Tp-Link Archer C60 - Discussion | [Wifirouter]: 450Mb \ s - 867Mb \ s | 4x100Mb
Good afternoon, requested all sizes quickly customize let pliz fully with antennas, spread out horizontally - the overall length and width. I want to hang vertically in a niche (I know that there are no fasteners) - overall dimensions needed with antennas. thank you very much
Hello forum users recently bought a router archer c60 ru ver 2.0 settings at power off are reset to the factory on the 5GHz Net unstable switched to 2.4 GHz covering poor old dlink dir615 covered even a little better. What could be the problem.
skDD Why drop settings do not know. C 5 2.4 ..... try to reduce the width of the channel, set less than 80 Posted on 15/08/2018, 21:41:
tripleclick , Mikrotik hap AC2 .... 4 internal antenna. Without glitches and places at times less. We are pleased to sell to your right nowskDD @ 15.08.18, 20:21
Hello forum users recently bought a router archer c60 ru ver 2.0 settings at power off are reset to the factory on the 5GHz Net unstable switched to 2.4 GHz covering poor old dlink dir615 covered even a little better. What could be the problem.
when he first hooked up, phones xiaomi seen 5GHz thought router buggy, and no phone does not support the upper frequency (channel), the default channel was a gun, put the 36 channel and phones saw 5GHz network, then not very far to break through to 80MHz, I put the channel width to 40 MHz and is normal. Try to play settings.
Bad that the phone does not put in the 5GHz priority if two networks in the phone settings are automatically connected, the phone that he wanted it, and selects, as a result the frequency of 2.4 GHz is necessary to remove the phone to connect automatically or turn it off on your router.
Post has been editedramak - 17.08.18, 16:10
S48GS, Sorry, I'm a beginner, wanted to put build your own, do not tell me how it differs from what is currently on the site openwrt (18.06.0)?
In addition to supporting version py, what difference?
Post has been editedsonerise - 18.08.18, 03:47
sonerise, in my post the RC2 18.06 collected for a couple of days before the 18.06
version in my post you can obnovtsya at 18.06
Unlike that version of "off site" you just can not put on the RU version of the C60 router
the reason I described in my post
Tell me, fool as from a router to do this, an access point? That he caught another Wi fi router and distributed, thanks in advance
I post the firmware for pouring from under the TFTP to Archer C60 (RU) v1.0
It has everything you need in the archive ...
the necessary arrangements:
turn offfirewall, Pull outWAN port cable provider.
run the ftpd server, network card192.168.0.66/255.255.255.0Select the correct network interface is configured ftpd server.
then you need when you turn on the router and press the Reset WPS.
if you did everything right to see the progress of the firmware on the router casting for a couple of seconds.
and after a few minutes you will receive OpenWRT 18.06.1 (standart ip 192.168.1.1)
P.S. thankS48GS , For the tip. Only he lecturing firmware for Archer C60 (RU) v2.0
OpenWRT_18.06.1_firmware_for_Archer_C60 (RU) v1.zip(4.16 MB)
Post has been editedstar_vision - 20.08.18, 22:15
It has everything you need in the archive ...
the necessary arrangements:
turn offfirewall, Pull outWAN port cable provider.
run the ftpd server, network card192.168.0.66/255.255.255.0Select the correct network interface is configured ftpd server.
then you need when you turn on the router and press the Reset WPS.
if you did everything right to see the progress of the firmware on the router casting for a couple of seconds.
and after a few minutes you will receive OpenWRT 18.06.1 (standart ip 192.168.1.1)
P.S. thankS48GS , For the tip. Only he lecturing firmware for Archer C60 (RU) v2.0
Attached files
OpenWRT_18.06.1_firmware_for_Archer_C60 (RU) v1.zip(4.16 MB)Post has been editedstar_vision - 20.08.18, 22:15
I was given
objective: to make of the router simply switch to wifi.
Turning off dhcp server is stuck in another lan port router, with wifi dhcp, but the traffic does not go, the traffic through the guest operating point.
What am I doing wrong?
Hardware Version: Archer C60 v2.0
Software Version: 2.0.0 Build 20161206 rel.60287
Software Version: 2.0.0 Build 20161206 rel.60287
objective: to make of the router simply switch to wifi.
Turning off dhcp server is stuck in another lan port router, with wifi dhcp, but the traffic does not go, the traffic through the guest operating point.
What am I doing wrong?
igran @ 21.08.18, 18:44
objective: to make of the router simply switch to wifi.
Turning off dhcp server is stuck in another lan port router, with wifi dhcp, but the traffic does not go, the traffic through the guest operating point.
What am I doing wrong?
Turning off dhcp server is stuck in another lan port router, with wifi dhcp, but the traffic does not go, the traffic through the guest operating point.
What am I doing wrong?
I have everything working on such a scheme ... But you're probably on the ip router changes from 0.1 to 0.2
Post has been editedpredator212 - 22.08.18, 19:36
predator212 @ 22.08.18, 19:35
I have everything working on such a scheme ... But you're probably on the ip router changes from 0.1 to 0.2
predator212 I addressing 192.168.1.0/24
small animal was assigned 192.168.1.254
and does not work
Post has been editedigran - 23.08.18, 23:11
igran , Should work ... Throw to the factory and the mood again. Give this address 1.2. and on the router with an Internet forbid the distribution dhcp 1.20-1.254S48GS thank you so much.
Router C60V2 RU. I alter under openwrt and updated to 18.06.1. And as we now leave to drain, if anything?
Router C60V2 RU. I alter under openwrt and updated to 18.06.1. And as we now leave to drain, if anything?
oneunit, if you're talking about the original firmware is most likely to OpenVRT menu "Flash new firmware image" just give firmware from off site (Russian version of the C60 only), I have not tested it but probably it works
100% working firmware via tftp server quote
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download<FIRMWARE>and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~ 15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~ 30 second to complete recovery
1. Set PC to fixed IP address 192.168.0.66
2. Download<FIRMWARE>and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~ 15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~ 30 second to complete recovery
"Wrong" (with the wrong device ID) firmware on the router or pour through OpenWRT or through tftp impossible after the reboot to attempt to fill the wrong firmware does not break and will last business firmware
S48GS, Thank.
"And will be working past the flashing"
This, I realized, when flooded with openwrt off. site, until I found this forum. I am afraid, suddenly Potro downloader? There was a sad experience with archer c20v1. 18.06.0 poured it on tftp and he died.
Yet found, it is advised to throw firmware in the router and give the command.Here.
But in the flash will not be the place, or if the directory / tmp, it is written in the ram?
star_vision @ 20.08.18, 20:22
I post the firmware for pouring from under the TFTP to Archer C60 (RU) v1.0
It has everything you need in the archive ...
the necessary arrangements:
disable the firewall, remove from the WAN port of the cable provider.
run the ftpd server, network card in 192.168.0.66/255.255.255.0, select the correct network interface settings in the ftpd server.
then you need when you turn on the router and press the Reset WPS.
if you did everything right to see the progress of the firmware on the router casting for a couple of seconds.
and after a few minutes you will receive OpenWRT 18.06.1 (standart ip 192.168.1.1)
P.S. Thank S48GS, for the tip. Only he lecturing firmware for Archer C60 (RU) v2.0
It has everything you need in the archive ...
the necessary arrangements:
disable the firewall, remove from the WAN port of the cable provider.
run the ftpd server, network card in 192.168.0.66/255.255.255.0, select the correct network interface settings in the ftpd server.
then you need when you turn on the router and press the Reset WPS.
if you did everything right to see the progress of the firmware on the router casting for a couple of seconds.
and after a few minutes you will receive OpenWRT 18.06.1 (standart ip 192.168.1.1)
P.S. Thank S48GS, for the tip. Only he lecturing firmware for Archer C60 (RU) v2.0
Thank star_vision and S48GS! I can not enhance the reputation, few posts)
I can only add that: on firmware Archer C60 (RU) _V1_160805 the procedure failed!
However, the firmware Archer C60 (RU) _V1_171107 loader via TFTP is in broken condition. Necessarily retraces firmware flashing at 160,805 in openwrt!
S48GS, All is excellent, returned to the drain, even all the settings are preserved at the drain. Through tftp. Although through the same tftp he killed archer c20v1, tried to openwrt gash.
Greetings
But there is a solution that would have 2.4 speed does not cut it? In openwrt is there?
Post has been editedSanserif - 28.08.18, 13:01
But there is a solution that would have 2.4 speed does not cut it? In openwrt is there?
Post has been editedSanserif - 28.08.18, 13:01
Hello everyone! Something happened to routerom.Set visible connection passes. BUT! On chastotet 5 Ghz not want to work. Outgoing speed with different devices according to the spidtestam 0! At 2.4 Ghz and the cable is no problem. Reset reconfigures etc. I put the test firmware from here. The result is the same. Dead transmitter 5ghz?
Speed ​​racing too in 2 times less than conventional steel.
Post has been editedqent1n - 31.08.18, 19:24
 |
Speed ​​racing too in 2 times less than conventional steel.
Post has been editedqent1n - 31.08.18, 19:24
Reason for editing: adding a screen test
©savagemessiahzine.com2005-2021 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement