TP-Link TL-WR1045ND - Discussion | [Wifirouter]
zdenis821014, What speed? I have wi-fi at the drain worked very badly. With DD-WRT no complaints. What sewed?
Fair_boy , Speed ​​of download and upload of wi fi. If earlier it was 49Mb and 46Mb, after flashing was 18Mb and 14Mb. Shilsya transition insertion of a cap and subsequent site DD WRT version v.3.0 [Beta] Build: 40559 Posted on 03/06/2020, 12:24:
Fair_boy , Attached images
 |
zdenis821014, Well, I have the same. I can say that 14 luchsche but steadily than 50 unstable.
I vayfay almost did not work at the drain.
Hi all! Please help solve the problem long endured, which is shorter than the situation panel house, near the PC should a router in another room where it stands 10 meters curling iron and a TV, the rate of Mbit / s: 250. but it outputs to check for curling detonation 1.2 2.2 Mbit / s. Sometimes even the neighbor quickly finishes off the top floor than my .. What is it can be? Or is it the router itself is so weak? That is to check now shows the phone spidtest right next to the router 32.1 34.5. Please help what to do?
Photo TL-WR1045ND v2
Hello! Help please with photos and diagrams for the device. Decided on their own to flash the router and as a consequence when desoldering demolished winbond25q64fvsig smaller components around the chip. Chip then turned to flash, but the component that demolished could not be found. Help opzhaluysta!
Hello! Help please with photos and diagrams for the device. Decided on their own to flash the router and as a consequence when desoldering demolished winbond25q64fvsig smaller components around the chip. Chip then turned to flash, but the component that demolished could not be found. Help opzhaluysta!
Good evening,
Please help with this problem: Route 1045nd ver.2 00000000 (software version 3.15.30 build 140905 rel.63539n)
Wi-fi works through it all konekt and web interface and online you can go, butLanports are not working .... no one at the start of the router are lit (type test), and then do not blink ...
on the web interface writes in Lan: Mac address of the IP address have there .... ... The subnet mask is ...
Probyval different cables in different Nout (to cut network card) is reset to the factory or anything.
Conder all integers not inflated.
What to do, and the trouble)))
Post has been editedmax-stile - 04.04.20, 19:17
Please help with this problem: Route 1045nd ver.2 00000000 (software version 3.15.30 build 140905 rel.63539n)
Wi-fi works through it all konekt and web interface and online you can go, butLanports are not working .... no one at the start of the router are lit (type test), and then do not blink ...
on the web interface writes in Lan: Mac address of the IP address have there .... ... The subnet mask is ...
Probyval different cables in different Nout (to cut network card) is reset to the factory or anything.
Conder all integers not inflated.
What to do, and the trouble)))
Post has been editedmax-stile - 04.04.20, 19:17
ArchiDez @ 27.11.17, 22:35
Here, try this, do not forget to unzip current)
strange that in this model there is no Bethke, as well as among the stable, why have ceased to be interesting to update at this router logs?
Good day. I'm worn out with this router. Use it in tandem with tp-link t4uh v.1.
Constantly catching disconnects. On a smartphone similar problem. Significantly as a few seconds lost internet and nothing is loaded. Faced with someone? Firmware default ', 3.16.9 Build 150,520 Rel.43758n
Constantly catching disconnects. On a smartphone similar problem. Significantly as a few seconds lost internet and nothing is loaded. Faced with someone? Firmware default ', 3.16.9 Build 150,520 Rel.43758n
Fair_boy @ 26.03.20, 11:01
Put away
TP-Link TL-WR1045ND - Discussion (Post by ArchiDez # 67525424)
TP-Link TL-WR1045ND - Discussion (Post by ArchiDez # 67525424)
This firmware is possible to make the repeater router, well, or a bridge (WDS) with wifi? If not, what was put to the repeater? Thanks in advance.
I'm sorry, but - somewhere vaguely heard that on some routers can be something somewhere to register, willows YouTube will not be advertising (such as the router itself will Bloch with ad server data). This can be done on the drain insertion, and if da how?
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement