Rep: (13)
* Last1SiN , Thanks for the tip, figured out! It turns out really a broken image, pumped it and everything became without any problems! Although the hams of the sum rechered! Now I am with Russian!



Rep: (13)
* Last1SiN , So the meaning? How he will install the region you need if the image is not unpacked ...



Rep: (13)
* Last1SiN , Yes...



Rep: (13)
* Vulpes-vulpeos, So I did not understand! In general, after the item "Press (a) to allow an entry into SYSNAND (LVL2) and enter the specified button combination", I knock out the error "Line 207: Mount Fail Imgmount $ [Ctrnand]". What am I doing wrong? Rocked the first image "New 3DS OR 2DS - 11.5.0 - EUR - CTRTRANSFER", two files from the archive snapped into the in folder on the map ...



Rep: (13)
Hello everyone! Recently wrote that I want to change the region onNEW 3DS.. What would I do this, you need to transfer Emunand in SYSNAND, that's just how to create this emunand? If I'm wrong, correct! I will be glad any help! The console is already stitching ...



Rep: (13)
* McPcholkin , Thank you, I will study.



Rep: (13)
* McPcholkin I found only this https://3ds.customfw.xyz/lumalocales
But there is a change in the region, but how to change the system language is not found. Poke your nose, if not difficult ...



Rep: (13)
Hello! Tell me, have a familiar 3ds American. After reading a bit learned that the only region in the games can be changed, that they were in Russian. It may still have a programmatic ways to change the system language to Russian?



Rep: (13)
* Narcosis-doom , Drive itself workers, problems with lens. I have another snag, the previous console was version 1.1, the BIOS in the chip will flash under it. Most likely this is the problem, because the drive is precisely a worker, on the previous console did the softmode from it.



Rep: (13)
So my cable came, while I can't say anything about them, as it does not work out from the disk.
Before soldering Chip, I decided to clean my box from dust and replace the paste. The benefit of dust was not much, the thermal staples were on the radiators, which the solvent was perfectly erased.

Pasta An Arcting Cooling MX-4.
Next, started soldering the pads and wires on the back of the board, I have ver. 1.6. Assemble, I launch Iiii, nothing, blinks the discovery indicator of the tray. It turns out I forgot the path to cut.
The prefix starts, Logo Evox is, but here's a new trouble! The drive of the native dead, on the left, there is no exactly working launch.

Attached images
Attached Image
Attached Image



Rep: (13)
* Sodya. , Impossible!



Rep: (13)
At the moment I order from Ali component and Wii HDMI, plus I will chip my prefix and put a hard amount. How everything comes and make a console, I will add to the header that, where and how I ordered, also accomplish your quality!



Rep: (13)
* Oven I, Deceived! Percent, all Har-ki on a photo . Something can cheaper advise? 1060 I understand this maximum for this project?

Post has been editeddigma19 - 31.10.19, 15:44



Rep: (13)
Hello everyone! Guys, please tell me, a friend burned the map, was HD 7850. Now you need a new one. The card is needed for percents I5 2400, mostly plays the tanks. What will advise under this percent ...



Rep: (13)
* UnderTr, White! I did not solder, but I regained! I will try to edit the contacts, it may help.



Rep: (13)
Hello everyone! SD2Vita came to me, with Ali, the SD card is not loaded with them. The prosperity did not help. Who faced with such cases? Maybe I'm not correctly removing? Or in their trash?



Rep: (13)
* Blackpanthera90 All learning begins in the header, there all diagrams are provided! The Russian language in the installation of the chip is not needed at all, everything is clear on the video, you need to solder a pair of wires, cut the track, to have a block and put a chip on it. Video by the way on the installation above the good thoroughly!



Rep: (13)
* Narcosis-doom Okay, thanks for the help, asking for the forums, anyone can tell you.



Rep: (13)
* Narcosis-doom , Error with full minced meat in spoiler! Even if the adapter is not working, this is another problem. The chipstock must in any case run the disk, without any difference from what drive! What is wrong with me? Well, what!?)



Rep: (13)
* Narcosis-doom In short, I tried different options, changed a loop, from 40 PIN to 80, rearranged the jumpers, but with an empty hard it starts!
That's what I have:

What is the problem, I can not understand at all! But with my native hard problem there is no problem!

Posted on 25/09/2019, 19:28:

* Narcosis-doom , The loop as you can see 80 pins, jumper on the drive in Slave, hard worker, checked on a PC, the adapter seems too.
The chip will flash on the support of the big hard, the EVOX logo is!
Native drive is completely dead!

Posted on 25/09/2019, 19:29:

* Narcosis-doom , I forgotten, driven from the console itself, bought a recent splitter.

Attached images
Attached Image
Attached Image
Attached Image
Attached Image
Attached Image

Full version

Help     rules

Now: 22.01.21, 05:12