FAQ of general instructions and recommendations for Xiaomi devices
Install official firmware on the device with a locked bootloader
using XiaoMiTool or XiaomiADB
using XiaoMiTool or XiaomiADB
Method 1 - XMT
It is necessary:
Instruction
- XiaoMiTool program -
XMT_0.5.2.zip (87.67 MB) - The device in the mode:Recovery - Sonnect with MiAssistant
Instruction
- Download and install the program
- Go to the folder with the program and run a shortcutFastFlash
- In the flash selection is formulated as follows:
- The first two paragraphs are putting firmware type (eg Global Stable and Global Developer)
- The third point - None
- The fourth item - None
Chinese firmware oftenNOTfinds! - The first two paragraphs are putting firmware type (eg Global Stable and Global Developer)
- PushSelect
- Connect the device by selecting the item rekaveriMi assistant
- Once the device is determined automatically will download process and install the selected firmware
- At the end of a successful firmware upgrade, the device will reboot.
Method 2 - XADB
The main difference from the previous method, it is possible to sew already downloaded the firmware. But still passes validation servers.
Required
- Xiaomi ADB -XiaomiADB.zip(1.11 MB)
- Official firmware forRecovery \ System
- The device in the mode:Recovery - Mi Assistant
Instruction
- Download Xiaomi ADB and unpack on drive C;
- In the same folder to put the firmware archive;
- Connect the device in the modeSonnect with MiAssistant(Boot into rekaveri and select third paragraph);
- Drag the file with the firmware on XiaomiADB.exeoropen the console (in a folder to hold Shift and click the RMB, select "Open Command Window") anddial:xiaomiadb sideload_miui nazvanie_arhiva.zip
- When finished, the device will reboot;
In case of any errors after installation, it is recommended to format data, the command:
xiaomiadb format-data
Installing firmware with TWRP
(only for unlocked bootloader)
(only for unlocked bootloader)
- TWRP image from renamerecovery.img , Throw in a folder images firmware, replacing the stock rekaveri.
- The necessarybat file make changes to the text editor, a better Notepad ++ ( Besidesflash_all_lock.bat and flash_all_lock_crc.bat Or you will get a brick):
flash_all.bat- clean install
flash_all_except_storage.bat- rewrite data preservation
- Open a text editor, and in the end find a line like this: fastboot% * reboot
- Replaced by: fastboot% * boot% ~ dp0images \ recovery.img || @echo "Boot error" && exit / B 1
- Save changes.
- Flash modefastboot a command line or MiFlash.
- After closure, the apparatusautomatically reboot into TWRP , For its further use - in particular for installing the patch or kernel obtain Root.
How to create a backup of applications and data through ADB
(Ruth works without rights)
(Ruth works without rights)
Is required
- Platform-Tools
- USB debugging
- ADB drivers
Creating a backup
- Download Platform-Tools and unpack at the example of the path C: / adb
- connect the device
- Open a command prompt and type to be scanned (when a window with a request to allow connection):adb devices
- It turns out about the answer
- Next, enter the command to create a backup:In this case, backup application, the data cache in the OBB, application data on a memory cardadb backup -apk -all -shared -obb -f c: \ adb \ data.abIn this case, backup application, the data for iskyucheniem system applications, the cache in the OBB, application data on a memory cardadb backup -apk -all -shared -obb -nosystem -f c: \ adb \ data.abIn this case, only the data backupadb backup -all -f c: \ adb \ data.ab
- After that, the command line appears, that is required to unlock the screen of the device and confirm the backup. We allow.
- After graduating from the file's backup will be based on the specified path.
Recovery
adb restore c: \ adb \ data.ab
Adb run
All this can be done utility ADB Run -https://androidp1.ru/s...roid-i-vosstanovlenie/
Post has been editedDima_Apatity - 02.05.19, 01:00
Saving and restoring IMEI via QPST (Qualcomm)
Is required
I did everything without any Root rights.
 |
- Established QPST
- USB debugging
- Platform tools
Backup
- Translating device in the diagnostic mode
adb devices
# Check the connectionadb shell
# terminalOptionssetprop sys.usb.config diag, adb
# Translation device in diagnostic mode*#*#717717#*#*setprop sys.usb.config rndis, diag, adb
# Translation device in diagnostic mode - Run QPST Configuration
- If the device does not appear automatically, manually add: pressAdd New Port ... , Remove the check mark " Show Serial and USB / QC Diagnostic ports only "In two fields we register our COM-port, then click OK
- FurtherStart Clients -> Software Download
- In the window that opens, select the tabBackuppushBrowse, Specify a folder to save, as well as the type of stored files (xqcnorqcn)
- PushStart, Will the backup process. After which will beMemory Backup Completed
- backup created
Recovery
- Open the tabRestore, Specify the backup file
- PushStartand wait for the end of the process
Recovery, if there is no backup
This will require a donor file qcn your model, though with zeroed IMEI
And a small utility to change -QualcommIMEIRebuilder.zip(550.19 KB)
Editor xQCN files -XQCN_Editor_1.02.zip(280.37 KB)
And a small utility to change -
QualcommIMEIRebuilder.zip(550.19 KB)Editor xQCN files -
XQCN_Editor_1.02.zip(280.37 KB)- Run the utility and open the file * .qcn
- Instead of zero (or what there will be) their value is entered and pressRebuild
- Save the new file
- Restoring through QPST
Post has been editedDima_Apatity - 20.09.19, 19:29
Reason for editing: Files Editor xQCN
QCN files to restore IMEI
(IMEI zeroed)
(IMEI zeroed)
Mi
Mi_5_gemini.zip(149.1 KB)Mi_5S_capricorn.zip(160.14 KB)Mi_5S_Plus_natrium.zip(168.02 KB)Mi_5x_tiffany.zip(106.13 KB)Mi_6_sagit.zip(101.38 KB)Mi_8_dipper.zip(130.36 KB)Mi_8_Lite_M1808D2TG_platina.zip(109.85 KB)Mi_8SE_sirius.zip(85.76 KB)Mi_9T_davinci.zip(191.96 KB)Mi Max
Mi Mix
Mi Note
Mi_Note_16GB_virgo.zip(78.96 Kb)Mi_Note_64gb_virgo.zip(77.75 KB)Mi_Note_Pro_leo.zip(110.06 KB)Mi_Note_2_scorpio_2015211.zip(162.4 KB)Mi_Note_2_scorpio_2015213.zip(204.79 KB)Mi_Note_3_jason.zip(92.37 Kb)Mi A
Mi_A1_tissot.zip(103.86 KB)Mi_A2_M1804D2SG_jasmine.zip(119.24 KB)Mi_A2_Lite_M1805D1SG_daisy_sprout.zip(77.63 Kb)Redmi
Redmi_3_ido.zip(62.47 KB)Redmi_3s_land.zip(51.3 KB)Redmi_4a_rolex.zip(58.04 Kb)Redmi_4x_santoni.zip(68.93 Kb)Redmi_5a_Prime_ (MDE6S) .zip(70.09 KB)Redmi_5_rosy.zip(51.49 KB)Redmi_5_Plus_vince.zip(71.81 KB)Redmi_S2_ysl.zip(72.58 Kb)K20_Pro_Raphael_xQCN.zip(507.03 KB)Redmi note
Redmi_Note_3_kenzo.zip(79.17 Kb)Redmi_Note_3_SE_kate.zip(68.57 KB)Redmi_Note_4-4x_mido.zip(75.78 KB)Redmi_Note_5A_Lite_ugglite.zip(83.37 Kb)Redmi_Note_5A_Prime_ugg.zip(83.74 Kb)Redmi_Note_5_MEl7S_whyred.zip(122.76 KB)Redmi_Note_5_MEE7S_whyred.zip(132.01 KB)Redmi_Note_5_M1803E7SG_whyred.zip(127.46 KB)Redmi_Note_6_Pro_tulip.zip(121.28 KB)Redmi_Note_7_lavender.zip(132.74 KB)Redmi_Note_8_ginkgo.zip(133.91 KB)Other
Pocophone_F1_beryllium.zip(160.94 KB)Post has been editedvovcik3 - 06.04.20, 16:26
Reason for editing: Mi 9T and Redmi K20 Pro
The transition between the lock global firmware loader
(Example: with firmwareRuonMI)
It does not work on the new devices (from 2019)
It does not work on the new devices (from 2019)
A couple of words
Personally tested on devices Redmi Note 5 and Xiaomi Mi 9T, also works on other models.
Because three points of transition between global firmware is not possible, then there is an alternative method, without unlocking,at the time of writing the post.
During flashing, the process can "hang out" at 4.99% and 90.49%, do not worry.
Because three points of transition between global firmware is not possible, then there is an alternative method, without unlocking,at the time of writing the post.
During flashing, the process can "hang out" at 4.99% and 90.49%, do not worry.
Is required
- XMT v2 -https://www.xiaomitool.com/V2/
- The apparatus enabled Debug
- the Internet
Instruction
- Download, install, run the program. Choose your region. (I chose the natural Russia).
- Connect your phone, select an item to the operating device.
- When scanning in the case of the connection to allow the request. After that, the device appears in the list of found.
- After that, the device is handled in Fatsboot mode for reading the information required.
- Next boot rekaveri, which will have to selectConnect with MiAssistant
- In the next step, select "Official firmware Xiaomi", will search for available.
- Select the point with the necessary globalkoy, in this case, MI. Also there is an option to select already downloaded file.
- Warning thatdata will be deleted .
- Downloading firmware.
- By the end of the download, reboot rekaveri and connection modeConnect with MiAssistant To start the firmware installation process.
- Following which, greeting appears. And the device will boot with the new firmware.
Post has been editedcherva70 - 03.03.20, 20:14
Fastboot "Press any key to shutdown"
Such a mistake is very common in the new "iron" PC. And work with fastboot mode becomes almost impossible due to the constant "off" device.
If you encounter this error, it will install USB 3.0 controller via the PCI-E interface. USB Hub is not always able to solve the problem.
For example
 |
Thanks to the distinguishednamin78
Post has been editedDima_Apatity - 17.08.19, 12:57
Install TWRP in the presence of root-rights
TWRP App
Themeonsavagemessiahzine.com
- Install the application and run
- We agree with the points
- ChooseTWRP Flash , Giving Ruth rights, etc. Select a file to flash .. and specify the desired image rekaveri
- Stitching
- After installation can be overloaded in rekaveri
Flashify
Themeonsavagemessiahzine.com
- Install the app and launch, giving Ruth rights
- ChooseRecovery Image , Further Choose a file and specify the desired image rekaveri
- Stitching
- After installation can be overloaded in rekaveri
Brief guide to unlocking the bootloader
Minimum requirements
- MI account to link your phone number and and the presence of a SIM card with that same number
- Internet connection, both the sim card and the PC.
- Official utility to unlock
- Driver (if there is a folder with MiUnlock)
Unlock
- On the device, activate the Developer menu (Settings - About phone - several times Tapan MIUI Version). Go to the section.
- Choose "Status Mi Unlock "
- WITHenabled mobile internet click "Link account with the device"When you try to link via WiFi you will receive the following
- The idea from this point will the so-called "Counter" to unlock. To be sure, put the device in fastboot mode, connect to a PC and run MiUnlock.
Further
- In the utility agree and enter your account information (phone number or e-mail, or ID). Go check the resolution, which by the way have all accounts.
- Check identification device. If not detected, go to put the driver, change the ports, etc .. Also, see a warning about resetting the information on the model if it is.Then two more.
- Will unlock process
Counter
If on99%get an error, it is usually a counter after which it will be possible to unlock:
- Binding time is too short, Less than XX hours
- After XX hours of trying to unlock the device
- Please unlock XX hours later. Use your device actively while you're waiting
Run GPay on unlocked bootloader
Introduction
Actions performed on Mi 9T withglobal firmware, An unlocked bootloader, TWRP, Magisk.
- Install the patch from MiRoom -GooglePay_fix.zip(126.12 KB)
- The NFC settings expose "HCE Purse"
- In Magisk hide Ruth for GPay, Google Services, and banking applications
In principle, everything. GPay card adds, payment runs, the transaction is displayed.
Assistant while working with ADB, Fastboot, TWRP
A couple of words
Written small skriptik multiple manipulations in various modes. I hope it will be updated and supplemented.
For all suggestions, questions, etc. write in the QMS.This topicNOTfor discussion .
For all suggestions, questions, etc. write in the QMS.This topicNOTfor discussion .
Screen
Description
Adb
- Checking the connected devices, with the ability to restart in different modes.
- Also translated into diagnostic mode. 2 embodiment, since on the latest models has changed the team.
- connected device
- Check the code name of the device
- Various information about the boot loader, status for unlocked or not.
- ARB status check
- Flashing different images, such as the nucleus, rekaveri, regions, modems, splash. The folder structure I think it is clear that for nothing. For each item, with the image available to choose from the list. Rekaveri For example: in the appropriate folder, you can throw a few images (if your model is required to sew vbmeta.img, then he, too, put in a folder), and in the proposed list, select the desired image.
- So far, only possible to work with sideload mode to flash different files, also with a choice from the list.
- Saving, partition recovery Persisti EFS
- Mounting partitions
- Removing password lock screen
Changes
v 1.1
Fixed:
- after installing TWRP not everyone worked as a team to restart in rekaveri. Now, when an error occurs the launch image.
Posted in TWRP:
- mount partitions
- removal of the lock screen passwords
Fixed:
- after installing TWRP not everyone worked as a team to restart in rekaveri. Now, when an error occurs the launch image.
Posted in TWRP:
- mount partitions
- removal of the lock screen passwords
Download
Xiaomi_Helper_1.1.zip(2.69 MB)Past versions
Post has been editedDima_Apatity - 08.10.19, 16:38
Reason for editing: 1.1
M
Dear Sirs!
Locked for discussion. If you wish to add any instructions or add to existing ones, use the button
Locked for discussion. If you wish to add any instructions or add to existing ones, use the button
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement