Except yourself, no one will help you.
Here on the forum, only suggest and set a direction
can. And then it all depends on you.

Posted on 03/11/2019, 12:21:

There were such. Search in the branch.

I don’t have any adhesive tape at all, hooked on the sealing gum and that’s all - it’s holding on, I’m already using the second mirror ...

And purely theoretically, could this preloader be saved separately, before all the manipulations, when the mirror was still in the original version? I have so far the same as freeman22s, and yet: and if your preloader does not fit ours, then maybe ours should not fit yours (mirror)? But remember later, I got the firmware from the flash drive ... And then what was left of the old one so that it could start normally?

To start. There is no "yours" yet. There is a backup preloader freeman22s,
You, it is not necessary that the mirror is like his.
And the manifestations of the problem are completely different. 28% have not yet been explained.
Preloader from freeman22s, Fits any T10-based mirror.
But on boards without support for power measurement, it will bring up a menu that will create problems.
The problems are serious but not "brick".
This is our old one (such as in a hat) does not fit on boards
with nutrition control, not the other way around. Otherwise, I would delete it immediately from the branch,
and would give only in PM.
All who did full backup saved it and not even theoretically.
It could be saved separately. Having made a backup user_boot
There is no point.Flash drive firmware does not overwrite the old preloader.
He stayed.
Find the cause of 28%, eliminate it if possible.
And do not confuse what happens infreeman22s, with that
what is going on with you. These are two big differences.
I wouldn’t like to punish, but you have a memory, I’m afraid “smiled”.

This scatter will leave only 4 GB user.
Maybe he will save you.MT6735_Android_scatter.rar(1.08 KB)


Post has been editedBezrazniti - 11.03.19, 14:34

freeman22s,
Let’s do what we do.
Just as you described how you killed the mirror,
Now once again write about why the backup does not fill up.
And that you tried to fill it.

Bezrazniti,

I have so far (based on what I did,I requested the preloaderand logo) there is a big suspicion of Preloader.
And either the manufacturer or someone with the same mirror from the forum can give it to me.
All these days sat on different branchsavagemessiahzine.comand other forums, the preloader contains eMMC parameters and something else that is not clear to me, I studied the internals of the preloader from our branch, it has a mention of Kingston 08EMCP08_EL3AV100. I looked at other preloaders for telephone processes 6735, similar but ...

There is even the sad thought of ordering another mirror and removing the preloader from it, leaving a new one to sell, but it does not allow sobriety of the mind.

In general, my head began to hurt every day, I was upset :(

P.S. But I won’t give up, I will continue to dig further!

Posted on 03/11/2019, 14:46:



Backup is poured, everything goes well, but the mirror hangs on the boot screen (logo)


Post has been editedfreeman22s - 11.03.19, 14:50

Absolutely bad thought. I don’t believe in it myself. But ...
Is the short circuit connected? Are both wires yellow and red connected to + 12V?
And +12 is there? By default, your mirror at +12.4 should be cut off.
Try another PSU.

Bezrazniti,


KZH is not connected (when the mirror was working, it worked without it).
Both wires are connected to +, black to -.
In the electric network of a car, it is 14.9 V, in the mirror description it is written that it works in the range of 12-24 V.
I connect a screwdriver to the battery, it is 12 in.

In the description, another interesting fact is written - ROM: 16GB (System will occupy 3GB) is the system.img section?

Posted 11/03/2019 at 15:58:

Bezrazniti,


Attached a photo of the power supply and battery

Nothing .... They may not provide inrush currents.
Connect to the on-board network.
Yes. But not only.

Posted on 03/11/2019, 16:08:

Do you see the difference between "work" and "initialize"?

Those. directly to the battery of a car?

Can you connect a car to a battery charger?


In the description - Power supply External power supply

BMW line power supply; Supply voltage: 9V-25V

Post has been editedfreeman22s - 11.03.19, 16:10

Not all chargers give direct current.
Rather, on the contrary, almost everyone has a pulsating one.
There is even more interesting ... “restoring” the floor period charge,
gender period discharge .... Apparently you are not very with electricity ...
Do not take chances. Turn on the mirror in the car.

Bezrazniti, In the meantime, there are no options with the board, I'm looking at options with usb regs for GU on android. It seems that these look promising (and the price is not killer):


What do you think, if you take everything related to camera initialization from their apk, add it to our dvr.apk, everything will work, up to adas, perhaps?

If we take it, then do not add, but instead set it.
I would not spend money. Can't normal camera + math
cost $ 13 - 15 Just can not, even among the Chinese.

Lexville ,
There is a new mainland t98-v2. 3
AutoSmart (mirror on Android) E06 (T98) from Phisung - Discussion (Post by Dilen # 78209910)

Dilen, where were you, friend .. had to order yourself 3.1 from china ..

I agree and do not expect the image better than from the standard one, or rather I don’t even expect the same as from the standard one, the optics are already clearly weaker. Just a budget option. Yes, and I doubt that you can get better from usb

Posted on 03/11/2019, 18:30:


Where and how much?

I can’t backup.
In the device manager, the mirror is not defined as described in the header, the inscription: ADB interface comes out, and portable device E appears

Junsun k755 T10

Lexville Selina, $ 65

I ended up attaching my camera to the ceiling sheathing. I still did not like the option with the glass mount, because the camera with the mount will close the review.

TorroRosso, and what version (revision) has come? I just have V2.4, I would not really like to lower it, it is better to increase it.