Pavel1411,
Can.link to the pipe 60 fps
link pipe 4K

Posted 06/16/2018, 8:57:

A few examples of photos on the stock camera.



Post has been editedIce-kiling - 16.06.18, 09:10

Ice-kiling That the focus of walks, the drain is not such jerks. Camera 2api worth?

Pavel1411,
Wow. On the drain after the last update I have autofocus does not work, only to poke a finger. 2api not worth it.
Try playing with the settings, I will lay out a little later like the best.

Post has been editedIce-kiling - 16.06.18, 09:19

Ice-kiling Which camera filming these videos? Stoke or gcam?

lelikbolik1984,
Through Snapdragon Camera, stock can only 1080/30 fps.
neHcioHep,
There now lay out a couple of videos. I recorded in the drain chamber.
Here islink pipe SlowMotion

Post has been editedIce-kiling - 16.06.18, 10:02

I MIUI10 beta at the auto focus works fine! And Gcamera and the drain. 2api installed.

Ice-kiling , You can do a screen video settings in snapcam

lelikbolik1984,
There is a possibility that the problem is because the Snapdragon Camera Some settings do not work or work very strange. (Try to rearrange)



Post has been editedIce-kiling - 16.06.18, 10:29

Ice-kiling , Hmm .. I do not have such a snap camera and select the FPS is not. AIC can throw? I wrote to you in the LAN, you can not answer.

Ice-kiling Noticed that when you fps60 off stub. It should be?

lelikbolik1984,
Yes, it was. I've found that I have an old version was, when the stub he stabilized only on the phone, and could be removed only to the 30 \ s (so it was off). Now I put out caps and check again.

In short, the set of caps (snapdragon camera), some functions are beginning to work adequately. When stabilization 60 frames and the maximum available 1080 (read drain) when the disconnect removes at 60 and 90 on frames FHD and 4K by 30 frames.
Autofocus will have to test more to 60 frames.

Post has been editedIce-kiling - 16.06.18, 10:56

When, after the installation exhibit 60 fps snapdragon chamber pishit normal, sometimes it undermines. If you came out of the program, then you need to put the settings back again 60fps. After this write error. Work begins only after reinstallation!

Throw off version, which normally runs at 60fps FHD. And now to work, then does not work, then again gradually removed, right now, trying to write - 30fps

Pavel1411 , The version that 265 codec I normally works and 60fps too, one drawback - a little walk autofocus at 60fps, stabilization include not needed, it automatically uses the stub native apparently, and I also rented with an option tnr on, and cds off, so More noise in low light, but there is no soap in the light of norms.

PS In general, through the entire Internet in search of a stable version, but all or some schools that climbs or settings in 2 times smaller. Most standards proved to be a version with 265 codec from this thread. Can anyone find a better, try the latest version, it works without problems but there are almost no settings in comparison with that which I have now, how can they can activate xs, there is still done separately bokeh mode button

Post has been editeddixyl - 16.06.18, 11:34

dixyl , I also have a 265, but still writes in 30. Can your APK or version at least. (Or link)

Pavel1411 , Use the version with the caps, lecturing her back to previous page, please try the version with post Elemana like on page 45 was, but I have it crash all the time, maybe you earn

Post has been editeddixyl - 16.06.18, 11:40

dixyl I have even a picture becomes darker ... But no ... 60 FPS

You set 2api?

alhe No, because the other person is working without it. I immediately asked him this. And how it manages the 60 to write, and then broke))

Post has been editedPavel1411 - 16.06.18, 11:48

I have installed for Gcamera, but it does not write to 60fps, can this problem?