Digma DIVISION 100 - Discussion | IP-Network camera Digma DiVision 100 - a small device that m



Rep: (0)
DiscussionWiFi IP camera Digma DiVision 100
Official site | Discussion пїЅ

Attached Image
Attached Image

Device photos
Attached Image
Attached Image

Device description
The Digma DiVision 100 IP Network Camera is a small device that can be installed on any flat surface or hung from a wall. It does not need a lot of wires, because it connects to your home network using the built-in Wi-Fi adapter.

Always high-quality image. The device is equipped with a photosensitive CMOS-matrix, a glass lens with a double infrared filter and infrared LEDs. It can get a clear, detailed picture in any conditions - from bright sunlight to full darkness.
Simple control. To gain access to the video and camera settings, just use the user-friendly web interface or a proprietary mobile application.
Full security. In the case of a motion sensor, the camera will send a warning signal to the user and a freeze frame of events in the room.

Device characteristics
Specifications


Camera type - color
Lens focal length (mm) - 2.8-2.8
Execution - internal
Lens angle of view (В°) - 80
Night shooting distance (m) - 5
Matrix Type - CMOS
IR LED - yes
Night Vision - Yes
Wi-Fi (802.11) - b, g, n
Videotape
Video Resolution - 1280x720
Video transfer rate (fps) - 25
Memory
Memory Card Type - MicroSD

Dimensions
Height (mm) - 120
Width (mm) - 80
Thickness (mm) - 80
Weight (g) - 130
Other
Guarantee period - 1 g.
Additionally

Gain control

Flare compensation

Microphone

Manufacturer - Digma
Country of origin - China

Additional Information

  • Before posting read the message Video section rules
  • Messages that are not related to the topic of discussion (offtopic) are deleted without warning.

There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonPictureunder the messages to which you want to add links.



Rep: (0)
Good day, dear forum users! I would like to offer a Digma DiVision 100 IP camera to discuss WiFi ... I hope to find here highly qualified specialists in video surveillance equipment and security systems. Your experience and knowledge, I think, will be useful not only for me, but also for all the "happy" owners of this device ...

I have a problem: today DiVision 100 went out and did not turn on any more (the period of use is a little less than six months). The indicator is very dim (the red indicator of the camera is barely lit). The power supply unit of the device is working fine ... the phone has charged it :). Who thinks what? What are the recommendations?



Rep: (9)
There is an AI pi camera, according to Wai Fayu, it is tied to the router. when the Internet is distributed to the smartphone in the same network, I see an image from this camera. but as soon as I leave the apartment - nothing, only messages come. How to watch an image via LTE? In the settings there are settings for ftp b ddns, but they are empty. as I understand it, I need to register ports or ah pi or something else, but how to do it?
googled, need external ah pi. without it will not work?



Rep: (0)
kiloHerz @ 10/09/17, 18:47*
There is an AI pi camera, according to Wai Fayu, it is tied to the router. when the Internet is distributed to the smartphone in the same network, I see an image from this camera. but as soon as I leave the apartment - nothing, only messages come. How to watch an image via LTE? In the settings there are settings for ftp b ddns, but they are empty. as I understand it, I need to register ports or ah pi or something else, but how to do it?
googled, need external ah pi. without it will not work?


What camera? Firm? Model?



Rep: (9)
on Digma DiVision 100. The problem is that the router is not with white ah pi. I don't want to pay for it yet. Is there an opportunity to configure via cloud storage? tried yesterday, but could not. The IVideon router saw the program, but the camera does not (. In the smartphone application there is no such possibility?



Rep: (0)
kiloHerz @ 10.10.17, 11:13*
on Digma DiVision 100. The problem is that the router is not with white ah pi. I don't want to pay for it yet. Is there an opportunity to configure via cloud storage? tried yesterday, but could not. The IVideon router saw the program, but the camera does not (. In the smartphone application there is no such possibility?


To connect and use this camera there is no need to get a white IP. Information on this issue can be viewed at the link:http://digma.ru/catalog/item/2172/#. You can also download the application DIGMA SmartCam. With other applications, the camera will not work! Another application is designed for a computer - a client for P2P connection from a PC, version 2.0.7.0 (it can be downloaded there) ... using a corporate client for a PC).



Rep: (9)
Ibideon installed on ib, it all worked



Rep: (0)
kiloHerz @ 10.10.17, 18:55*
Ibideon installed on ib, it all worked


How much is IVideon better than a proprietary application? And how protected are files in the cloud storage? Is there a chance that someone will merge video from YouTube to YouTube for example?



Rep: (9)
I look through the digm program from ap story. On the first day, she didn’t work for me at the lte and wai fae outside the house. so I had to stir up with invideo. it all worked. so didn’t do anything else in the program, thank you



Rep: (3)
M
The topic has been moved to the "IP cameras пїЅ.



Rep: (0)
I have a problem. This camera does not see the Kingston microSD card on 16Gb. Windows 7 also does not see it, but Windows 10 has found it. Formatted in different formats, in one does not see (writes "the card is not inserted" when it is inserted). Is this some kind of love of this camera for these cards or something else?

Post has been editedmelkobrat - 27.12.17, 15:18



Rep: (0)
I have a problem. This camera does not see the Kingston microSD card on 16Gb. Windows 7 also does not see it, but Windows 10 has found it. Formatted in different formats, in one does not see (writes "the card is not inserted" when it is inserted). Is this some kind of love of this camera for these cards or something else?


Maybe a defective card ... and maybe a camera ... In general, this model is very buggy .. I took a few pieces and passed everything under warranty ... The service center concluded that the cameras were not repairable and the store just returned the money ... I do not recommend buying this camera! And in general, Digma is the worst of all Chinese.



Rep: (0)
I got a camera yesterday. I configured to record both on the invision and on the memory card (SanDisk 16gb, FAT32, there was a glitch when I pulled out the card while recording with the camera on it, that neither the camera nor the laptop wanted to see the card, inserted the card back into the camera and restarted it, the map is seen everywhere.)
All set up, put on the record. Somewhere after 7 hours of continuous recording, the Wi-Fi fell off, respectively, the recording on the invision stopped, (perhaps the problem is in the router, it used to be stupid with Wi-Fi, I will try to replace the router). But, the recording continued on the memory card.
To restore the connection, I had to restart the camera.

Post has been editedSnov9 - 31.12.17, 08:32



Rep: (0)
Snov9 @ 12/31/17, 09:31*
I got a camera yesterday. I configured to record both on the invision and on the memory card (SanDisk 16gb, FAT32, there was a glitch when I pulled out the card while recording with the camera on it, that neither the camera nor the laptop wanted to see the card, inserted the card back into the camera and restarted it, the map is seen everywhere.)
All set up, put on the record. Somewhere after 7 hours of continuous recording, the Wi-Fi fell off, respectively, the recording on the invision stopped, (perhaps the problem is in the router, it used to be stupid with Wi-Fi, I will try to replace the router). But, the recording continued on the memory card.
To restore the connection, I had to restart the camera.


If the camera is under warranty, it is better to hand it over quickly and get the money ... anyway, this crap will not work normally :( My first job was half a year ... the rest fell down during the week ...



Rep: (1)
I have a problem with this camera, it is not periodically visible from the network when connected via LTE. When you connect to it via WiFi (where the camera is located), then everything is OK, then you go through LTE and the camera is not visible.
Most likely this is because of the Chinese server. Who knows, is it possible to connect to it via another application on the host (I have a DDNS provider)? Ivideon will work, as I understand it, only if the server is constantly running on the computer, but I don’t want it.

Maybe someone will need information: the camera on the Internet is hanging on port 81 (I could not find this anywhere else until I scanned the router to which the camera is connected). I connected to it through a browser on a PC on a white IP and changed the port to a convenient one for me.

The quality of this device: junk is still, the quality of the picture is not very good, the sound is online with an echo somehow, the application on the smartphone is very raw (plays recorded over time, the camera is visible through LTE also through time), you need to play videos through the corporate application.

Post has been editedlinus87 - 05.01.18, 15:55



Rep: (0)
I thought to take the guarantee, but decided that I would wait. I do not want to give up just like that, but try different things.

I turned off the built-in IR illumination, the camera began to write around the clock. There are failures, minutes, but maybe the router still crashes, I have an old one.

I registered on invidione, bought a business account there for 3 months. 7 days of recording has already happened.
He hacked the camera to the service through the invidion server and the webmord of the camera:
http: // ip-cameras: 81 / videostream.cgi? loginuse = login & loginpas = password

The webmord itself in Chinese or English, there is an opportunity to download instructions, and the necessary software.

I normally connect to the camera via Invidion and DigMav software, both from the computer and the site, and from the smart.

Discovered sound problems: strong interference. No noise suppression and echo suppression. I think this will be a good reason for returning the camera, since I need a normal microphone.

Another problem: Invision does not capture the sound from the camera, but it is in the recordings on the memory card, and goes to the smartphone.

Periodically, the time or time zone was lost, I did not know how to set up the sales.

Through DeviceClient you can view camera settings. But be sure to click Refresh in each section of the settings.
It turned out that the camera can have three users: the administrator, the operator, and the visitor (visitor), but did not configure the latter, maybe it does not work normally.

Post has been editedSnov9 - 07.01.18, 14:57



Rep: (1)
The problem is that the camera is not online from the phone is solved by rebooting it remotely via the web, but you understand that it is not convenient to do it every time.



Rep: (0)
Did anyone set up DynDNS on the camera itself? I did not succeed, I tried through NOIP. If anyone knows how to do it correctly, then please instructions. The DiVision 200 camera, but they differ only in the presence of a turning mechanism.

Post has been editedKot-tolik - 10.01.18, 10:26



Rep: (70)
Kot-Tolik @ 01/10/18, 10:22*
DiVision 200 camera

This is for you in this topic -WiFi IP cameras on the Ingenic T10 processor (I21AG, HX-I2110T2, HW0036 and others)



Rep: (0)
Thanks for the link, but I did not see the instructions for setting up DynDNS. I just can’t understand whether I need to configure the router by port forwarding or not, since the camera itself supports the dynamic dns service. I registered for NOIP, entered my login, password and the name of my host into the camera, she ate it all, but when clicking on the link to my host browser it says that such a page doesn’t exist or is not available



Rep: (70)
Kot-Tolik @ 11.01.18, 15:09*
I need to configure the router for port forwarding or not

It is not necessary to configure on the camera, almost every router has a dyndns service, you can configure it, you can request a service - a static ip-address. There are many options, if only the provider does not use nat (otherwise a bummer).
Port forwarding to the camera is necessary.
Does it even make sense to bother? through the digma smartcam application, everything works fine through the cloud, and I want to remind DiVision 200 again on the T10 chip, more information has been gathered in that topic.


Full version    

Help     rules

Time is now: 18/09/19, 16:27