Dolby ATMOS | Equalizer from Dolby Labs
DA_R6.5.zipk2kot @ 25.06.19, 17:22
whether it is possible somehow to raise the bass (or any other slider) so that it does not pull away immediately, and that others are not moved up behind him?
In the built-in Dolby overload protection (as it is called exactly do not remember). This has already been mentioned several times in a branch. That it does not allow to raise the bass to the desired level.
There is a "trick" has upomenaemaya in a branch that I use.
The second slider from the lower bass is low, and the first slider bass to deliver higher. Then the bass, though of little drops, but all the same not so much.
Attached images
 |
Post has been editedAndersen-21 - 21.09.19, 04:37
Greetings from kogonibud turned it on 9 Androyd run? Through TWRP crash when you run through Magisk (17.1) of any icons in any ustanovennyh modules! I took fromHere
Post has been editedAlexeykamensk - 27.06.19, 22:54
Post has been editedAlexeykamensk - 27.06.19, 22:54
Alexeykamensk Yes, of course I have installed and running. 9 android. Magisk 19.4 canary. installed this through Magisk.  |
 |
 |
Alexeykamensk, This is done after installing the system, that is, how to put the firmware went into it, and then in tvrp shote Dolby usually flies due to the presence of some sound mods
Who works in the Redmi 7 (Magisk 19.3) I continually crashes at startup (on the installation after flashing ... question? After a firmware ???) I just bootloader unlocked phone after the reset are clean
Custom firmware not sew the principle
Custom firmware not sew the principle
Good day! In the presence of PG in the car (see. The signature), the sensor without physical buttons. Prompt working module Magisk to no manipulation of pressing the volume buttons. Thank.
Posted 06/28/2019, 8:03:
this version ?
Post has been editedWeddnessday - 28.06.19, 08:09
Posted 06/28/2019, 8:03:
# SanГ«kk @ 06/28/19, 1:28
I established this through Magisk.
this version
Weddnessday @ 28.06.19, 10:00
without manipulation of pressing the volume buttons
Post has been editedWeddnessday - 28.06.19, 08:09
Grom_Cell @ 28.06.19, 10:02
Atmos designed to magisk 18 and below
I could not start the Dolby DotOS 3.0 on any of the presented to the cap for 9 androjda, changed the firmware on HavocOS_2.6, flashed into TWRPSoundmod_Cleaner.zip (124,63 KB)to completely remove MusicFX and established through Magisk 17.1 here this[Oreo-Pie] Dolby Digital Plus_v.4.0- [UNiTY] [Light] _by_repey6-20190214.zip (6,48 MB)I wound up and running :)by firmware, too much depends!And after that[Oreo-Pie] Dolby Digital Plus- [UNiTY] [Light] _by_repey6-20181123.zip (3,66 MB)the top of the post to send in Fastboot Recovery System & Data (well, we are not afraid backup there :))
Post has been editedAlexeykamensk - 01.07.19, 19:05
Post has been editedAlexeykamensk - 01.07.19, 19:05
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement