt.org/toh/tp-link/tl-wr842nd
Yes, firmware took away
http: //downloads.openw...1-squashfs-factory.bin
Mr. Crank @ 14.07.20, 09:50
Hopefully with the version of the device does not mess up anything
A web interface version of this device
 |
Greetings, acquired 842ND v1, wanted to use a whistle E171. Like as officially potderzhivayu. However, paragraph 3 / 4G nowhere! Shall not sew? If sewing is what? In order not to suffer, we need a weak but stable speed cable.
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement