Assistant
REPLY |
Soldering station Mypovos 8586 - 2 in 1 - Hair dryer + a soldering iron. 220 V - 750 watts. Selection of a soldering iron, heater. | Technical part, repair, refinement, consumables. |
Message#1 26.02.18, 21:29 | ||
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | Soldering station Mypovos 8586. Analogues of the station: Bakon SBK8586 Soldering Station, Handkskit 8586, Eakins 8586, Newacalox 8586, QSUNRUN 8586, Eruntop 8586. Description Manufacturer: mypovos Output temperature: 100-500 Output power: 750W Temperature resistance: + _5degree Part number: 8586 Input voltage: 220v Soldering iron temperature: 200-480C Hair dryer temperature: 100-500C Consumer heater soldering iron, is relatively expensive, for the money you can buy a soldering iron entirely Model features For 936 soldering stations, hekko 936 and 907 soldering station No. A1321 (for 900m-900l. 907. 908. 913. 914) Power: 50 watts. Voltage: 24 V Heating resistor: 2.5-3. 5 Ohm (Red Line) From a real 5.7 ohm user Sensor Resistor: 43-58 Ohm (Blue Line) From a real 51.3 ohm user Weight: 25 g Instructions Manual for Bakon SBK8586 soldering station aka Mypovos 8586, Handkskit 8586, Eakins 8586, Newacalox 8586, QSUNRUN 8586, Eruntop 8586, etc.Instructions to the soldering station Mypovos 8586.pdf(1.26 MB) Accumulated schemes and algorithm of the soldering station Mypovos 8586 The scheme on the sheet, as on the board, from the User timur21099. Scheme in the Splan program, and the algorithm of work from the User wasser77 The scheme in the Splan program, and the algorithm of work from the User wasser77. thanks to himSoldering station Mypovos 8586 - 2 in 1 - Hair dryer + a soldering iron. 220 V - 750 watts. Selection of a soldering iron, heater. (Post wasser77 # 82034161) Program Scheme Algorithm Fan. Algorithm Fan. When the hair dryer button is turned on, a log.nol appears on the 26th foot of the micron. The MC supplies a 9-foot unit, which turns on the LED of the hairdryer. If the 27-foot (where the reed switch hangs), the weight hangs through the diode, then the 15-foot unit and the heating does not turn on. At 18.19 feet, too, units, than overlaps the flow to the blower fan. Removing the hair dryer from the stand, the weight disappears at 27. MK at 18.19 feet gives zero, which allows the fan to apply voltage in accordance with the position of the speed controller. At 15 foot, it gives the modulated zero, including heating, and begins to control the voltage level on the 23 foot relative to the voltage on the 21 foot. The smaller the difference, the narrower the heat and the lower the heat. When we put the hairdryer on the stand, a mass appears on the 27th leg, a constant unit is supplied to the 15th leg, stopping heating. A unit is fed to the 19th leg, and a zero also hangs on the 18th, which turns the fan on at maximum speed, regardless of the position of the speed controller. As soon as the voltage level reaches 50 feet on the 23rd leg, a unit appears on the 18th leg, which prohibits the fan from supplying voltage to the leg.24 foot, controlling the fan rotation. I can't say how it works, I only know that depending on the speed there rotation, from 1 to 2.5 volts. It is possible that if there is less or more than that, heating of the hair dryer stops .... Also, if you remove the hair dryer from the stand and not having time to heat more than 50 degrees to put it back, the fan twists a certain time according to the regulator. Those. on the 18th and 19th leg, there are zeros and after a while on both legs a unit turns off the fan and displays OFF for a few seconds. Posted 02/04/2019 13:28: Like everything. Now we are waiting for the firmware for a test. I hope we wait Useful Disconnection and assignment of contacts on the hairdryer connector Disconnection and assignment of contacts on the hairdryer connector: 2-3 legs, heater = 88 ohms. 2nd color is gray. 3rd color is white, in the hair dryer through a thermo fuse. 5-8 legs thermo element, at the end of the heater soldering = 1 Ohm, 5th with blue, in a hair dryer turns into red. 8th black, goes to yellow and to the reed switch. 1-7 legs, engine = 1st-red, goes to hair dryer in black, 7th brown, goes to hair dryer in red. 4 foot ground = green, on the body of the dryer. 6 leg reed switch = yellow, the second end of the reed switch goes to the 8th leg. Cost and shops The original is at the time of writing 382 rubles a piece, and is sold in one place: https: //www.aliexpress...-part/32822098417.html A1321 where a lot of sold, and costs about 105 rubles per piece. Such a soldering iron will not work, due to the heater of another, due to the difference in resistance, the appointment of the contacts, different diameters of the contacts. Easily determined by the appearance of the plug. There is another heater, which is suitable for our external, and judging by the numbers, then most likely. Bakon c1321 heater, price in Russia from 165 rubles Installing A1321 directly, without original connector Do at your own risk (do not confuse contacts, contact should not be heated) A1321 is cut with a length of 77 mm, an edge of 7 mm is contact, until the contact is tight in the connector. I'm for the test, just the ends did so, buckled, wave. Paste according to pinout of contacts: I tried it, it works with A1321 100%, try it, I give you an illustrative method, with data. On our soldering iron. Connector: 5-4 contact thermo element = 53 Ohms 1-2 contact heater = 3.5 Ohm 3-pin = ground. Alteration, station refinement It is also desirable to make a small refinement inside the station ... Namely, to install a radiator on the transistor controlling the fan speed of the hairdryer ... It is heating very ... The model is not quite ours but the filling is one-on-one and the transistor is like ours) https://youtu.be/MQGywWIB9j8 Installation of a radiator on this transistor Calibrate the temperature of the hair dryer and soldering iron Need a device to measure temperature. 1 Turn on the soldering station. 2-Turn on the Hairdryer or Soldering Iron (depending on what you need to calibrate) 3-stand up the temperature of 300 degrees. 4-We are waiting for 1 minute for full warm-up. 5-Measure with a third-party device the temperature, say a multimeter with a thermocouple, a hairdryer at a distance of 1 cm, a soldering iron with a drop of tin. 6-Press the + and - buttons at the same time (at the left and middle) at the same time so that the number on the display does not change, hold for a few seconds, the display blinks, the dot starts to run. 7-Configure the existing temperature. IT IS IMPORTANT THAT THE CUSTOMER OR HAIR DRYER BEFORE CALIBRATION INTO ACCOUNT, REACHED THE TEMPERATURE EXPOSED, NEVER INCLUDE THIS SETUP. I learned personally by trial and error. Video instruction:https://youtu.be/Ih513yEAyk4 Hours for flashing the ATMEGA8A-PU microcontroller USB ASP AVR Programmer Description USBasp ISP (in-circuit) programmer for AVR Atmel microcontrollers. The programmer contains a single Atmel ATmega8 microcontroller chip. USB interface is implemented by software. Specifications: Supported Linux, Mac OS, and Windows Operating Systems ATmega8A AU Chip 12,000 MHz Quartz Programming speed up to 5 kBytes / sec Automatic speed control 500mA resettable fuse for protecting computer USB Dimensions 65x20mm male connector 10pin with 2.54mm pitch Layout: 1 MOSI 3 NC 5 / RESET 7 SCK 9 MISO 2 + 5V 4,6,8,10 GND Indication Red LED G - On Red R LED - Data Exchange Jumpers JP2 - POWER 5V / 3.3V Output Voltage Selection JP - SERVICE Firmware Update JP - SLOW Programming at low speeds Supported Microcontrollers AT89S51, AT89S52, AT86RF401, AT90CAN32, AT90CAN64, AT90CAN128, AT90PWM2, AT90PWM2B AT90PWM3, AT90PWM3B, AT90PWM81, AT90PWM216, AT90PWM316, AT90S1200, AT90S2313, AT90S2323, AT90S2343, AT90S4414, AT90S4433, AT90S4434, AT90S8515, AT90S8535, AT90SCR100H, AT90USB82, AT90USB162, AT90USB646 , AT90USB647, AT90USB1286, AT90USB1287, ATmega8, ATMEGA8A, ATmega8U2, ATmega8HVA, ATmega16, ATmega16A, ATmega16HVA, ATmega16HVB, ATmega16M1, ATmega16U2, ATmega16U4, ATMEGA32, ATmega32A, ATmega32C1, ATmega32HVB, ATmega32M1, ATmega32U2, ATmega32U4, ATmega32U6, ATMEGA48, ATMEGA48P, ATmega48PA , ATmega64, ATmega64A, ATmega64C1, ATmega64M1, ATMEGA88, ATMEGA88P, ATMEGA88PA, ATmega103, ATmega128, ATmega128A, ATmega128RFA1, ATmega161, ATmega162, ATmega163, ATmega164P, ATmega164PA, ATmega165, ATmega165P, ATMEGA168, ATmega168P, ATmega168PA, ATmega169 ATmega169P, ATmega323, ATmega324, ATmega324PA ATmega325, ATmega325P, ATMEGA328P, ATmega329, ATmega329P, ATmega406, ATmega640 ATmega644, ATmega644P, ATmega644PA, ATMEGA645 , ATmega649, ATMEGA1280 ATmega1281, ATmega1284P, ATmega2560 ATmega2561, ATmega3250, ATmega3250P, ATmega3290, ATmega3290P, ATmega6450, ATmega6490, ATmega8515, ATmega8535, ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15, ATtiny22, ATTINY24, ATtiny24A, ATTINY25, ATTiny26, ATtiny28 ATtiny43U ATTiny44 ATTINY44A Driver installation under Windows XP From the Thomas Fischl developer USBasp developer site, download the usbasp-windriver driver for Windows. Unzip the archive. Connect your USBasp programmer via USB port to computer. Install the driver. In the device manager, make sure that the USBasp device is installed. Example of use with avrdude under Windows avrdude -pattiny13 -cusbasp avrdude: warning: cannot set sck period. please check for usbasp firmware update . avrdude: AVR device initialized and ready to accept instructions Reading | . | 100% 0.03s avrdude: Device signature = 0x1e9007 avrdude: safemode: Fuses OK avrdude done. Thank you. Under Linux, drivers are not required. Connect USBasp programmer through USB port to computer. At the command prompt, run: lsusb Bus 001 Device 007: ID 16c0: 05dc VOTI shared ID for use with libusb Example of use with avrdude for Linux sudo avrdude -p attiny13 -c usbasp avrdude: warning: cannot set sck period. please check for usbasp firmware update. avrdude: AVR device initialized and ready to accept instructions Reading | . | 100% 0.00s avrdude: Device signature = 0x1e9007 avrdude: safemode: Fuses OK (E: FF, H: FF, L: 7A) avrdude done. Thank you. To work with USBasp programmer not under the superuser, you must install rules 99-USBasp.rules. USBasp.rules can be found in the archive with drivers for windows, diagrams and firmware for the programmer on the site of the developer USBasp programmer Thomas Fischl Before you run the install_rule file, look at which groups you are a member of: groups Then edit the file 99-USBasp.rules: # USBasp - USB programmer for Atmel AVR controllers # Copy this file to /etc/udev/rules.d so # SUBSYSTEM == "usb", ENV {DEVTYPE} == "usb_device", SYSFS {idVendor} == "16c0", SYSFS {idProduct} == "05dc", MODE = "0666" SUBSYSTEMS == "usb", ATTRS {idVendor} == "16c0", ATTRS {idProduct} == "05dc", GROUP = "plugdev", MODE = "0666" adding to the file 99-USBasp.rules your group. After installing the rules, reload all the rules: sudo restart udev Datasheet Datasheet ATMEGA8A-PU - Atmel 8-bit Microcontrollers (MCU) AVR 8 Kb, 512B EE 16 MHz 1 Kb SRAM https: //www.rlocman.ru ...? di = 70755 & / ATMEGA8A-PU Atmel ATMEGA8A-PU Manufacturer: Atmel Description: 8-bit microcontrollers (MCU) AVR 8 Kb, 512B EE 16 MHz 1 Kb SRAM Download Data Sheet:https: //www.rlocman.ru...rs_MCU/ATMEGA8A_PU.pdf Document summary: Features · High-performance, Low-power AVR® 8-bit Microcontroller · Advanced RISC Architecture 130 Powerful Instruments for Single-Cycle Cycle Execution 32 x 8 MIPS Throughput at 16 MHz 2-Cycle Multiplier High-Purity Self-programmable Flash program memory 512 Bytes EEPROM 1K Byte Internal SRAM Write / Erase Cycles: 10,000 Flash / 100,000 EEPROM Data retention: 20 years at 85 ° C / 100 years at 25 ° C (1) Bits · In- Peripheral Features Two-Bit Programmer-Programming-A-On-Chip Programming Programming for Two-Timers / Counters With A Separate Prescaler, One Compare The One-Bit Timer / Counter With A Separate Prescaler, Compare Mode Three PWM Channels 8-channel ADC in TQFP and QFN / ML Specifications: Type of installation: Through Hole Built-in ADC chip: yes Height: 4.57 mm Supply voltage range: 2.7 V ... 5.5 V Length: 34.8 mm Available analog / digital channels: 6 Interface: SPI, TWI, USART Number of I / O lines: 23 Number of timers: 3 Operating temperature range: - 40 C ... + 85 C RAM Size: 1 KB Data ROM Size: 512 B Program Memory Size: 8 KB ADC resolution: 10 bits Processor Series: ATMEGA8x Maximum clock frequency: 16 MHz Enclosure type: PDIP-28 Memory Type: Flash Data bus: 8 bits Width: 7.5 mm Core: AVR RoHS: yes Variants of writing: ATMEGA8APU, ATMEGA8A PU In English: Datasheet ATMEGA8A-PU - Atmel 8-bit Microcontrollers (MCU) AVR 8 Kb, 512B EE 16 MHz 1 Kb SRAM https: //www.radiolocma…? di = 70755 & / ATMEGA8A-PU AVR Development Board (Chip-free) DIY ATMEGA8 ATMEGA48 ATMEGA88 Kit ATMEGA8A-PU ATMEGA8A DIP-28 8-bit with 8 K bytes, programmable flash ATMEGA8 DIP-original The used chips and transistors in the soldering station Mypovos 8586 are similar to the station "Soldering station Bakon SBK8586" Useful links: Soldering station do it yourself Atmega48-88-168-328 https://www.drive2.ru/b/477557208557551830/ http://d-serviss.lv/in…eName=solderingstation Programmers for Atmel microcontrollers. https: //www.radiokot.r…iewtopic.php? p = 1442413 Post has been editedDROND2000 - 04.02.19, 23:39 Reason for editing: Redesigning the header, performed by Nik2001Nik3006 | |
Message#2 26.02.18, 22:49 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 7340 Check in: 13.08.13 LG G3 Dual LTE Reputation: 368 | According to the connectors, the external ones are similar, the difference is metal-plastic, and according to reviews they do not fit the thread. The connectors are all different, but the soldering iron heaters, like the hair dryers, are almost the same everywhere, they are put on models for 20 if not more, in general to use these stations normally, you need a decent refinement -------------------- Stranger John the Ku |
Message#3 26.02.18, 22:55 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | That's the thing. The ceramic heater broke, ordered one, since it is generally for sale alone. But for the future I still want to take a soldering iron, where the heaters are soldered, that is, without a connector. They cost 500 rubles for about five pieces. Therefore, I want to know the details. Here's the voltage, well, and the power, generally neponyatka. -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#4 26.02.18, 22:59 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 7340 Check in: 13.08.13 LG G3 Dual LTE Reputation: 368 | |
Message#5 26.02.18, 23:14 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | I do not have. Only one seller is like that. Five contacts, all involved, on one type of spring. Here is the whole thing. Here it is, the photo from the store. Post has been editedan.andreeff2009 - 22.04.18, 21:27 -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#6 26.02.18, 23:29 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 7340 Check in: 13.08.13 LG G3 Dual LTE Reputation: 368 | A dreary station in terms of repair, the spring housing is most likely, it is easier to replace the whole soldering iron with a maintainable one that costs about 500 rubles, a regular 24 volt soldering iron, resistance ~ 45th Post has been editedBigfishczy - 26.02.18, 23:31 -------------------- Stranger John the Ku |
Message#7 27.02.18, 15:24 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | Found the information, thanks to the owners with Drive2 AlexxNB I measured two resistances there - 51.3 Ohms and 5.7 Ohms. Soldering iron and temperature sensor. My station works without any tricks - I am still pleased with it. Replacing the soldering iron here, if that: ru.aliexpress.com/item/93...ae803_5&priceBeautifyAB=0 mixa8511 Soldering machine red white use from the old ... mixa8511 The heater is ceramics ... Marking a1321 hakko for example, you can take it here ru.aliexpress.com/item/2p…-4fc1-af3f-39c66b4e8521-3 Replacing the heating element ceramic heater core 24 V 50 W A1321 for Hakko 936 937 soldering iron Features of the model: A1321 Ceramic heating element For 936 soldering stations, hekko 936 soldering station and 907 pen No. A1321 (for 900m-900l. 907. 908. 913. 914) Power: 50 W, voltage: 24 V Heating resistor: 2.5-3. 5 Ohm (Red Line) Sensor Resistor: 43-58 Ohm (Blue Line) Weight: 25 g Posted on 02/27/2018 at 15:25: Post has been editedan.andreeff2009 - 22.04.18, 21:25 -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#8 14.04.18, 19:53 | |
Visitor [offline] Group: Users Messages 12 Check in: 26.09.08 Xiaomi Mi 4c Standart Reputation: 0 | Good day. I have a similar situation. Came with a broken heater. I ordered A1321, but the temperature sensor gives an error. Have you approached 1321? |
Message#9 14.04.18, 22:28 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | [email protected], 22:23 Obry day. I have a similar situation. Came with a broken heater. I ordered A1321, but the temperature sensor gives an error. Have you approached 1321? I wrote the original, and a soldering iron + heater A1321. She took a spouse, he left Samara. Original set, works. In the soldering iron that came, I do not know what kind of heater (see photo) there is generally another resistance, and contacts, took it under alteration. And I haven’t yet altered the A1321 to the old connector, only yesterday I arrived at night from Nizhny Novgorod. In the photo I managed to do everything, and all the measurements of resistance. A1321 is suitable, I tested it myself, infa in a hat. There is also a similar station Bakon SBK8586, in the search and score. Post has been editedDROND2000 - 15.12.18, 19:48 -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#10 16.04.18, 09:35 | |
Visitor [offline] Group: Users Messages 12 Check in: 26.09.08 Xiaomi Mi 4c Standart Reputation: 0 | I also ordered the original from the seller, but he never reached ..., I can’t re-order (writes that it is not available), the seller probably banned the dispute. Along the way, our ceramics with a plug is called Bakon c1321, but they are not available on Aliexpress, only on alibaba. most likely, the “pseudo-ceramics” of A1322 came with a “handle” - this is Nichrom, with a thermocouple. Plz tell me the pinout for the dialing of 5 contacts of the original heater, which pair of contacts is heating, and which temperature sensor? maybe I plugged in the wrong way ... Please report the results of modifications. Post has been editedGlukh - 16.04.18, 09:49 |
Message#11 22.04.18, 12:32 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | Plz tell me the pinout for the dialing of 5 contacts of the original heater, which pair of contacts is heating, and which temperature sensor? So in the photo above in the cap everything is painted to the smallest detail, for two soldering irons, ours and the other, with a metal connector. 5-4 contact = 53 Ohm 1-2 contact = 3.5 Ohm 3-pin = ground. See the drawings, I specifically made them for the visual concept, and there the photo of the alteration is clear. -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#12 09.06.18, 14:57 | |
Local [online] Group: Friendssavagemessiahzine.com Messages 111 Check in: 06.02.12 LeEco Le 2 x527 Reputation: 4 | I advise you to score on this station. The firmware flies off from the battery 8. It is unrealistic to find it. The seller either speaks out or turns on a fool. Half a year is a dead monument. How to swing, I will make my fee for this building |
Message#13 01.07.18, 00:38 | |
Local [online] Group: Friendssavagemessiahzine.com Messages 116 Check in: 18.04.17 Oneplus 3T Reputation: 6 | Hi guys, please help. Maybe I'm writing is not in the subject, then I'm sorry. Such a situation, I wanted to assemble a soldering station, I ordered a heat gun on Ali and a heat gun controller board from Kulibin on the Internet. I connected 24 V to the board (Kulibin) 24 V and mixed up the polarity and the capacitor exploded. I know how. I ordered half a year ago, already the ad can not find this Kulibin to ask for the value of the capacitor. Can someone tell the value of the ego? I would be very grateful |
Message#14 01.07.18, 09:37 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 14.05.09 Reputation: 16 | And have to! :) It is better to start by removing the lumps, connect only 24V (correctly) and measure the voltage in the tester where the capacitor was. This will help get rid of further "pyrotechnic" effects, maybe something else has burned. Next, you should choose a new capacitor for a voltage higher than the measured one, and it should be less than 24V, otherwise the stabilizer 317 died. Capacity to choose based on size. Yes, and remember the polarity of the capacitor connection. Post has been editedmuraveiX - 01.07.18, 09:42 |
Message#15 02.07.18, 00:14 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | be less than 24v .... How is it less than 24V? Like to learn from your mistakes and not trust others? -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#16 02.07.18, 11:02 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 14.05.09 Reputation: 16 | So. On a linear stabilizer, something must fall so that it stabilizes. You can find out how much should be on the capacitor by finding out the value of 2 resistors connected to 317. Post has been editedmuraveiX - 02.07.18, 11:03 |
Message#17 03.07.18, 01:41 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | And if it punches there, then the smaller one will bounce again? Maybe all the same (remember there is) at 25 volts? -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
Message#18 03.07.18, 11:12 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 14.05.09 Reputation: 16 | And if the substation? Immediately put on kilovolts? Or will the moon fall to earth? :) Let me remind you that the patient has mixed up the polarity, then you would be better advised the diode. And it is worth making sure that the electrolyte has protected the op amp and the temperature sensor. |
Message#19 12.07.18, 20:16 | |
Visitor [offline] Group: Users Messages 12 Check in: 12.07.18 Reputation: 0 | Dear Sirs, I bought a soldering station in the HK POVOS Electronic Technology Co Ltd. store. Despite the fact that the trade market is 5 years old and has more than 98% positive feedback, it is extremely dishonorable. The station worked for about 2 weeks and began to issue nonsensehttps://www.youtube.com/watch?v=6rZCuqSgvv8The seller offered to send the station for repair and indicated email mail. The video that they presented with the problem (malfunction) could not be opened for viewing. Fought with them for a very long time, useless. The fault is clearly with the Atmega8 microcontroller. I ask these guys, (I apologize, but I cannot otherwise) send the firmware or the wired Atmega, it is useless, and then they stopped communicating altogether. It is a dead weight. Maybe someone has a scheme of this soldering station, please inform me or reset the link to the scheme. Help with the MK firmware for this soldering station. |
Message#20 12.07.18, 20:22 | |
Visitor [offline] Group: Users Messages 12 Check in: 12.07.18 Reputation: 0 | Where to get the firmware for this soldering station. My firmware has flown away. Monster of Chinese industry is a dead weight. |
Message#21 14.07.18, 02:19 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 356 Check in: 05.02.12 Reputation: 27 | Having understood I realized that my programmer will not work. It seems there is infa. [email protected], 00:48 I will try to sew once. The programmer pickit2 + pickit3 is called let's see. Once disassembled, at the same time from fotkal, and added all the chips and transistors in the cap. CPU: ATMEL 1636 AT MEGA8A-PU Buy let's say here: https: //ru.rsdelivers...id=3962755582514963488 Here is info: https: //www.radiokot.r…iewtopic.php? p = 1442413 And here: https: // invalid link / blog / ebay / 36603.html -------------------- Alcatel one touch pop3 Model-5025D Prots-MTK 6580 4 cores RAM-1GB Memory phone-4gB Androyd-5.1 * # * # 82533284 # * # * |
mobile version | Now: 04/18/19, 16:28 |