ZyXEL / ZyXEL Keenetic Start II - Discussion | [wifirouter]



Rep: (1038)
ZyXEL Keenetic Start II- Discussion
Keenetic Start (KN-1110) - Discussion
Attached Image

Information
Description
  • Product Name: Keenetic Start II
  • Part Number: EMG1300-T10A-RU01V1F
  • NDM HW ID: kl_rg
  • 5 dBi antennas of special design for better coverage
  • Any tariffs up to 100 Mbps
  • IPTV and Smart-TV support
  • Protection of Yandex.DNS and SkyDNS
  • Setup and control via mobileattachment

Additional photo
Specifications
Main characteristics

The processor - MediaTek MT7628NN (MIPS24Kc) @ 575MHz
RAM - 64MB (DDR2)
Flash memory - 8 MB (SPI)
Wi-Fi 2.4 + 5 GHz - Yes
Wi-Fi class - WiSoC 2T2R 300Mbps (2.4GHz)
Antennas - 2x 5dBi (fixed ext)
Ethernet Ports - 2x FE (10/100)

Wi-Fi / WPS button вњ”
Modes of access point, amplifier, adapter вњ”

Performance

2.4 GHz Wi-Fi network speed - 300 Mbps
IPoE / PPPoE Routing - Up to 95 Mbps
L2TP / PPTP Routing - Up to 95 Mbps

Functions and protocols

IPoE вњ”
PPPoE вњ”
PPTP вњ”
L2TP вњ”
802.1x
CABiNET вњ”
Multiple PPP Tunnels вњ”
PAP / CHAP / MS-CHAP / MS-CHAP v2 вњ”
MPPE (Auto / 40/56/128)
VLAN IEEE 802.1Q вњ”
Route Table (DHCP / Manual) вњ”
Link Duo вњ”
DHCP (client / server) вњ”
IPv6 Dual Stack вњ”
NAT вњ”
Igmp вњ”
UPnP
Manual port forwarding вњ”
PPTP / L2TP Transit вњ”
SPI DoS Attack Firewall вњ”
Ping checker вњ”

Wi-Fi wireless network

WEP / WPA-PSK / WPA2-PSK Network Protection вњ”
Support for additional guest Wi-Fi network вњ”
MAC access control вњ”
WPS Quick Setup вњ”
Wi-Fi Multimedia (WMM)

Applications

Mobile application for Android and iOS вњ”
UDP to HTTP proxy вњ”
IPSec VPN Client / Server вњ”
PPTP VPN server 10 tunnels
Internet filter Yandex.DNS вњ”
Parental control SkyDNS вњ”
Dynamic DNS client вњ”

Physical characteristics and environmental conditions

Device dimensions without antenna, W x D x H - 140mm x 103mm x 30mm
Mass device - 170g
Operating temperature range - 0-40 В° РЎ
Humidity of the ambient air during operation - 20% - 95% (no condensation)
Power supply - 100–240 V 50/60 Hz

Diagnostics and control

Web configurator in Russian вњ”
Command Line (CLI) by TELNET
The ability to control from the external network вњ”
Backup and restore configuration вњ”
Software update features вњ”
Logging system events вњ”

Equipment

Device
Power adapter вњ”
Instructions for use вњ”
Certificates
Documentation
Reviews, links
Useful information
Problem solving, setup
Enable 802.11n standard on NDMSv2 firmware (via CLI TELNET)
Forced assignment of N mode (compatibility N) for Wi-Fi via CLI from enpa
How to print from phone to printer via Android OS
Flash modem in HiLink for maximum speed
CAT5 HiLink Speed ​​Test
All about IP Cloud (KeenDNS)
Wake on Lan (WOL) function in ZyXEL Keenetic routers
A bit of theory on the mechanism of updating NDMSv2 firmware from _Danila_Master_
Wi-Fi signal attenuation coefficients when passing through various environments
How to change the network name of the smartphone in Android?
How to determine the type of antenna connector (SMA / RP-SMA)?
NTP SERVERS - time servers
Creating an ISP (Internet Service Provider) interface via CLI (command line) from enpa
If you need port 5 to distribute the Internet to devices on the wire from enpa
Speed ​​limit via CLI (command line) from enpa
PuTTY is a client program for working with network protocols SSH, Telnet, SCP, SFTP, for connecting via a COM port and ZModem, a utility for generating RSA and DSA digital SSH keys.
Solving the problem with ping in games specifically WOT for Wi-Fi from freealbert
WPS on a router - what it is and how to use it
Setting up a connection to a working VPN server using a "gray IP" at the provider from YEDkii
Forced assignment of speed on the port of the router through the CLI from enpa
Resetting factory settings (factory-reset) via CLI from enpa
2 ways to change the MAC address of a computer network card
We fix the display of interfaces in the Connections section of enpa
Firmware update using enpa CLI TELNET command line
Turning off the LEDs of the router using the CLA TELNET command line from enpa
Disabling the FN button LED using the enpa CLI TELNET command line
Solving display problems \ login by domain name (hostname) of Keenetic router in Windows 10 from enpa
Changing a Wi-Fi wireless channel in Keenetic using the enpa CLI TELNET command line
Comments on the work of the Padavana TX Burst
Turn on seamless Wi-Fi roaming and block Internet advertising on Keenetic routers from hwp.ru
TTL lock
Keenetic Recovery
Instructions

Internet connection setup:

Install and configure KeeneticOS:

Reset:

Diagnostics:

Recovery firmware:

Reservation

Speed ​​Limit:

Remote access:

VLAN:

Forwarding and port configuration:

Wi-Fi setup:

WPS (Wi-Fi Protected Setup):

Security and DNS:

schedule :

Tunnels: PPTP, L2TP \ IPSec, IPSec, SSTP, OpenVPN, VPN server:

Digital television:

CLI (command line), SSH:

Modes:

Digital telephony:

IntelliQoS:
Internet speed testing
http://www.speedtest.net/ru/
https://www.nperf.com/ru/
https://2ip.ru/speed/

Attention! Testing servers are provided by external providers and the results of such tests depend on many technical factors.

Test results from these services can only be used for diagnostic purposes.
Application to manage the router
Firmware


The official version of KeeneticOS
Debug version of KeeneticOS
Debug - test (draft) release of the operating system. Repeats the functionality that is in the officially released versions of "Release" or "Beta", but also contains additional fixes and new features. The debug version is under development and may contain bugs.

  • Testing debug versions of KeeneticOS is carried out on the forum Keenetic -here.
  • Changelog of debug versions of KeeneticOS -here.
  • Binary files of debug versions of KeeneticOS, you can download in Keenetic firmware storage -hereandhere.
The program for recovering firmware Keenetic Start II.
KeeneticOS firmware catalog

The curator of the topic is enpa


Post has been editedenpa - 03.07.19, 20:31
Reason for editing: Stable version KeeneticOS 2.15.C.5.0-0 from 06/06/2019 for Start II



Rep: (1038)
Stable firmware version2.11.C.1.0-3 dated 04.04.2018for Start II


Component kit
easyconfig
base
corewireless
ppp
config-ap
pppoe
ydns
config-client
config-repeater
pptp
ppe
skydns
l2tp
dhcpd
dot1x
igmp
miniupnpd
kabinet
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.11.C.1.3

Available for: Keenetic Giga III, Keenetic Ultra II, Keenetic Extra II, Keenetic Giga (KN-1010), Keenetic Omni (KN-1410), Keenetic Extra (KN-1710), Keenetic Ultra (KN-1810), Keenetic 4G III rev.B, Keenetic 4G (KN-1210), Keenetic Start II, Keenetic Lite III rev.B, Keenetic Start (KN-1110), Keenetic Air, Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:

• Fixed a problem with access to local resources for domain names of the 4th level through the service KeenDNS
• Removed the "Debug version" banner in the beta version of the web interface

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.11.C.1.0-3
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.11.C.1.0-3 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.11.C.1.0-3.zip(5.71 MB)

Mirror:
cloud.mail - v2.04-v2.11 Firmware Keenetic
yandex.disk - v2.04-v2.11 Firmware Keenetic
Picture



Rep: (1038)
Firmware 2.12 for ZyXEL Keenetic Start II router

Attached Image

Before installing the firmware, be sure to dobackup firmware and startup-config - here1, here2

After updating the router to 2.12, it is recommended to do Reset to factory settings , configure the router from scratch.

* Experimental firmware (draft \ Debug version)

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
angular-ndw
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.12.A.1.0-1:

Experimental version, in branch 2.11, active work has been suspended due to the release of the official beta, see change log 2.11.

Support for Keenetic III, DSL, VOX and LTE is disabled.
Firmware for new models of Start (KN-1110), 4G (KN-1210) and subsequent KN come out only on the new web interface.

  • IPv6: added the ability to set rules for accessing home hosts via TCP / UDP:
  • ipv6 static (tcp | udp) [interface] {mac} {port} [through {end-port}] - the IPv6 host address is automatically determined by the MAC address, and the port range can be set via port and end-port
  • AdGuard DNS filter added (suggested by @hooddy)
  • fixed conntrack reset when access was denied (reported by @yaparadox)
  • Added output of IPv6 Link-local addresses (at the request of @ r13)
  • IPsec: added support for ECP DH groups for IKE: 19/20/21/22/23 (ECP 192 ... ECP 521)
  • Wi-Fi: Band Steering defaults to passive mode - without sending a forced DEAUTH client
  • Wi-Fi: Fixed desynchronization of the Band Steering tables after the timeout expired, which led to the client being locked
  • Wi-Fi: Fixed shutting down client isolation when adding an additional access point to a segment
  • Wi-Fi: fixed the passage of multicast and broadcast packets between clients of one access point when isolation is turned on
  • Wi-Fi: fixed a possible reason for blocking BBP with the termination of the distribution of beacons for 10-15 seconds
  • Web (beta): added CIFS and AFP setting
  • Web (beta): added support for access point, adapter and repeater modes
  • Web (beta): added segment management in access point mode

Version 2.12.A.1.0-2 dated 1/20/2018:

  • Fixed deadlock in hw_nat when deleting PPP interface
  • fixed bug with broken flow control on WAN MDI and SFP ports KN-1010
  • Improved the performance of the ISP Giga III interface when the flow-control is disabled by the provider
  • Fixed the operation of the E3272s-210 HiLink modem in RNDIS mode
  • Http:fixed double login / password request (reported by @ vk11)
  • Http:SSL certificate is enabled for the automatic domain name {token-alias} .keenetic.io
  • Http:host spoofing is enabled in the Host header on the ip http proxy upstream
  • CIFS: Keenetic NetBIOS detection fixed, for example, using NetBScanner
  • CIFS: Fixed work with WD TV Live
  • SIP: added SIP ALG port setting:
  • ip sip alg port {port}
  • Web (beta): English added
  • Web (beta): fixed scrolling on high resolution screens
  • Web (beta): added current status next to IPoE, PPP sections
  • Web (beta): Added a list of 3G profiles in UsbModem connection settings
  • Web (beta): fixed the error "not found: nat" (reported by @AndreBA)
  • Web (beta): fixed wired connections (reported by @Kiborg_Man)
  • Web (beta): Corrected password entry in the admin panel with iOS (reported @artsel)
  • Web (beta): Fixed shutdown of Wireless ISP (reported by @Sfut)
  • Web (beta): fixed password validation in the DDNS custom profile (reported @ r13)


Version 2.12.A.1.0-3 * dated 1/20/2018:

  • Corrected the output of the Giga III MAC table and related failures in the Web interface (reported by @ iggo)

* laid out in draft only for Keenetic Giga III

Version 2.12.A.1.0-4 dated 01.22.2018:

  • Fixed the error "killing all processes in group" when restarting (reported by @AndreBA) and starting opkg processes (reported by @dexter)

Version 2.12.A.2.0-0 dated 1/25/2018:

  • Netflow: fixed launch of flow-export on hotplug interfaces (reported by @feoser)
  • Http:removed Host and Authorization headers from ip http proxy requests
  • Http:Fixed the error "invalid IP address: 0.0.0.0" in access point mode (reported by @ Leksey118)
  • Http:removed warnings about non-existent files (reported by @ Leksey118)
  • CIFS: fixed calculation of the volume of network drives with long names
  • CIFS: Fixed flags in NetBIOS Registration Requests
  • Web (beta): optimized load time of the main page

Version 2.12.A.2.0-1 dated 1/27/2018:

  • Wi-Fi: fixed WPS button operation with Band Steering
  • Wi-Fi: fixed possible error in the log: Network :: Interface :: Rtx :: Switch: "GigabitEthernet0": system failed
  • Http:Restored Host header transfer to ip http proxy upstream (reported by @Lordmaster)
  • CIFS: fixed Unix-permissions to directories (bit --x-, reported @KorDen)
  • Web (beta): Fixed empty tab "Applications" (reported @ Ari100krat)
  • Web (beta): bug fixed: duplicate key "dyndns" (reported by @ r13)

Version 2.12.A.3.0-0 dated 02.02.2018:

  • SSTP server component added:
  • sstp-server command group - configured in the same way as vpn-server
  • requires SSL-certificate and open access on port 443 for operation
  • accepts connections in direct and cloud mode KeenDNS
  • Added SSTP client:
  • SSTP network interface configured in the same way as PPTP
  • Added the ability to configure routes passed through DHCP INFORM to PPTP clients, L2TP / IPsec and SSTP:
  • vpn-server dhcp route {destination}
  • crypto map l2tp-server dhcp {destination}
  • sstp-server dhcp route {destination}
  • fixed PPTP GRE processing with ppe software enabled
  • replaced the kernel network stack discipline from pfifo_fast to fq_codel (with BQL), providing minimal latency under load
  • increased traffic management priority for PPTP / L2TP VPN
  • corrected session breaks in the DHCP client "rebind" handler
  • joint operation of udpxy and IGMP proxy was restored (reported by @SigmaPlus)
  • Fixed bug of getting extended attributes in tntfs driver (reported by @artsel)
  • Http:Fixed deletion of Authorization header (reported by @ Cha-Cha)
  • UPnP: fixed error delete_redirect_and_filter_rules (reported by @Serge)
  • Transmission: added ability to get Magnet links
  • Web (beta): fixed switch behavior in firewall (reported by @ShadoW)
  • Web (beta): fixed update download on the System page (reported by @ vk11)
  • Web (beta): Fixed blank page Internet filters (reported by @Kiborg_Man)
  • Web (beta): Fixed displaying settings on the KeenDNS page (reported by @ Cha-Cha)
  • Web (beta): added directory access control
  • Web (beta): added support for 6in4 connections

Version 2.12.A.3.0-1 of February 3, 2018:

  • SSTP: Fixed routing DHCP INFORM (reported @ r13)
  • Transmission: added ability to get Magnet links
  • Web (beta): fixed opening of blocks on the main page after navigation (reported by @KorDen)
  • Web (beta): fixed application page in access point mode (reported by @ Leksey118)

Version 2.12.A.3.0-2 of February 06, 2018:

  • fixed L2TP / IPsec client connection
  • Fixed getting routes via DHCP INFORM (reported @ r13)
  • Http:fixed the error "new Web server configuration is invalid" (reported by @ Leksey118)
  • Web (beta): fixed page segments in access point mode

Version 2.12.A.3.0-3 dated 02.10.2018:

  • fixed 100% CPU load with local name resolution error via ndnproxy
  • IPsec: added a command to disable rekey on L2TP / IPsec, EoIP / IPsec, Gre / IPsec, IPIP / IPsec tunnels: interface {name} ipsec nail-up
  • Wi-Fi: added display of open networks in site-survey (KN-1010)

Version 2.12.A.3.0-4 dated 02.15.2018:

  • ping-check redesigned from netfilter rules to RPDB + multiple routing table
  • Added timeout for internal NeighbourListener stream operations (reported by @OmegaTron)
  • Wi-Fi: fixed possible deadlock system, subject to Keenetic Giga III, Ultra II, Air, Extra
  • Wi-Fi: fixed bug with 2-way / 4-way handshake (GTK / PTK), all mt7628 models are affected
  • Wi-Fi: added Reason logging for DEAUTH and DEASSOC events
  • DHCP: fixed "gateway is unreachable" error when the client received an address with a mask / 32
  • DNS: Enabled use of provider's servers for non-filtered Yandex.DNS, Norton and AdGuard hosts
  • IPsec: added support for ECP DH groups for Phase 2 SA: 19/20/21/22/23 (ECP 192 ... ECP 521)
  • Transmission: By default, encrypted connection preference is reduced, reducing download speed (reported @alexmay)
  • UPnP: added auto-delete rules for disabled hosts
  • Web (beta): fixed bugs in KeenDNS page

Version 2.12.A.4.0-0 dated 02.17.2018:

  • The SSH server component has been added: service ssh — starting the service; ip ssh port {port} - change the port, the default is 22; ip ssh security-level (public | private | protected) —access policy, default private; ip ssh lockout-policy {threshold} [{duration} [{observation-window}]] - block brute force blocking; threshold - the number of attempts to iterate, from 4 to 20, the default is 5
  • duration - blocking time, from 1 to 60 minutes, by default 15; observation-window - window from 1 to 10 minutes, by default 3; ip ssh keygen (default | ...) - regeneration of a key of the specified type; show ssh fingerprint - show fingerprints of current keys
  • Opkg: added support for ISO 9660 and UDF file systems in opkg-kmod-fs (reported by @ Ildar)
  • Web (beta): Fixed list of wired connections (reported by @Lordmaster)
  • Web (beta): added support for Keenetic Plus DECT
  • Web (beta): updated file browser component

Version 2.12.A.4.0-1 dated 02.19.2018:

  • fixed system failed [0xcffd02e1] in access point mode (reported by @AndreBA)
  • Wi-Fi: fixed reboot with double deletion of STA record, prone to Giga (KN-1010)
  • Opkg: added support for DVB tuner TBS5520SE

Version 2.12.A.4.0-2 dated 02.22.2018:

  • restored compatibility with NordVPN *
  • Added support for ARP Proxy on L2TP / IPsec and SSTP server (reported by @Dmitry Tumashev)
  • fixed change of priorities of connections at boot (reported @ r13)
  • SSH: Fixed deletion of obsolete SSH key prints (reported @ r13)
  • SSH: removed "Invalid password for user admin" messages when logging in under a different login (reported by @yjus)
  • SSH: fixed "User has invalid shell" bug (reported by @KorDen)
  • IPsec: improved connection stability, fixed removal of CHILD_SA
  • OpenVPN: fixed installation routes (reported by @Lordmaster)
  • Web (beta): fixed "no entry for IP" errors when working through the cloud (reported @ Leksey118)
  • Opkg: Fixed crash of DVB-tuner driver TBS5520SE (reported by @KorDen)


* ISP blocking was caused by NetBIOS operation in the VPN channel
Version 2.12.A.4.0-5 of 03/03/2018:

  • added QDMA support in hw_nat mt7621, eliminated the problem of IPTV drops with heavy WAN в†’ LAN load traffic
  • redone brute force detection from netfilter to ipset
  • added lockout-policy support for FTP
  • added lockout-policy support for form-based HTTP authorization
  • Fixed the ping utility (reported by @ Equalizer)
  • Wi-Fi: added 80M_CAP flags on channels 132..140 and 40M_CAP on channels 1..4 while auto select (KN-1010)
  • Transmission: increased maximum download speed to 12 Mb / s on Giga (KN-1010) *
  • Transmission: added linear loading option (as requested by @plagioklaz):
  • CIFS: fixed buffer overflow and process restart when writing in large blocks
  • Opkg: Added support for Tuner Technisat SkyStar USB HD DVB-S2
  • Web (beta): Corrected the order of USB ports on the Giga (KN-1010) (reported @ Ari100krat)
  • Web (beta): Fixed Chrome authorization on iOS (reported @ r13)
  • Web (beta): fixed button layout in cloud service settings (reported by @AndreBA)
  • Web (beta): MU-MIMO removed from Giga III settings (reported by @ iggo)
  • Web (beta): added Keenetic Plus DECT lines and calls to dashboard
  • Web (beta): Keenetic Plus DECT call history added
  • Web (beta): IntelliQoS page added

* for maximum results, it is recommended to disable uTP
Version 2.12.A.4.0-6 of 03/07/2018:

  • Fixed regression of data transfer to Giga III port 5 (MAC-PHY I / O driving strength)
  • fixed TTL decrement in fast_nat module when transferring LAN в†’ WAN packets
  • repaired traffic counters of registered hosts on protected segments
  • IPsec: added support for enforcing ESP to UDP encapsulation for client tunnels:
  • interface {name} ipsec force-encaps
  • CIFS: memory usage optimized
  • Opkg: Fixed bugs with the Technisat SkyStar USB HD DVB-S2 adapter (reported by @vlasky)
  • SSH: dropbear updated to 2018.76 with support for local TCP forward and SOCKS proxy
  • uClibc-ng updated to 1.0.29

Version 2.12.A.4.0-9 of 03/23/2018:

  • fixed link detection on some versions of E3372 HiLink (reported by @DVA_War)
  • Fixed proxying of the Web-interface of modems and Huawei routers via KeenDNS (reported by @Andrew Voronkov)
  • fixed system reboot when background commands work (reported by @ Kinetic Guide)
  • Linux kernel: migrated various long-term updates to the network stack and USB
  • Wi-Fi: it is forbidden to switch to 2.4 GHz CCK modulation in N and GN modes, all models are affected
  • Wi-Fi: fixed reboot when receiving an invalid RMAC INFO descriptor, all mt7628 models are affected
  • Wi-Fi: fixed reboot when turning off the TD button during autoscan, all mt7628 models are affected
  • Wi-Fi: Fixed BBP reset logic over MDRDY counter, subject to Keenetic Air, Extra II and subsequent dual-band models
  • Wi-Fi: added decoding of the Reason code of DEASSOC and DEAUTH events
  • DNS: fixed switching between SkyDNS and Yandex.DNS (reported by @BACbKA)
  • IPv6: fixed tracking of host states in the home network (reported by @vleonv)
  • OpenVPN: added support for iroute in server mode (reported by @Pablo)
  • DLNA: added the ability to change the server name (at the request of @ vk11): dlna display-name {display-name}
  • AFP: RAM usage optimized
  • AFP: DHXv1 authorization disabled
  • FTP:Added the ability to set the default root directory: ip ftp root {directory}
  • FTP:fixed work in passive mode when changing the main server port
  • DECT: added ability to change the polling interval of the tubes:
  • dect base handset-poll-timer {timer}, default is 60000 (1 minute)
  • Web (beta): re-corrected the order of USB ports on the General Settings page (reported @ Ari100krat)
  • Web (beta): Fixed saving DNS settings in local segments (reported @hooddy)
  • Web (beta): Fixed saving settings for CIFS and AFP (reported by @Kiborg_Man)
  • Opkg: added support for Technisat SkyStar USB 2 HD CI adapter
  • Added debug information when "unexpectedly stopped" errors

Version 2.12.A.4.0-11 of 03/23/2018:

  • restored for Omni II, no different from 2.12.A.4.0-9

Version 2.12.A.5.0-1 of 04/06/2018:

  • Added rules for choosing the default route for hosts and home network segments (Multiple WAN routing policy) *:
  • ip policy {name} - create a routing policy
  • ip policy description {description}
  • ip policy permit global {interface} [order {order}] - allow connection with the specified priority
  • ip policy permit auto - allow new connections automatically (disabled by default)
  • ip hotspot default-policy (permit | deny | {policy}) - set the default policy
  • ip hotspot policy {interface} (permit | deny | {policy}) —set policy for unregistered hosts in the home network segment
  • ip hotspot host {mac} policy {policy} - set a policy for a registered host
  • Internet access control for registered hosts is divided into three commands:
  • ip hotspot host {mac} permit - allow access
  • ip hotspot host {mac} deny - deny access
  • ip hotspot host {mac} schedule {schedule} - enable access on a schedule, can be configured simultaneously with the policy
  • changed the format of the name of the firmware file when downloading from the device: {device} _ {sandbox} _ {version} .bin
  • added a command to disable polling of the CDC modem link byHttp:interface usb wwan-force-connected
  • bug fixed Core :: Scgi :: ThreadPool: not found: "hotspot" in access point mode (reported @ Leksey118)
  • IPv6: Improved algorithm for tracking the status of hosts in the home network
  • IGMP: fixed group subscription timeout when General Query was lost
  • IGMP: DSCP and qdisc packets are raised to reduce loss of query under load
  • DNS: Fixed processing of requests on public interfaces with the SkyDNS, Yandex.DNS filter turned on, and related service failures
  • CIFS: Fixed SMB_STATUS_END_OF_FILE error when moving beyond the file (reported @ TDR2000 MK2)
  • DHCP: receiving multicast routes from the provider is disabled
  • SNMP: interface overflow bug fixed
  • DECT: added support for parallel calls on one handset: dect parallel disable - disable the function of parallel calls
  • DECT: added combinations of buttons to control parallel calls:
  • dect parallel toggle - switch between active and held call
  • dect parallel hold-resume - hold / resume the current call (the call that is on hold, calls back if you hang up)
  • dect parallel release-active - end an active call
  • dect parallel release-passive - hold call termination
  • dect parallel accept - receive a parallel incoming call
  • dect parallel reject - hang up a parallel incoming call
  • dect parallel transfer - transfer an active call
  • dect parallel intercept - intercept a call from an adjacent handset
  • dect parallel call-internal - making a parallel call to the adjacent handset (by the handset ID)
  • dect parallel call-external - making a parallel call to an external number
  • DECT: added commands to prohibit the reception and interception of a call on the line: dect sip deny-pickup - prohibit reception; dect sip deny-interception - disable interception
  • DECT: phonebook support added: dect phonebook length - maximum number of entries in the phonebook; dect phonebook handset-edit - enable phonebook editing from the handset; dect phonebook last-name-first — display first the last name, then the first name; dect phonebook match-length - the number of the last digits of the incoming number to search the phone book
  • DECT: added polling handset status (enabled / disabled)
  • DECT: Added display of the caller's name on Gigaset handsets.
  • DECT: added support for Semi-attended call transfer (RFC 5589, clause 7.6)
  • DECT: fixed module reset when Caller ID is sent to Panasonic GAP handsets
  • Web (beta): the Connection Priorities page has been added to easily configure ip policy: changing priorities and linking to a profile is done by dragging and dropping:
  • Web (beta): IGMP proxy configuration fixed (reported by @m__a__l)
  • Web (beta): fixed icons on the "General Settings" page (reported by @VirtuoozX)
  • Web (beta): fixed loss of communication with the device (reported by @ iggo)
  • Web (beta) fixed firmware file type (reported @ r13)
  • Megafon MR300-1 USB modem support added (Huawei E5786s-32a)
  • OpenSSL updated to 1.1.0h

* IPv6 not supported yet
Version 2.12.A.5.0-2 dated 04.04.2018:

  • fixed Routing Policy for connections with static IP settings
  • Http:fixed SSL service blocking
  • Web (beta): parallel call settings added
  • restored Keenetic Omni assembly

(c)https://forum.keenetic.net/

Attached fileKeenetic Start II_2.12.A.5.0-2.zip(6.26 MB)

Mirror:
cloud.mail: v2.04 - 2.12 (Test, Beta Firmware) All Keenetic
yandex.disk: v2.04 - 2.12 (Test, Beta Firmware) All Keenetic

If there are problems with the firmware

Instructions

Picture



Rep: (2)
Share the SPI flash U14 25Q128CS1G dump.
And then the device stopped distributing the Internet, the web worked for half, started using telnet, flipped through the list of commands, but did not do the reboot;
Thank.



Rep: (0)
Where can I get it?



Rep: (1038)
Official beta firmware version2.12.B.0.0-0 dated 05.23.2018for Start II

<Starting with firmware version 2.12, the old web interface has been removed. >

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

New WebUI Screenshots
Attached Image

Attached Image

Attached Image

Attached Image

Attached Image

Attached Image

Attached Image

Attached Image

Changes
Version 2.12.B.0.0-0 (official beta *):

Available for: Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:

• Changed web interface design
• Added the ability to select the default route for hosts and home network segments (Policy Based Routing)
• SSTP server and client added
• Added SSH server
• AdGuard DNS filter added.
• Added support for ARP Proxy on L2TP / IPsec and SSTP server
• Improved Wi-Fi performance
• SIP: SIP ALG port setting added
• IPsec: improved connection stability
• IPv6: added ability to set home host access rules over TCP / UDP
(with)http://service.ndmsystems.com/changelog.html

Installation process and debug mode
1. Download firmware version 2.12.B.0.0-0
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.12.B.0.0-0 there are problems, you will need to do the following:

1. Disable disable all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all the devices from the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.12.B.0.0-0.zip(5.74 MB)

Mirror:
cloud.mail - v2.04-v2.12 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.12 (Test, Beta Firmware) All Keenetic
Picture



Rep: (1038)
Official beta firmware version2.12.B.0.0-2 of 05/31/2018for Start II

<Starting with firmware version 2.12, the old web interface has been removed. >

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.12.B.0.0-2 (official beta *):

Available for: Keenetic 4G III rev.B., Keenetic 4G (KN-1210), Keenetic Air II, Keenetic Start II, Keenetic Lite III rev.B, Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:
• A number of fixes and improvements in the user interface on the pages "Users"
• Also reduced the load on the processor of the Internet center, created by the work of the web interface
• Fixed co-operation of the PingChecker service with OpenVPN
• Fixed access to web applications on the home network via KeenDNS in SSL mode
(with)http://service.ndmsystems.com/changelog.html

Installation process and debug mode
1. Download firmware version 2.12.B.0.0-2
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.12.B.0.0-2 there are problems, you will need to do the following:

1. Disable disable all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all the devices from the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.12.B.0.0-2.zip(5.74 MB)

Mirror:
cloud.mail - v2.04-v2.12 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.12 (Test, Beta Firmware) All Keenetic
Picture



Rep: (1038)
Stable firmware version2.12.C.0.0-1 from 07/09/2018for Start II


Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.12.C.0

Available for: Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:

• Changed web interface design
• Added the ability to select the default route for hosts and home network segments (Policy Based Routing)
• SSTP server and client added
• Added SSH server
• AdGuard DNS filter added.
• Added support for ARP Proxy on L2TP / IPsec and SSTP server
• Improved Wi-Fi performance
• Implemented SSID support in UTF-8
• Added SIP ALG port setting
• Improved IPsec connection stability
• IPv6: added ability to set home host access rules over TCP / UDP
• Implemented IGMP snooping in additional modes
• Fixed access to web applications on the home network via KeenDNS in SSL mode

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.12.C.0.0-1
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.12.C.0.0-1 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.12.C.0.0-1.zip(6.02 MB)

Mirror:
cloud.mail - v2.04-v2.12 Firmware Keenetic
yandex.disk - v2.04-v2.12 Firmware Keenetic
Picture



Rep: (0)
Good day! I got this device in the store for distributing waffles ... and, unexpectedly, he puts IP-phones, at what, concrete, Escene. What is the reason, I can not understand. Please tell me thanks in advance!



Rep: (1038)
Stable firmware version2.12.C.1.0-3 dated 08.08.2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.12.C.1

Available for: Keenetic 4G III rev.B., Keenetic 4G (KN-1210), Keenetic Air II, Keenetic Start II, Keenetic Lite III rev.B, Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:
• Added work schedule selection for VPN tunnels and modems
• Fixed error updating the KeenDNS IP address in direct access mode for PPP connections
• Fixed problem with reconnection OpenVPN
• Fixed possible authentication error through the web interface.
• Fixed loading page "Other connections"
• Fixed registration of home network devices by MAC address
• Fixed the layout of the "Wi-Fi Clients" page in the "Access Point" and "Amplifier" modes
• Fixed display of mobile application clients
• Fixed the size of the log window on a mobile device

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.12.C.1.0-3
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.12.C.1.0-3 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.12.C.1.0-3.zip(6.03 MB)

Mirror:
cloud.mail - v2.04-v2.12 Firmware Keenetic
yandex.disk - v2.04-v2.12 Firmware Keenetic


Official beta firmware version2.13.B.0.0-0 of 08/30/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.13.B.0.0-0

Available for: Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:
• Implemented access to the device via backup connections
• Fixed TTL fix on outgoing packets
• Web: changed the menu design on the main page
• Web: added option for additional Multicast VLAN and additional PVC for IPTV
• Web: improved adaptive layout for small screens
• Web: fixed bugs
• Wi-Fi: implemented MAC-Repeater mode without translating MAC addresses
• Wi-Fi: support for MAC ACL access lists on segments
• Wi-Fi: support for 802.11k / r in manual configuration mode
• Wi-Fi: support for SSID encoded in UTF-8
• IPv6: Yandex.DNS support implemented
• SSTP: Anonymous-DH mode added for compatibility with non-certificate SSTP servers
• L2TP / IPsec server: fixed adding routes through remote clients
• L2TP / IPsec client: shortened the minimum PSK length to three

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.13.B.0.0-0
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.13.B.0.0-0 you have problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.13.B.0.0-0.zip(6.02 MB)

Mirror:
cloud.mail - v2.04-v2.13 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.13 (Test, Beta Firmware) All Keenetic
Picture



Rep: (1038)
Official beta firmware version2.13.B.0.0-2 of 09/07/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
Version 2.13.B.0.0-2

Available for: Keenetic Giga III, Keenetic Ultra II, Keenetic Extra II, Keenetic Extra (KN-1710), Keenetic Omni (KN-1410), Keenetic 4G III rev.B, Keenetic 4G (KN-1210), Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:
• Fixed setting CaptivePortal
• Web: fixed deletion of segment settings
• Web: improved layout

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.13.B.0.0-2
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If you have problems after installing 2.13.B.0.0-2, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.13.B.0.0-2.zip(6.02 MB)

Mirror:
cloud.mail - v2.04-v2.13 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.13 (Test, Beta Firmware) All Keenetic
Picture


Post has been editedenpa - 11.09.18, 17:13



Rep: (6)
Today, after turning off the lights in the house, the router stopped seeing the Internet cable of the provider. I think the van port has burned out. I tried to connect the cord directly from the computer to the port van. I also tried from the LAN port of the router itself to plug the wire into the VAN by the rabbi. does not work. The indicator - the globe does not light up (or rather, it only lights up briefly when the router is turned on). What to do? How to be?



Rep: (1038)
Stable firmware version2.13.C.0.0-1 dated 10/02/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.13.C.0.0-1

Available for: Keenetic Giga III, Keenetic Ultra II, Keenetic Extra II, Keenetic Giga (KN-1010), Keenetic Extra (KN-1710), Keenetic Ultra (KN-1810), Keenetic Omni (KN-1410), Keenetic 4G III rev.B., Keenetic 4G (KN-1210), Keenetic Air II, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:

• Fixed USB-modem MF710M TELE2
• Fixed VLAN support in additional modes.
• Wi-Fi: improved WPS security
• CIFS: fixed access to network storage when using access rights

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.13.C.0.0-1
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.13.C.0.0-1 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.13.C.0.0-1.zip(5.97 MB)

Mirror:
cloud.mail - v2.04-v2.13 Firmware Keenetic
yandex.disk - v2.04-v2.13 Firmware Keenetic
Picture



Rep: (1)
Original dump from Start 2
There is also an openwrt dump from the Xiaomi mi3c theme from movgai ... It works even without replacing EEProm .. but it’s better to take it from your router .. For an openwrt description, see also Xiaomi mi 3c topic

Attached files

Attached fileStart2.zip(18.05 MB)



Rep: (100)
* nLLIeHu4ka how to dump openwrt sew? Through the web interface?
Another confusing size, 16MB dump, when we have a memory of 8MB. So easy to sew?
and how to eeprom?

Post has been editedcommandos98 - 31.10.18, 01:28



Rep: (1038)
Stable firmware version2.13.C.0.0-3 dated 10/17/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.13.C.0.0-3

Available for: Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:
• Fixed the reasons for the possible instability of the software network accelerator
• IPsec: restored compatibility with CyberGhost service

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.13.C.0.0-3
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.13.C.0.0-3 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.13.C.0.0-3.zip(5.97 MB)

Mirror:
cloud.mail - v2.04-v2.13 Firmware Keenetic
yandex.disk - v2.04-v2.13 Firmware Keenetic
Picture


Post has been editedenpa - 31.10.18, 11:16



Rep: (1)
A dump only through the programmer .. spi in the router costs 16 mb ... you can see only 8 on the stock ...



Rep: (1038)
Official beta firmware version2.14.B.0.0-1 dated 11/08/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
nortondns
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.14.B.0.0-1

Available for: Keenetic Air, Keenetic Start II, Keenetic Lite III rev.B., Keenetic Start (KN-1110), Keenetic Lite (KN-1310), Keenetic City (KN-1510), Keenetic Air (KN-1610),

New features and other improvements:

• Added the ability to simultaneously use WAN connections in balance mode
• Web interface: added Host Traffic Monitor
• Web-interface: added the function of printing a QR-code to connect to a Wi-Fi network
• Web-interface: fixed bugs
• KeenDNS: Added option "cloud access over IPv6" (does not require IPv6 on the device)
• VPN: increased number of tunnels
• Kabinet: added ability to set the server port

(c)http://service.ndmsystems.com/

Installation process and debug mode
1. Download firmware version 2.14.B.0.0-1
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.14.B.0.0-1 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disablesdebug mode.
6. We send debug self-test fileofficial technical support.

Attached fileKeenetic Start II_2.14.B.0.0-1.zip(6.22 MB)

Mirror:
cloud.mail - v2.04-v2.14 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.14 (Test, Beta Firmware) All Keenetic
Picture



Rep: (1038)
Stable firmware version2.14.C.0.0-0 from 12/03/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.14.C.0.0-0

New features and other improvements:

• Added support for USB modems Alcatel IK40V; Huawei E5776; TELE2 ZTE MF920V MiFi
• Added the ability to simultaneously use WAN connections in balance mode
• KeenDNS: Added option "cloud access over IPv6" (does not require IPv6 on the device)
• Wi-Fi: added setting of the region option "Kazakhstan" for 5 GHz
• Wi-Fi: improvements in roaming
• Web interface: added Host Traffic Monitor
• Web-interface: integrated context help
• Web-interface: added the function of printing a QR-code to connect to a Wi-Fi network
• Web-interface: fixed bugs
• Transmission torrent client: updated to version 2.94
• Updated OpenSSL library
• VPN: increased number of tunnels
• Kabinet: added ability to set the server port

New features of Keenetic Plus DECT:

• Added auto dial function
• Added setting for early voice call encryption
• Added support for Panasonic KX-TGA806, Panasonic KX-TGA810, Panasonic KX-TGA550, Yealink W52P handsets
• Fixed the problem of replacing the outgoing call number when selecting a line through #
• Fixed export of calls to CSV

(c)https://help.keenetic.com/

Installation process and debug mode
1. Download firmware version 2.14.C.0.0-0
2. Installby file upload.
3. Be sure to dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.14.C.0.0-0 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disableshttps://help.keenetic.com/.
6. We send debug self-test fileofficial technical support.

Attached filekl_rg_stable_2.14.C.0.0-0.zip(5.97 MB)

Mirror:
cloud.mail - v2.04-v2.14 Firmware Keenetic
yandex.disk - v2.04-v2.14 Firmware Keenetic
Picture



Rep: (1038)
Stable firmware version2.14.C.0.0-4 from 12/26/2018for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.14.C.0.0-4

Corrections:

Fixed renewal of SSL certificates

(c)https://help.keenetic.com/

Installation process and debug mode
1. Download firmware version 2.14.C.0.0-4
2. Installby file upload.
3. Dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.

If after installing 2.14.C.0.0-4 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.

Attached filekl_rg_stable_2.14.C.0.0-4.zip(5.97 MB)

Mirror:
cloud.mail - v2.04-v2.14 Firmware Keenetic
yandex.disk - v2.04-v2.14 Firmware Keenetic
Picture



Rep: (1038)
Official beta firmware version2.15.B.0.0-1 of February 11, 2019for Start II

Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components

Changes
2.15.B.0.0-1

Supported Models:

Keenetic Giga (KN-1010)
Keenetic Start (KN-1110)
Keenetic 4G (KN-1210)
Keenetic Lite (KN-1310)
Keenetic Omni (KN-1410)
Keenetic City (KN-1510)
Keenetic Air (KN-1610)
Keenetic Extra (KN-1710)
Keenetic Ultra (KN-1810)
Keenetic Viva (KN-1910)
Keenetic DSL (KN-2010)
Keenetic Duo (KN-2110)
Zyxel Keenetic Start II
Zyxel Keenetic Lite III rev.B
Zyxel Keenetic 4G III rev.B
Zyxel Keenetic Giga III
Zyxel Keenetic Ultra II
Zyxel Keenetic Air
Zyxel Keenetic Extra II

Beta version is the official release of updated components that have undergone internal testing and are at the stage of final debugging.

To install the beta version, we recommend updating the Internet Center from mobile devices via the My.Keenetic application or the web configurator.

New features and improvements:

The component "Wi-Fi system controller" has been added to automatically control access points connected via cable;
Implemented support for 802.11v WNM BTM (BSS Transition Management);
Fixed PMK-R1 key exchange problems in FT roaming;
Implemented traffic monitor for arbitrary registered devices;
Implemented ACMEv2 protocol and getting wildcard certificates for KeenDNS domain names;
A form for accepting an End-user License Agreement has been added to the Quick Setup Wizard;
Added support for new Keenetic mobile app;
The automatic connection mode ADSL / VDSL (models KN-2010, KN-2110) is implemented;
Added support for USB modems MTS 872FT, MTS 874FT, MTS 835FT (MF920T) (for models with USB port);
Additional modes: port 0 has been added to the segment settings (for Keenetic Giga III, Ultra II, Giga, Ultra and Viva);
Fixed 802.1p packet transmission with zero VLAN ID;
The implementation of the SMB / CIFS server has been changed from CIFS NQ to Tuxera SMB (for models with USB storage support):
- Support for durable filehandles (launch applications from a network drive, etc.);
- Support master browser function;
- Support for Windows Backup;
- Support for Apple Time Machine.

New features Zyxel Keenetic Plus DECT:

Added support for Panasonic KX-TG7175, Panasonic KX-TG8562, Panasonic KX-PRXA10;
The correct display of numbers with an extension set on CAT-iq 2 handsets is implemented;
Implemented limiting line selection through # in accordance with the rules of dialing;
Fixed problem when re-copying call history or phone book;
Fixed replacing the outgoing call number when the replacement rule contains T;
Fixed line selection through # when dialing one character at a time.

(c)https://help.keenetic.com/

Installation process and debug mode
1. Download firmware version 2.15.B.0.0-1
2. Installby file upload.
3. Check the work.

If after installing 2.15.B.0.0-1 there are problems, you will need to do the following:

1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.

Attached filekl_rg_beta_2.15.B.0.0-1.zip(6.26 MB)

Mirror:
cloud.mail - v2.04-v2.15 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.15 (Test, Beta Firmware) All Keenetic
Picture


Full version    

Help     rules

Now: 07/17/19, 20:54