Archer C2 (AC750) - discussion | [usbmodem] [wifirouter]: 300 Mbit / s Mb / s - 433 Mb / s Mb / s + 4x1Gb | 1 p
[email protected], 20:21
and what to do if wps does not light up?
Turn on the TFTPD prog, select the folder where the firmware was installed (well, the folder with the tftpd itself) and the main thing before launching the router, select its ip in TFTPD. And you just turn on the router with the wps button held down and I had to hold it for 10 seconds. The computer determined the router for a second, but if properly configured, it is enough for the program to pick up and install the firmware.
melihov07 , No, in my case it does not help, nothing happens, the router is dead, it is necessary to rustle the programmer.
In general, I revived the animal with the help of the programmerCH341A
But bought on Avito.
Connect the clip without soldering. The truth had to suffer, the contact at the clip is very fucking, while the programmer is plugged into the USB - the loop will move a little and the clip will be lost from the contacts.
Filled OpenWrt recovery firmware found like somewherehere
Post has been editedolegr1 - 23.04.19, 10:05
But bought on Avito.
Connect the clip without soldering. The truth had to suffer, the contact at the clip is very fucking, while the programmer is plugged into the USB - the loop will move a little and the clip will be lost from the contacts.
Filled OpenWrt recovery firmware found like somewherehere
Post has been editedolegr1 - 23.04.19, 10:05
Good evening, does anyone know how to set up a Rostelecom blocking bypass on a router, stock firmware
Zalman99, 1. You are wrong topic.
2. Firmware from Padavan, prohibited for distribution, except for brands of ASUS.
3. Download Prometheus, and collect it yourself. But if there is no support, then alas.
4. OpenVRT does not seem to support your router either.
5. Here you can either change the router or put a VPN on each device, etc. I can be wrong.
[email protected], 12:01
2. Firmware from Padavan, prohibited for distribution, except for brands of ASUS.
why?
Is it possible in any way to flash the device with the EU (the latest available firmware was flashed) with microcode with US firmware? In standard ways this is not possible.
By the way, my unit was originally US region. Up to a certain version of the firmware can be flash US version of the EU firmware and then go back but at one point (offsite pre-warned about it), I ask the new (at the time), EU version, back to the US to return has become impossible. Well, I stayed EU version of the firmware on the original router US. With this firmware ievropeyskimi began to emerge constant pshroblemy's zainteresovtsalsya if you can somehow return to the US firmware and try the last of them.
By the way, my unit was originally US region. Up to a certain version of the firmware can be flash US version of the EU firmware and then go back but at one point (offsite pre-warned about it), I ask the new (at the time), EU version, back to the US to return has become impossible. Well, I stayed EU version of the firmware on the original router US. With this firmware ievropeyskimi began to emerge constant pshroblemy's zainteresovtsalsya if you can somehow return to the US firmware and try the last of them.
[email protected], 09:41
why?
Well, when I studied the topic, I read about it very often.
If something has changed, ask Mil Sorry.
Good evening. If you need someone, then I offer you the "update" of the padavan firmware mod fromlinaro :)
Differences from the assembled firmwaremerage :
Commit: 56960f9
Sawed out:
Appearance settings (standard theme is active. No others.)
Added by:
OpenSSH, OpenSSL, FTP, SFTP
Instructions:
Attention: before upgrading Padavan, change the theme to the standard one, otherwise you will have to clean the cookies / cache, or the eternal page refresh will start on the web: D
I hope someone will find this useful;)
Post has been editedsasha0597 - 22.05.19, 20:04
Differences from the assembled firmwaremerage :
Commit: 56960f9
Sawed out:
Appearance settings (standard theme is active. No others.)
Added by:
OpenSSH, OpenSSL, FTP, SFTP
Instructions:
I already have Padavan
1. Download the file
update.zip(6.79 MB)
2. We pull out from the archive update.bin
3. Verify the hash of the update file..bin - MD5: D42AA9BD3D981EDCE878E20D087295D6
4. Go to the web interface of the router
5. Administration>Firmware update
6. Select the update file..bin and click send
update.zip(6.79 MB)2. We pull out from the archive update.bin
3. Verify the hash of the update file..bin - MD5: D42AA9BD3D981EDCE878E20D087295D6
4. Go to the web interface of the router
5. Administration>Firmware update
6. Select the update file..bin and click send
I have stock
There are 2 options:
1. Tftpd64 (instructionin postmerage ).
Archive:ArcherC2V1_tp_recovery.zip(6.84 MB)
MD5 hash:D6DC9A7C7F74C22D1BA08156F0B77B20
2. Sew programmer (archive line above: yes2 :)
1. Tftpd64 (instructionin postmerage ).
Archive:
ArcherC2V1_tp_recovery.zip(6.84 MB)MD5 hash:D6DC9A7C7F74C22D1BA08156F0B77B20
2. Sew programmer (archive line above: yes2 :)
Attention: before upgrading Padavan, change the theme to the standard one, otherwise you will have to clean the cookies / cache, or the eternal page refresh will start on the web: D
I hope someone will find this useful;)
Post has been editedsasha0597 - 22.05.19, 20:04
I have no relation to microticism under any condition. Both asusovskaya and open wrt.
Trying to configure it client + up.
Trying to configure it client + up.
ghl456 , you mean that Archer in AP client mode does not connect to the Mikrotik? If I understood correctly, then in my case everything works on Padawan. OpenWRT did not check.
By the way, it is very stable: smile:
Post has been editedsasha0597 - 24.05.19, 22:47
Sasha0597 @ 05.22.19, 08:31
Good evening. If you need someone, then I suggest you update the padavan firmware mod from linaro :)
Differences from the assembled merage firmware:
Commit: 56960f9
Sawed out:
Appearance settings (standard theme is active. No others.)
Added by:
OpenSSH, OpenSSL, FTP, SFTP
Instructions:
#
I already have Padavan
#
I have stock
Attention: before upgrading Padavan, change the theme to the standard one, otherwise you will have to clean the cookies / cache, or the eternal page refresh will start on the web: D
I hope someone will find this useful;)
Differences from the assembled merage firmware:
Commit: 56960f9
Sawed out:
Appearance settings (standard theme is active. No others.)
Added by:
OpenSSH, OpenSSL, FTP, SFTP
Instructions:
#
I already have Padavan
#
I have stock
Attention: before upgrading Padavan, change the theme to the standard one, otherwise you will have to clean the cookies / cache, or the eternal page refresh will start on the web: D
I hope someone will find this useful;)
But tell me, is there a dream in this beauty? regarding 3g modem, for example.
Or at least a reboot on a schedule.
Post has been editedghl456 - 29.05.19, 22:56
ghl456 , I did not quite understand what was meant by whatchdog for connecting via mob. network, but watchdog on the collapse of the kernel (hardware WatchDog) is present.
If you are interested in a reboot on a schedule, now I’ll stop by and check
upd: there are no separate features with a reboot, or I did not notice, but you can organize everything with a cron, the main thing is to be able to. On the Internet, everything can be found. The main thing in the endless reboot is not to send it: D all the same, time is lost.
Post has been editedsasha0597 - 29.05.19, 23:22
If you are interested in a reboot on a schedule, now I’ll stop by and check
upd: there are no separate features with a reboot, or I did not notice, but you can organize everything with a cron, the main thing is to be able to. On the Internet, everything can be found. The main thing in the endless reboot is not to send it: D all the same, time is lost.
Post has been editedsasha0597 - 29.05.19, 23:22
Sasha0597 @ 05.29.19, 12:13
what is meant by whatchdog
I mean that when the Internet fell off on 3G, the router reboots on power. Than distorts dongle.
ghl456 @ 05/30/19, 14:09
The router restarts on power. Than distorts dongle.
in order not to force the router, you can reset the power on the usb port.
usbreset_padavan_mips.7z(36.97 KB)Butaford @ 05/30/19 03:19
in order not to force the router, you can reset the power on the usb port.
Attached file usbreset_padavan_mips.7z (36,97 РљР‘)
Attached file usbreset_padavan_mips.7z (36,97 РљР‘)
possible for stupid manual how to screw this thing?
ghl456 @ 31.05.19, 14:11
possible for stupid manual how to screw this thing?
The most simple example, here is a script to run on the crown of every 5-10 minutes:
#! / bin / sh
HOSTS = "1.1.1.1"
COUNT_NEED = 4
DT = ".` Date '+% m% d% y-% H:.% M'` "
for check in $ {HOSTS}; do
count_real = $ (ping -c $ {COUNT_NEED} $ {check} | grep 'received' | awk -F ',' '{print $ 2}' | awk '{print $ 1}')
if [$ {count_real} -eq 0]; then
# 100% failed
echo "Host: $ {check} is down (ping failed) at $ {DT}"
# Command if failed
/ Usr / sbin / usbreset_static "Huawei Technologies Co., Ltd."
# or
# / Usr / sbin / usbreset_static 001/002
# or
# / Usr / sbin / usbreset_static 1a86: 7523
else
echo "Host: $ {check} success ping !!!"
fi
done
HOSTS = "1.1.1.1"
COUNT_NEED = 4
DT = ".` Date '+% m% d% y-% H:.% M'` "
for check in $ {HOSTS}; do
count_real = $ (ping -c $ {COUNT_NEED} $ {check} | grep 'received' | awk -F ',' '{print $ 2}' | awk '{print $ 1}')
if [$ {count_real} -eq 0]; then
# 100% failed
echo "Host: $ {check} is down (ping failed) at $ {DT}"
# Command if failed
/ Usr / sbin / usbreset_static "Huawei Technologies Co., Ltd."
# or
# / Usr / sbin / usbreset_static 001/002
# or
# / Usr / sbin / usbreset_static 1a86: 7523
else
echo "Host: $ {check} success ping !!!"
fi
done
usbreset utilityhere
Instead of a for loop, you can use a while loop, then run the script will need once at the start of the router
I check the Internet in some scripts like this:
echo -e "GET http://google.com HTTP / 1.0 \ n \ n" | nc google.com 80>/ dev / null 2>&1
if [! $? -eq 0]; then
if! ping -c1 8.8.8.1 1>/ dev / null 2>/ dev / null; then
echo "[!] There is no internet connection. We leave ..."
exit 1
else
echo "[*] The Internet is, but the problem is name resolution (DNS). We leave ..."
exit 1
fi
fi
echo -e "[*] Internet is."
if [! $? -eq 0]; then
if! ping -c1 8.8.8.1 1>/ dev / null 2>/ dev / null; then
echo "[!] There is no internet connection. We leave ..."
exit 1
else
echo "[*] The Internet is, but the problem is name resolution (DNS). We leave ..."
exit 1
fi
fi
echo -e "[*] Internet is."
In haste, do not kick
Post has been editedbutaford - 31.05.19, 14:30
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement