Xiaomi Redmi Note 5 Global / Note 5 China - MIUI Firmware
Agat11 @ 27.07.18, 10:27
which version you need to download to install through three points
For TWRP, Full.
milomi, milomi @ 27.07.18, 08:45
redmi note 5 China. it came with firmware 9.5.17.0.0 (OEIMIFA) (flip-flops). Looked loader status in the Developer menu - written "The bootloader is unlocked." Looked through the loader status Fastboot - it says that is blocked. That is the Chinese behind closed crooked loader. In any case, filed his MI ID in the subject on the official forum, firmware download for permission to EDL. Yesterday the respected elvis574184 from your account in the EDL flashed through the last MiFlash on 8.7.12 China Developer with Clean All. This is absolutely not helped. Despite the fact that the firmware has become MIUI10, firmware version remained 9.5.17.0.0. loader status in the system was also "unlock", and in Fastboot "Blocked". After I received permission to firmware in the EDL and I flashed on 8.7.12 Global Developer with Clean All and Lock. But it did not help. Everything remained the same. Prompt how to flash the phone to the drain, so that I could unlock it officially?
first: OEIMIFA - this is not Vietnamese. OIIMIFA - Vietnamese. clarify this point, what is your - this is important for future decisions!
Second, check the version of the ARB. once sewed 07/08/12 and firmware MIUI became 10, then you already 4 ARB.
Third, if you do not know English, then use the Google-translation! this applies to all users, to spread messages or screens the program settings - where she says that you are doing wrong and what your problem is.
Fourth, based on item 3 you need to perform not Clean (cleaning) and Flash (firmware). and it is in the instructions in the header and the Chinese for lifting bricks.
Five: here already repeatedly wrote that when attempting to lock the bootloader on globalke, stitched on a Chinese phone you get butlup! what you are trying to do - open masochism.
Sixth: to ARB 3 solution to your problems described several times in the subject. flash strictlyChinese firmware (if you already ARB4, then sew the firmware only ARB4) with boot lock (flash all lock). make an account and apply for unlocking wait 360 hours. unlock the bootloader and flash globalku but downloader not lock . work-whether this method to ARB 4 - check. worse than your brick-and-so will not, but if it will - share the results in the subject.
P.S. do not try to do everything at once. First raise your brick strictly according to the instructions of the Chinese (globalkoy 8.7.12) and make sure that the phone is alive and loaded into the system. and only then try to sew on the Chinese firmware.
Post has been editedshurkesha - 27.07.18, 12:15
per66 , Here in the cart people are friendly advise to proceed https: //drive.google.c...LIrBGjQL2yQHrWSPKGFpAy  |
Post has been editedwanted167 - 27.07.18, 13:24
elvis574184, Today updated with 08.07.12 on 08.07.26 through TWRP Red Wolf, Download Firmware herehttp://ru.miui.com/download-340.html
Wipes are made, install the firmware, set Magisk v16, overloaded in rekaveri, and then restart the system, normal flight!
FAQ on the main sections in TWRP
General information: - Boot - Boot kernel.
- Recovery - Recover.
- System - System.
- System Image (system.img) - The system image in img format. It is not recommended to backup, And even more to restore,bootlapoften.
- Data - Custom application data, system settings (usually does not include the internal memory).
- Cache - Cash.
- Internal Storage - Inner memory.
- Modem - Modem (Us).
- Cust - Section responsible for the regions.
- EFS - IMEI, MAC-address, SN device ( mostly backups once and for all, until the phone on hands ).
- Persist - Various device sensors, also related to MI Account.
- Bootloader (aboot) - loader.
- Splash - Boot logo.
- Vendor - so let's say the driver
- Vendor image - Vendor look
Forums for Backup and restore system settings and applications:
- Boot, System, Data, Vendor
Post has been editedDima_Apatity - 12.02.19, 14:48
Masik в„ў U 2.1
Updated: July 27, 2018 (16:00)
Greetings, friends: thank_you:
REFERENCE TO POST WITH FIRMWARE
This firmware can be installed on any version of MIUI any status ARB.
Updated the description of the firmware in the corresponding post.
For any question you can always contact me at QMS. Successful use. .
Post has been editedderak1129 - 10.04.19, 19:15
Updated: July 27, 2018 (16:00)
Greetings, friends: thank_you:
REFERENCE TO POST WITH FIRMWARE
This firmware can be installed on any version of MIUI any status ARB.
Updated the description of the firmware in the corresponding post.
For any question you can always contact me at QMS. Successful use. .
Post has been editedderak1129 - 10.04.19, 19:15
zvezdec @ 27.07.18, 22:51
who updated from 8.7.12 to 8.7.26 on the global machine through twrp, unsubscribe - everything was normal. Afraid to get something brick
In general, I updated and raised carts with 3 to 4 without using a computer.
The procedure is as follows:
1. Download the 3 firmware 8.7.5, 8.7.12 and 7.8.26 (I should say, the latter can not shake.)
2. Download rekaveri from mrrot (standing redvulf was not sure that would work on it).
3. Restart in rekaveri, changed it to mrrot. I rebooted into an altered rekaveri.
4. Did wipes are all in addition to the internal memory. Manually delete all the folders except the right (photo, upload).
5. Set of rekaveri 8.7.5 (07/08/12 zaboyalsya immediately, conflicting information in the subject line)
6. Restart in miyuay, configured it.
6.1 Restart rekaveri convinced that it has become a standard. I moved back to miyuay.
7. After 3 point set 07/08/12
8. A staff update looked refreshed found ota 8.7.26 and update it.
Well, something like this.
Apparatus Global 4/64
Post has been editedKUS333 - 27.07.18, 19:55
Go with flip-flops on the official firmware
Retreat
Chinese version of the device firmware with the global, with a locked bootloader. Although visually and it seems that it is enabled: splash, developers in the menu "Loader Status" indicates "unlocked". But when checking fastbut blocked !
Instruction will be in two forms, for each type of loader with ARB3 and ARB4.
Instruction will be in two forms, for each type of loader with ARB3 and ARB4.
ARB3
Required
- Apparatus in EDL mode. How to translate, you can learn here .
- Official Chinese firmware based onARB3 China Stable
- 9.5.21.0
- 9.5.16.0
- 9.5.14.0
- 9.5.12.0
- 9.5.4.0
- 8.7.5 and below
- 9.5.21.0
- MiFlash 2016.08.30.0 -
MiFlashSetup.msi (31.03 MB) - Text editor such as Notepad ++
Small manual
- Unpack the firmwaredrive C (Without the Cyrillic alphabet in the way)
- Set MiFlash (if required, disable the driver signature verification)
- Openrawprogram0.xml and find the block about section persist In such portion therein and append the section namepersist.img (Between quotation marks):filename = ""filename = "persist.img"The whole unit will thus<program SECTOR_SIZE_IN_BYTES = "512" file_sector_offset = "0" filename = "persist.img" label = "persist" num_partition_sectors = "65536" partofsingleimage = "false" physical_partition_number = "0" readbackverify = "false" size_in_KB = "32768.0" sparse = "true" start_byte_hex = "0x10000000" start_sector = "524288" />
- Mode flash deviceedl .
- Now it will be possible to link the loader with your account, in developed and officially unlock menu, after that time, which indicates MiUnlock. :)
ARB4
Required
- Account with permission to re-flash mode in EDL . If not available, then try the so - Xiaomi Redmi Note 5 Global / Note 5 China - MIUI firmware (Post Dima_Apatity # 76921300)
- MiFlash 2018.05.28.0 ( Cloud )
- Drivers
- Chinese Official firmware, it is advisableChina Developer (ARB4) China Stable
- 9.6.3.0
- 9.5.22.0
- 8.7.12 and above
- 9.6.3.0
- Text editor such as Notepad ++
- Ability and desire to disassemble the unit and close the test point. How to do this is described here .
Small manual
- Unpack the firmwaredrive C (Without the Cyrillic alphabet in the way)
- Openrawprogram0.xml and find the block about section persist In such portion therein and append the section namepersist.img (Between quotation marks):filename = ""filename = "persist.img"The whole unit will thus<program SECTOR_SIZE_IN_BYTES = "512" file_sector_offset = "0" filename = "persist.img" label = "persist" num_partition_sectors = "65536" partofsingleimage = "false" physical_partition_number = "0" readbackverify = "false" size_in_KB = "32768.0" sparse = "true" start_byte_hex = "0x10000000" start_sector = "524288" />
- Mode flash deviceedl .
- Now it will be possible to link the loader with your account, in developed and officially unlock menu, after that time, which indicates MiUnlock. :)
Post has been editedDima_Apatity - 12.02.19, 14:48
Restore partition persist
For other ways to restore this section you can read here
Post has been editeddestroyer71 - 15.08.18, 16:14
Restoring using MiFlash
Download the file, unzip to any location on your PC. Open Utility Mi Flash. Press the select button, select the extracted folder. Translate device in edl mode. Press in Mi Flash refresh. The device must be defined as a COM xx (where xx - is the port number). Choose clean all. Press the flash. All section persist overwritten. It is understood that the driver and Mi Flash is already installed on the PC. In any case, I made 2 files. For the version of loader 2 (ARB3) and for the new loader 3 (ARB4)
Restoring_Persist_ARB3.zip(855.9 KB)
Restoring_Persist_ARB4.zip(856.1 KB)
To restore the partition to persist ARB 4 need an authorized account (as of rise for the "bricks"). For version 3 ARB account is not required.
Restoring_Persist_ARB3.zip(855.9 KB)Restoring_Persist_ARB4.zip(856.1 KB)To restore the partition to persist ARB 4 need an authorized account (as of rise for the "bricks"). For version 3 ARB account is not required.
Post has been editeddestroyer71 - 15.08.18, 16:14
Restoring section Persist, restoring MAC-Adresse, recovery of the sensors and cameras, disposal of OIIMIFA, without EDL, without fastbuta with ARB4
We will needcustom recovery with a terminal inside, here e.g. such a .
Need to downloadthe last (Or any other, is the same everywhere Persist) firmware for the drain miflesha unpack it and find a file persist.img After throw it directly into the root of the internal memory ( /sdcard/persist.img ). Now follow the instructions
- Reboot in rekaveri
- When you start rekaveri go to Extras ->Terminal (you may be on another)
- there are writingsimg2img /sdcard/persist.img /sdcard/persist_EXT4.imgsimg2img /sdcard/persist.img /sdcard/persist_EXT4.img
Thus, weOutS @ 28.07.18, 12:06will convert the very image of the sparse in raw - After all successful write passdd if = / sdcard / persist_EXT4.img of = / dev / block / bootdevice / by-name / persistdd if = / sdcard / persist_EXT4.img of = / dev / block / bootdevice / by-name / persist
With this command, we beg section persist - If all went well the system reboot
Everything has been tested in our unitWhyred , It works, that's a plus sign these guys destroyer71 , Outs , ruslanbolshakov
Post has been editedvolod_bol - 13.10.19, 12:34
Mirror on the official global firmware for Xiaomi Redmi Note 5.
Fastboot installation versions
V9.2.13.0.NEIMIEK
V9.2.4.0.NEIMIEK
V9.2.5.0.NEIMIEK
V9.2.6.0.NEIMIEK
V9.2.7.0.NEIMIEK
V9.5.13.0.OEIMIFA
V9.5.14.0.OEIMIFA
V9.5.17.0.OEIMIFA
V9.5.19.0.OEIMIFA
V9.5.6.0.OEIMIFA
You can download it on thisreference
Post has been editedalibaba2 - 30.07.18, 19:01
Tried TWRP of Red Wolf, or rather a cosmetic fashionXiaomi Redmi Note 5 Global / Note 5 China - firmware MIUI (Post gyord # 73554209)
as well as so called black TWRPXiaomi Redmi Note 5 Global / Note 5 China- unofficial firmware (Post Mr-r00t # 71992837)
I stopped at the black, since it is sewn Ruth (magisk), and a standard design
Fastbut established through both the TWRP, as it is written in the header.Xiaomi Redmi Note 5 Global / Note 5 China - MIUI firmware (Post Camerado # 71285376)
To TWRP not flew after rebooting the phone.
Throw in advance twrp.img file to the root of the file system. After installing TWRP through fastbut not reboot the system. In the established TWRP go to Setup menu, press the bottom right button Img Set, will be able to see your file twrp.img, select it. To put in the window point in the Recovery menu and swipe to make firmware. In the Advanced menu, you can set Magisk for Ruta.
Post has been editedrumyn1976 - 31.07.18, 14:31
as well as so called black TWRPXiaomi Redmi Note 5 Global / Note 5 China- unofficial firmware (Post Mr-r00t # 71992837)
I stopped at the black, since it is sewn Ruth (magisk), and a standard design
Fastbut established through both the TWRP, as it is written in the header.Xiaomi Redmi Note 5 Global / Note 5 China - MIUI firmware (Post Camerado # 71285376)
To TWRP not flew after rebooting the phone.
Throw in advance twrp.img file to the root of the file system. After installing TWRP through fastbut not reboot the system. In the established TWRP go to Setup menu, press the bottom right button Img Set, will be able to see your file twrp.img, select it. To put in the window point in the Recovery menu and swipe to make firmware. In the Advanced menu, you can set Magisk for Ruta.
Post has been editedrumyn1976 - 31.07.18, 14:31
Reason for editing: added
Reset google account
Tested on firmware miui 9.5.6.0 (oeimifa) Android 8
It works only if was not tied to the Mi-account.
It is based on a videohttps://www.youtube.com/watch?v=k47dTfCCSbk
0. The set working sim card into your smartphone
1. connect to Wi fi
2. Press the Add Network
3. instead of the network name, enter Youtube.com
4. highlight the word
5. click on the "Share" icon
6. select the SMS
7. You can enter any number and send
8. Go to the link on YouTube
9. The top entry has an icon in your account on YouTube, there vyberaem confidentiality policy and select an application, "Browser"
10. nahodm on Ineta google account manager 8.apk and set it
11. The return to the browser and find quickshortcutmaker.apk set it and immediately run
11a. through qiuckshortcutmaker go into Settings, About Phone, Tapan on line "version miui" 8 times, go to the advanced settings for developers include oem unlock and do a factory reset
If this does not work, and I can not help being done everything from 1 to 11 points, and do what is written in the 12th.
12. A quickshortcutmaker find Google accounts and choose the line "enter the email address and password," click the button to view and select the "input from a browser"
13. introduce known to you login and password, go back to the beginning at the time of setting Wi fi and agreeing with everything we press all the time "later"
14. We see the desktop, we rejoice, we send the plus my karma
Post has been editedRomabenz - 01.08.18, 22:58
Tested on firmware miui 9.5.6.0 (oeimifa) Android 8
It works only if was not tied to the Mi-account.
It is based on a videohttps://www.youtube.com/watch?v=k47dTfCCSbk
0. The set working sim card into your smartphone
1. connect to Wi fi
2. Press the Add Network
3. instead of the network name, enter Youtube.com
4. highlight the word
5. click on the "Share" icon
6. select the SMS
7. You can enter any number and send
8. Go to the link on YouTube
9. The top entry has an icon in your account on YouTube, there vyberaem confidentiality policy and select an application, "Browser"
10. nahodm on Ineta google account manager 8.apk and set it
11. The return to the browser and find quickshortcutmaker.apk set it and immediately run
11a. through qiuckshortcutmaker go into Settings, About Phone, Tapan on line "version miui" 8 times, go to the advanced settings for developers include oem unlock and do a factory reset
If this does not work, and I can not help being done everything from 1 to 11 points, and do what is written in the 12th.
12. A quickshortcutmaker find Google accounts and choose the line "enter the email address and password," click the button to view and select the "input from a browser"
13. introduce known to you login and password, go back to the beginning at the time of setting Wi fi and agreeing with everything we press all the time "later"
14. We see the desktop, we rejoice, we send the plus my karma
Post has been editedRomabenz - 01.08.18, 22:58
Masik в„ў U 2.2
Updated: August 2, 2018 (12:30)
Greetings, friends: thank_you:
REFERENCE TO POST WITH FIRMWARE
This firmware can be installed on any version of MIUI any status ARB.
Updated the description of the firmware in the corresponding post.
For any question you can always contact me at QMS. Successful use. .
Post has been editedderak1129 - 10.04.19, 19:13
Updated: August 2, 2018 (12:30)
Greetings, friends: thank_you:
REFERENCE TO POST WITH FIRMWARE
This firmware can be installed on any version of MIUI any status ARB.
Updated the description of the firmware in the corresponding post.
For any question you can always contact me at QMS. Successful use. .
Post has been editedderak1129 - 10.04.19, 19:13
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement