Beeline SmartBox One - discussion пїЅ
usbmodem wifirouter: 2.4GHz (300Mbit \ s) - 5GHz (300Mbit \ s) | 4 • 100Mbit \ s | USB: 1




Post has been editedstp101 - 20.05.19, 23:24

And what about this gadget no longer any movements? Maybe there is firmware, where?

There are firmware, but there is no bootloader ...

Sew exclusively through the programmer

Tell me how much dBm on the antennas of the router

Lastdenc7,
Thank you, this is a long time ago, but in stock it only works with the biline, and the beeline in our region is weak on the home Internet. Two houses are connected and only in the center)). I will see how to flash it through the programmer.

Watch in joy , Maybe I will make you very happy, but this device has a “superuser”
See below ...: blush:: thank_you:

Post has been editedLastdenc7 - 12.11.17, 01:57

Hi people.
The topic has been lying for a long time, but some still do not know about the existence of SuperUser in this router.
The super user allows you to change the operator, connect via Telnet and SSH, in general, "Full Root".

Following this incomprehensible and slightly open instruction, you will have the opportunity to change the Biline L2TP to any other suitable Internet communication protocol for you.

Post has been editedLastdenc7 - 12.11.17, 01:50

Lastdenc7,
Just in the hole!

box one cuts the speed of the cord. firmware v2.0.20. Speedtest directly shows 94-95 mb / s through a router 30-32. Can be corrected?

jovialkent What kind of firmware is this? on off site last 2.0.14


Post has been editedleva.ryzhkov - 17.11.17, 22:59

Changed the port to lan 2, the speed leveled off with the stated. Returned lan 1 speed is identical to direct connection. Issue resolved

leva.ryzhkov
https: //omsk.beeline.r...beeline-smart-box-one/

Who will tell you how to make a wi-fi distribution from a modem from the Huawei 3372 beeline on this router? )))

Does no one really know if it is possible to flash the Smart box one for another firmware? I'm already on the forumhttp://ingodwetrust.ru/openwrt-flashing/I found the bootloader, but I do not know what to do, can someone tell me?
smartbox-to-boot_97d.img(20.73 KB)


Post has been editedWrathjr - 28.11.17, 14:39

Wrathjr , try blocking the router's firmware block by block, and pouring the bootloader through the face, at least with n300 it worked


* As far as I know, this boot loader does not fit our n320 (if you sew a face through the web)

Post has been editedLastdenc7 - 28.11.17, 23:12

Can someone tell me how to block advertising addresses on this Router?

In the comments, this Kredov seems to have said that it is sewn without problems ... Yes, I would be satisfied if someone could use the factory img image to edit it to save the 3G connection settings, then the modem will probably work: happy:

The people, who has a flash dump? A flash drive is buggy I can not collect a full-fledged dump, then it will be cut off, then it will be cut off.

I decided to contact the operator of the biline, wrote to the post office, the girl finally called, who as usual asked if I set up the modem correctly, the router and so on, eventually made up an application and passed it to the technical specialists, a couple of hours later I called The technical specialist, who has already asked a few other questions, eventually said that he would send the application to the developers of the biline software. After 1 hour I called the technical specialist about again and said that unfortunately they do not provide for the router to work with 4G modems<_<

From the backup found on the Internet, the merged via putty collected a dump and stitched a flash. Fixed wan-mac, serial, wifi name and password. On your own.
Now the dances are more fun, by dhcp I get ip, dns. But the l2tp muzzle says that it cannot resolve the name of the vpn server, that is, the problem with getting dns. Already tried everything. Who had such a problem, please share the experience))
I will add about the bootloader from n300, I flashed it according to the rules 20 times (by the programmer), but the router simply did not start, all the lamps were burning and that's it. I also tried to collect openwrt dump merged with n300. On my copy did not work. Iron is simply not initialized. Maybe it's in the difference between the RAM chips, or something else.
You can analyze the dependence on the revision boards. But modem owners are not very sociable, information is difficult to gather.

Post has been editedcartanman - 01.12.17, 03:11

If anyone is interested, I received a response from Credov by e-mail. In short, the modem is not worth the perversion, it's easier to buy a normal one)

Good day! img the image of the original firmware is compiled code, and if you can edit it is not an easy task, then I can not help you. I stitched my ONE through the Chinese programmer. After flashing it will have 3G modems. But I don’t even remember how to reflash it)) long ago it was