1. Download and install the latest version of Samsung Kies
from here. If you have already installed Samsung Kies and has been updated, skip this step.
2. Connect your phone to the USB-port home computer via cable.
Important : Use the original cord that went along with the phone. When using low-quality connectivity, the phone will not be detected, and even worse - you might not be flashing.
3. Run the Kies. Make sure that the program has found the phone and all install the drivers. On your computer, the list of devices and verify that the list is not unknown devices.
4. Make Kies in exports in the tab Import / export of all that you hold dear.
5. If you have set the root phone Titanum
from here. Make with the help of this program, a backup on an external memory card. Copy backup to your PC, just in case. In the absence of root can skip this paragraph.
6. Disconnect your phone from cable.
7. Now prepare for the firmware. Download everything you need:
- Odin program. Take the cap of the subject.
- Trohfaylovuyu service firmware. Take the cap of the subject. We need to take within its version. That is, if you have a 4.1.2 or 4.3, then take or 4.1.2 or 4.3, depending on the one that you have installed.
It is strictly forbidden to use firmware version 4.0.4 as firmware version of the SDS cause a failure of internal memory, which leads to damage to the phone and need to contact the service center to replace the motherboard.8. Unzip all downloaded files (if this zip- or rar-archive, tar unpack do not need!) To the appropriate folders. Sometimes together with the firmware files can go Odin 3.04 files and file SS.dll - they can be removed. After unpacking the firmware you should have a file with the extension * .tar.md5. If you get other files - you have unpacked the firmware properly.
Important. The path to the firmware should not be Cyrillic, you have a folder with the unpacked archives must have an English name, and is preferably in the root directory. 9. Perform a full reset of the phone, if you have the opportunity. For this mode, type the following dialing * 2767 * 3855 #, or via the phone settings "Backup and reset" - "Factory data reset".
10. Turn off your phone. Wait until the logo disappears on the screen and turn off all the buttons. After unsuccessful flashing simply remove the battery and put it back.
11. Put the phone in download-mode. To do this, simultaneously press the volume down button В«HomeВ» button and turn on the phone.
12. Connect your phone to the computer again. The device should be detected and installed one additional driver. Make sure the device is connected normally as in step 3.
13. Close the main window Kies. Open the Windows Task Manager via Ctrl-Alt-Del, tab "Processes", sort them by name, and complete all the processes that start at the name on the "Kies". It is advisable to disable the anti-virus program on your computer.
14. Start the Odin.
15. Below the gray box in the line В«ID: COMВ» port should appear inscription on which Odin found the phone. If the label does not appear - Odin does not see the connection: something with a cord or the driver is not installed. Check.
16. If the phone is found, then sew trohfaylovuyu service firmware from the folder where you unzipped it. To pray in the Odin window, select:
- If the firmware folder is a file with the extension * .pit - select it in paragraph PIT-Loader. The latest versions of the service firmware file with the extension * .pit may lie in a file, in which the title has the word В«CSCВ», it can be seen in Total Commander, and if there is a markup file, you can skip this step, all done automatically.
- If the folder is a file with the firmware, in the name of which there is the word В«BOOTLOADERВ» (in our case it will be a firmware chetyrehfaylovoy service) - select it in Bootloader point.
- If the folder is a file with the firmware, in which the title has the word В«MODEMВ» (in our case it will be a trohfaylovoy chetyrehfaylovoy service and firmware) - select it in the item PHONE.
- If the folder is a file with the firmware, in which the title has the word В«CSCВ» (in our case it will be a trohfaylovoy chetyrehfaylovoy service and firmware) - select it in the CSC point.
- If the folder is a file with the firmware, in the name of which there is the word В«CODEВ» (we have it will be in all firmware versions) - select it in paragraph PDA.
Attention : Firmware should contain at least the file!
- Make sure that there are crows Auto Reboot and F. Reset Time. If the firmware is included with the file extension * .pit - and you have chosen it, as described above, jackdaw Re-Partition will turn on automatically. Otherwise, it is not necessary to include.
17. Once again, recheck all settings. Firmware - a sure way to turn a phone into a "brick", if something is confused!
18. Press the Start button.
19. If there has been hovering at the stage of В«Setup connectionВ», after which the program generated В«FAIL!В» - should not be afraid. If this does not work - you have problems with a cord. Exit Mode download-possible by pulling the battery out of the phone and inserting it back in 10 seconds. Because actually the firmware has not been implemented - nothing bad will happen, everything will remain as it was.
Attention: In no case do not leave Odin Odin, or disconnect the phone from the cord and do not pull out the battery if the process has gone further than the В«Setup connectionВ»!
20. If the firmware to run properly - wait for its completion. It usually takes less than 5 minutes. By the end of the phone firmware reboot - you can disable it from the cord.
21. Close the Odin.