RoverPad Air Q8 3G- Talk | Tablet, 8 "
Thank you, ibanit. Filled firmware from DEXP Ursus N180 in RoverPad Air Q8 3G, everything works. Flooded in order to "close the advertising holes" in your own software. It helped. It works really stable, in my subjective feeling, even better than it was.
Guys, there's somebody original firmware for this device? The one from dekspa - does not arise. Error _Repartition_.
ibanit That's fucking it was not compatible! Now it is brick, which now refuses to be sewn!
uart send error when trying skonnektitsya.
You can do anything? No one knows?!
Attached images
 |
Post has been editednitroski - 23.10.19, 16:26
nitroski, Message: "[Removed] Failed: uart send error" in the status bar.
Reason: the firmware process was interrupted.
Decision:
Try a different PC, port or cable.
Update flash driver.
Try holding “Volume Down” while connecting or “Volume Up”.
Maybe the USB port on the phone is broken, replace it.
Charge the battery (via frog)
den_wel Thank you, I've seen it in the subject line of flashers.
Unfortunately, the tablet initially sew correctly. After flashing Passed inscription appeared.
By the way, the tablet is fully working, as it turned out, except for the screen. He, apparently, the other, so there is a stripes.
Re too it is impossible to flash. When clamping volume minus and connect the tablet falls off the device udps in my case. And flasher writes uart send error. Thereafter Comporta simply drops out of the device manager.
On the whole, the tablet works. I turn it off at random through touch.
But how to flash again I do not know. Tomorrow I'm going to pick on.
Flasher latest version
Post has been editednitroski - 23.10.19, 19:19
nitroski @ 23.10.19, 19:40
That's fucking it was not compatible! Now it is brick, which now refuses to be sewn!
Problems in handles obvious. Here athumaneverything went well. Personally she also raised the tablet.
Try to swing the battery before flashing, re-supply all the drivers and usethis flasherRather than the latest version. You can try more of twenty DIGMa. He works problem.
Attached files
Digma_Spreadtrum_Tools_R20.rar(10.3 MB)Post has been editedibanit - 24.10.19, 12:30
den_wel Thank. But. Sew Sew, but the screen strips remain. Not suitable for this screen. Damn, well for the revision I have this ?!
Posted on 24/10/2019, 12:28:
ibanit Android plows. Firmware for the screen (((
Attached images
 |
Post has been editednitroski - 24.10.19, 12:31
nitroski, , Dak look for serial number, in the same specified range for which it is suitable And can see the iron, connector and cable
Post has been editedden_wel - 24.10.19, 12:34
And look where audit fees? This is not what ?! The serial number on the board is not found.
It looks like it to me someone has deciphered.
Zephyr checked - all the rules.
Post has been editednitroski - 24.10.19, 12:42
It looks like it to me someone has deciphered.
Zephyr checked - all the rules.
Attached images
 |
 |
Post has been editednitroski - 24.10.19, 12:42
nitroski @ 24.10.19, 16:38
And look where audit fees?
Most likely the reverse side. It happens more often trail departs matrix. I would have shrugged it on both sides.
ibanit The board on the other side. Help, pzhlst)))
Plume in order. I twitched - the same thing. This is after the firmware from the N180 just begun. Before that it was the rules.
Try to swing the battery before flashing, re-supply all the drivers and to use the flasher, but not the latest version. You can try more of twenty DIGMa. He works problem.
I Tried. I tired of it yesterday. All stitches. The screen is not suitable
Attached images
 |
Post has been editednitroski - 24.10.19, 12:52
ibanit UserData try without flash?
UPD. I sew without User Data. also strip
Attached images
 |
Post has been editednitroski - 24.10.19, 13:18
ibanit Nea ... pancake (((
I tried to selectively firmwarehttps://yadi.sk/d/GG2W...0%B8%D0%B2%D0%BA%D0%B8
If the firmware is not compatible everywhere writes section
Attached images
 |
Post has been editednitroski - 24.10.19, 13:32
nitroski, You can still apply to this topic. What would have collected under appropriate auditDevelopment and porting for devices on the Spreadtrum SC7731 platform
Now try this yet.
Post has been editedibanit - 24.10.19, 13:44
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement