Assistant
REPLY |
Orange Pi Zero Plus 2 - discussion | [SBC] Allwinner H3 |
Message#1 22.03.17, 19:45 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 198 Check in: 17.03.12 Xiaomi Redmi 3S Reputation: 11 | Orange Pi PC 2 | Orange pi zero | Orange pi lite | Orange pi prime | Orange Pi Plus | Orange Pi 2G-IOT | Orange Pi Zero Plus 2 | How do I get an Orange Pi? Orange Pi Zero Plus 2 Specifications CPU: Allwinner H3 Quad-core Cortex-A7 GPU: Mali400MP2 GPU Memory (SDRAM): 512MB DDR3 (shared with GPU) Onboard Storage: TF card (Max. 64GB) / eMMC flash (8G) Onboard WIFI: AP6212, IEEE 802.11 b / g / n, BT4.2 Power Source: USB OTG can supply power Video Interface ASCI 880B CMOS sensor interface, Supports CCR656 protocol for NTSC and PAL, Supports SM pixel camera sensor, Supports video resolution up to 1080p @ 30fps Video Outputs: Supports HDMI output with HDCP, Supports HDMI CEC, Supports HDMI 30 function Low-level peripherals: 26 Pins Header, compatible with Raspberry Pi B +, 13 Pins Header, with 2x USB, IR pin, AUDIO (MIC, AV) GPIO (1x3) pin: UART, ground. LED: Power led & Status led Supported OS: Android, Ubuntu, Debian, Rasberry Pi Image Useful links: Appeared on sale new baby, Orange Pi Zero Plus 2. Littledetails. Post has been editedstp101 - 10.04.18, 23:26 |
Message#2 23.03.17, 16:18 | |
Starche)) [offline] Group: Friendssavagemessiahzine.com Messages 1627 Check in: 13.01.08 Xiaomi Mi Max Standard Reputation: 113 | Bites. For open, you can also have the good old pipc)))) and here there is no lan port, and this is important for media or the same iptv |
Message#3 23.03.17, 17:27 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 887 Check in: 29.03.09 Reputation: 66 | Rather, the car pc, why it’s unclear for the media center, when there are analogues and a bit cheaper and more functional for the media center ... And so, more models, good and different ... In general, in 2017, the modular single-board trends are gaining popularity ( Of course, the board will no longer be one, but the dimensions are exactly sbc). And now this is interesting and in general, very similar to the evolution of desktops. When xunlong comes to this, gash budget decisions will be very different. I bought a "base PCB" and modules, I do not need elec, but I need additional gpio and energy saving cpu please, etc. |
Message#4 23.03.17, 17:32 | |
Starche)) [offline] Group: Friendssavagemessiahzine.com Messages 1627 Check in: 13.01.08 Xiaomi Mi Max Standard Reputation: 113 | I would take a new one for elec too, on the A64, there is at least a gigabit lan, plus a video of Mali400, and it is already tested in the tree. |
Message#5 23.03.17, 17:51 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 198 Check in: 17.03.12 Xiaomi Redmi 3S Reputation: 11 | I understand the target audience of OpenELEC? Has anyone ordered already? Cool toy, but the price bites ... or so it seems to me? what is good: yAP6212AThere is BT 4.2 for all sorts of smart gadgets, FM though the antenna is not divorced, but it's not a problem to solder, I wonder if I2S and PCM are divorced. Well and most importantly, flash MLC emmc 5.0, imho should be faster than ordinary memory cards. For myself, I see only one thing, if wifi is normal to use as a prefix for old TVs without smart tv, there will be the very thing, everything is on board. You need a radiator, power supply and hdmi cable, screwed to the back of the TV and ready. Regarding AP6212, I understand the difference from the AP6212A in BT 4.2 or not? Post has been editedquick31 - 23.03.17, 20:04 -------------------- |
Message#6 24.03.17, 08:57 | |
Starche)) [offline] Group: Friendssavagemessiahzine.com Messages 1627 Check in: 13.01.08 Xiaomi Mi Max Standard Reputation: 113 | |
Message#7 24.03.17, 11:50 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 198 Check in: 17.03.12 Xiaomi Redmi 3S Reputation: 11 | |
Message#8 27.03.17, 14:07 | |
Starche)) [offline] Group: Friendssavagemessiahzine.com Messages 1627 Check in: 13.01.08 Xiaomi Mi Max Standard Reputation: 113 | Haaah. Just put on the shelf an upgrade zeroshki, to H5 protsa |
Message#9 17.04.17, 03:56 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 31.08.15 Reputation: 44 | Appeared yet Orange Pi Zero Plus 2 H5 Quad-core Wifi Bluetooth who can be lazy can create Temko |
Message#10 18.04.17, 12:03 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 31.08.15 Reputation: 44 | Here is a mirror for downloading official images of distribution kits (firmware) Orange Pi Zero +Orange Pi Zero Plus2 h3 + h5+ short description https://orangepi0.github.io/ PS: since their canoes are swinging badly - I think the mirror will not be superfluous, I only scanned Orange Pi Zero h2 + h3 + h5 |
Message#11 26.04.17, 21:54 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 186 Check in: 10.06.08 Apple iPhone 4S Reputation: 15 | Today I bought this board with an H3 processor When you connect the power without a microSD card in the debug console, it displays the following listing HELLO! BOOT0 is starting! boot0 version: 4.2.0 boot0 commit: c8c201b51b7ea1baa94590a1887313124d9a5879 fel_flag = 0x00000000 rtc [0] value = 0x00000000 rtc [1] value = 0x00000000 rtc [2] value = 0x00000000 rtc [3] value = 0x0000000f rtc [4] value = 0x00000000 rtc [5] value = 0x00000000 rtc [6] value = 0x00000000 rtc [7] value = 0x00000000 DRAM DRIVE INFO: V1.4 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 NOT GATE MODE READ DQS LCDL = 001c1c1d DRAM Type = 3 (2: DDR2.3: DDR3.6: LPDDR2.7: LPDDR3) DRAM CLK = 672 MHz DRAM zq value: 003b3bfb DRAM dram para1: 10f20200 DRAM dram para2: 00000001 DRAM workmode1: 000009f4 DRAM SIZE = 512 M odt delay dram size = 512 card boot number = 2 card no is 2 sdcard 2 line count 8 [mmc]: mmc driver ver 2015-04-13 16:07:39 [mmc]: *** Try SD card 2 *** [mmc]: mmc 2 cmd 8 err 00000100 [mmc]: mmc 2 cmd 8 err 00000100 [mmc]: mmc 2 send if cond failed [mmc]: mmc 2 cmd 55 err 00000100 [mmc]: mmc 2 cmd 55 err 00000100 [mmc]: mmc 2 send app cmd failed [mmc]: *** Try MMC card 2 *** [mmc]: mmc re-update_phase [mmc]: mmc re-update_phase [mmc]: 8bit ddr !!! [mmc]: mmc re-update_phase [mmc]: MMC ver 5.0 [mmc]: SD / MMC Card: 8bit, capacity: 7456MB [mmc]: vendor: Man 00150100 Snr 0075a84e [mmc]: product: 8WPD3 [mmc]: revision: 5.2 [mmc]: *** SD / MMC 2 init OK !!! *** sdcard 2 init ok The size of uboot is 000e4000. sum = 4655330c src_sum = 4655330c set_mmc_para, sdly 50M 0 set_mmc_para, sdly 25M 0 Succeed in loading uboot from sdmmc flash. Ready to disable icache. Jump to secend Boot. SUNXI_NORMAL_MODE [0.275] e mode U-Boot 2011.09-rc1-00024-gdbed064 (Nov 30 2015 - 20:18:20) Allwinner Technology [0.284] version: 1.1.0 [0.287] uboot commit: dbed064f3b1a936e4e374a6284944f4e4e30e9ae not using multi config normal mode [0.300] pmbus: ready not set main pmu id axp_probe error [board_vendor] vid_used not used [0.318] PMU: pll1 1008 Mhz, PLL6 = 600 Mhz AXI = 336 Mhz, AHB = 200 Mhz, APB1 = 100 Mhz sid read already fel key new mode run key detect no key found no key input dram_para_set start dram_para_set end normal mode [0.349] DRAM: 512 MiB relocation Offset is: 15af1000 [box standby] read rtc = 0xf [box_start_os] mag be start_type no use user_gpio config user_gpio ok gic: normal or no secure os mode workmode = 0 MMC: 2 [0.428] [mmc]: mmc driver ver 2015-06-1 20:01:00 [0.433] [mmc]: get sdc_phy_wipe fail. [0.437] [mmc]: get sdc0 sdc_erase fail. [0.441] [mmc]: get sdc_2xmode ok, val = 1 [0.445] [mmc]: get sdc_ddrmode ok, val = 1 [0.449] [mmc]: get sdc_f_max fail, use default 50000000Hz [0.455] [mmc]: get card_line ok, card_line = 8 [0.459] [mmc]: get sdc_ex_dly_used fail, use default [0.464] [mmc]: SUNXI SD / MMC: 2 [0.478] [mmc]: * Try SD card 2 * [0.481] [mmc]: mmc 2 cmd 8 err 100 [0.487] [mmc]: mmc send if cond failed [0.491] [mmc]: mmc 2 cmd 55 err 100 [0.496] [mmc]: send app cmd failed [0.499] [mmc]: * Try MMC card 2 * [0.539] [mmc]: mmc re-update_phase [0.544] [mmc]: mmc re-update_phase [0.549] [mmc]: mmc re-update_phase [0.554] [mmc]: ddr8 [0.556] [mmc]: mmc re-update_phase [0.573] [mmc]: CID 0x15010038 0x57504433 0x520075a8 0x4ebb7351 [0.578] [mmc]: MMC ver 5.0 [0.581] [mmc]: mmc clk 50000000 [0.584] [mmc]: SD / MMC Card: 8bit, capacity: 7456MB [0.589] [mmc]: boot0 capacity: 4000KB, boot1 capacity: 4000KB [0.595] [mmc]: *** SD / MMC 2 init OK !!! *** [0.600] [mmc]: erase_grp_size: 0x400WrBlk * 0x200 = 0x80000 Byte [0.605] [mmc]: secure_feature 0x55 [0.609] [mmc]: secure_removal_type 0x9 [0.613] sunxi flash init ok script config pll_de to 864 Mhz Not Found clk pll_video1 in script script config pll_video to 297 Mhz script config pll_periph0 to 600 Mhz [boot] disp_init_tv [DISP_TV] disp_init_tv enter g_tv_used screen TV support TV TYPE! [BOOOT_DISP_TV] disp tv device_registered unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu] enable power vcc-hdmi-18, ret = -1 DRV_DISP_Init end error: open tv_vdid.fex, maybe it not exist read byte = 10 [get_display_resolution] = 404 read byte = 10 [get_display_resolution] = 20b boot_disp.auto_hpd = 1 auto hpd check has 100 times! auto check no any connected, the output_type is 4 [1.991] finally, output_type = 0x4, output_mode = 0x4, screen_id = 0x0, disp_para = 0x0 In: serial Out: serial Err: serial -------- fastboot partitions -------- -total partitions: 14- -name- -start- -size- bootloader: 1,000,000 1,000,000 env: 2,000,000 1,000,000 boot: 3,000,000 1,000,000 system: 4000000 30000000 misc: 340000000000 recovery: 35000000 2000000 sysrecovery: 3.7 billion 30000000 private: 6,700,000,000 Reserve0: 68000000 1000000 klog: 69000000 1000000 Reserve1: 6,000,000,000 2,000,000 Reserve2: 6c000000 cache: 6d000000 28000000 UDISK: 95000000 0 ----------------------------------- base bootcmd = run setargs_nand boot_normal bootcmd set setargs_mmc key 0 cant find rcvy value cant find fstbt value misc partition found to be run cmd = run setargs_mmc boot_normal read item0 copy0 Item0 (Map) magic is bad the secure storage item0 copy0 is bad read item0 copy1 Item0 (Map) magic is bad the secure storage item0 copy0 == copy1, the data is good Item0 (Map) magic is bad the secure storage map is empty no item name mac in the map sunxi storage read no item name wifi_mac in the map sunxi storage read no item name bt_mac in the map sunxi storage read no item name specialstr in the map sunxi storage read no item name serialno in the map sunxi storage read check user data form private the user data'magic is bad WORK_MODE_BOOT adver not need show sunxi_bmp_logo_display f_read btr over hd12896 read byte = 3686456 [2.213] screen_id = 0, screen_width = 0, screen_height = 0 [2.218] frame buffer address 46400036 [2.222] Hit any key to stop autoboot: 0 read boot or recovery all [2.383] sunxi flash read: offset 3000000, 13369855 bytes OK [2.392] ready to boot board_display_setenv: disp_para = 0 init_disp = 20b0404 tv_vdid = 0 [2.400] [mmc]: mmc exit start [2.414] [mmc]: mmc 2 cmd 8 err 100 [2.419] [mmc]: mmc send if cond failed [2.423] [mmc]: mmc 2 cmd 55 err 100 [2.428] [mmc]: send app cmd failed [2.440] [mmc]: get sdc_phy_wipe fail. [2.444] [mmc]: get sdc0 sdc_erase fail. [2.448] [mmc]: get sdc_2xmode ok, val = 1 [2.452] [mmc]: get sdc_ddrmode ok, val = 1 [2.456] [mmc]: get sdc_f_max fail, use default 50000000Hz [2.461] [mmc]: get card_line ok, card_line = 8 [2.466] [mmc]: get sdc_ex_dly_used fail, use default [2.471] [mmc]: mmc 2 exit ok [ 2.474] Starting kernel ... [sun8i_fixup]: From boot, get meminfo: Start: 0x40000000 Size: 512MB ion_carveout reserve: 160m @ 0 300m @ 0 130m @ 1 200m @ 1 ion_reserve_select: ion chipid [0x2c00081! ion_reserve_common: ion reserve: [0x56000000, 0x60000000]! [0.980347] ls_fetch_sysconfig_para: type err device_used = -1063782316. [0.988905] tscdev_init: tsc driver is disabled [0.995800] [cpu_freq] ERR: get cpu extremity frequency from sysconfig failed, use max_freq [1.017847] sunxi_oops: heming add OOPS_INFO_ADDR = -20 [1.680749] ths_fetch_sysconfig_para: type err device_used = 1. [1.695772] init: init proc start [1.703924] init: could not import file '/init.debug.rc' from '/init.sun8i.rc' [1.712233] init: *************************** LOW MEM DEVICE DETECT [1.718908] init: ******************************* add swapon_all success [1.726278] init: ******************************* add write success [1.791064] init: open path: / dev / bus / usb / 001/001 [1.942225] init: start e2fsck listening ... [1.971260] init: open path: / dev / bus / usb / 002/001 [2.111203] init: open path: / dev / bus / usb / 003/001 [2.263853] init: open path: / dev / bus / usb / 004/001 [2.411179] init: open path: / dev / bus / usb / 005/001 [2.561132] init: open path: / dev / bus / usb / 006/001 [2.946900] init: C_IN_START [2.949965] init: path = / dev / block / by-name / cache [2.955260] init: C_IN_START [2.958493] init: path = / dev / block / by-name / UDISK [3.067002] fs_mgr: Unable to open zram conf device / sys / block / zram0 / disksize [3.075150] init: defined DONT_SHOW_INITLOGO [3.080778] init: / sys / class / switch / cvbs / state is exist [3.081307] init: dont need format / dev / block / by-name / private [3.093104] init: The device is low memory 495 [3.145714] Failed to get mali parameter! [3.241841] [SPDIF] sunxi-spdif cannot find any using configuration for controllers, return directly! [3.260363] [SPDIF] sndspdif cannot find any using configuration for controllers, return directly! [3.312779] init: get_disp_policy: 1 for modify configs.dhd_module_init: in [3.376315] [VFE_ERR] vfe sensor register check error at input_num = 0 [3.399464] init: single_display_policy exit @@@@ wifi_platform_bus_enumerate device present 1 [3.841924] init: untracked pid 104 exited [3.876631] healthd: Could not open / sys / class / power_supply [3.879591] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [3.892348] healthd: No charger supplies found [3.961904] android_usb: already disabled [3.966642] init: using deprecated syntax for specifying property 'sys.usb.config', use $ {name} instead [3.978087] init: using deprecated syntax for specifying property 'sys.usb.config', use $ {name} instead root @ dolphin-fvd-p1: / # [10.359989] init: no such service 'dhcpcd_' [19.016625] init: sys_prop: permission denied uid: 1003 name: service.bootanim.exit [20.936670] [BT_LPM] bluesleep_get_uart_port: bluesleep_get_uart_port get uart_port from blusleep_uart_dev: uart, port irq: 33 [30.960031] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [30.966706] [BT_LPM] bluesleep_tx_timer_expire: Tx data during last period [41.000037] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [41.006714] [BT_LPM] bluesleep_tx_timer_expire: Tx data during last period [51.040048] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [51.046728] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle [51.053628] [BT_LPM] bluesleep_sleep_work: going to sleep ... At the same time, the processor is very hot OS version is extremely cropped. No fdisk and many useful programs. There is dd and potentially it can be used to install the image from the card to NAND memory Post has been editedKudryashovDA - 26.04.17, 22:15 -------------------- HTC WildFire ->Iphone 4S ->Iphone 5s |
Message#12 26.04.17, 22:51 | |
Visitor [offline] Group: Active users Messages 23 Check in: 17.03.15 Samsung Galaxy Tab 4 10.1 SM-T531 Reputation: 1 | Yesterday I also launched this one, BF and even Blue seems to work, put her on a Diet, does not eat much and heats 40C in total. Everything is installed mc, openssh, node-red nov and tp. http://dietpi.com/down...usH3-armv7-(Jessie).7z |
Message#13 27.04.17, 11:55 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 186 Check in: 10.06.08 Apple iPhone 4S Reputation: 15 | I confirm, DietPi works. Wifi module is determined, programs are installed. Today a distribution kit from Armbian has been released for this board -Ubuntu xenial Put - works, and WiFi with Bluetooth too :) And through the menu armbian-config, you can transfer the system to the internal memory with one (three) clicks and release the card. There is no normal Debian Jessi from Armbian yet. The one that for NanoPi Neo Air is set up and turns smartly, but Wifi does not work - there is no device wlan0 Post has been editedKudryashovDA - 27.04.17, 12:29 -------------------- HTC WildFire ->Iphone 4S ->Iphone 5s |
Message#14 28.04.17, 06:35 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 198 Check in: 17.03.12 Xiaomi Redmi 3S Reputation: 11 | KudryashovDA, Is it possible to check how fast wifi works compared to XR819? Also interesting is the speed of the eMMC. Post has been editedquick31 - 28.04.17, 06:36 -------------------- |
Message#15 28.04.17, 11:49 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 186 Check in: 10.06.08 Apple iPhone 4S Reputation: 15 | OrangePi Zero Plus 2 Test Board with H3 Processor Installed nightly assembly ARMBIAN 5.27.170428 nightly Ubuntu 16.04.2 LTS 3.4.113-sun8i System installed on internal memory (microSD removed) Iphone power adapter - 5V 1A Communication with the board via the debug Com-port. Distance to Wifi router 4 meters in line of sight Link Quality = 5/5 Signal level = -55 dBm Noise level = -91 dBm Encryption router WPA2-PSK / AES Ping to the router # ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56 (84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq = 3 ttl = 64 time = 3005 ms 64 bytes from 192.168.0.1: icmp_seq = 4 ttl = 64 time = 2009 ms 64 bytes from 192.168.0.1: icmp_seq = 5 ttl = 64 time = 1012 ms 64 bytes from 192.168.0.1: icmp_seq = 6 ttl = 64 time = 13.0 ms 64 bytes from 192.168.0.1: icmp_seq = 8 ttl = 64 time = 4111 ms 64 bytes from 192.168.0.1: icmp_seq = 13 ttl = 64 time = 3.96 ms 64 bytes from 192.168.0.1: icmp_seq = 14 ttl = 64 time = 10.4 ms ^ C --- 192.168.0.1 ping statistics --- 14 packets transmitted, 7 received,50% packet loss, time 13013ms rtt min / avg / max / mdev = 3.966 / 1452.419 / 4111.302 / 1522.897 ms, pipe 5 Turning off power saving mode iwconfig wlan0 power off # ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56 (84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq = 5 ttl = 64 time = 42.3 ms 64 bytes from 192.168.0.1: icmp_seq = 6 ttl = 64 time = 2.81 ms 64 bytes from 192.168.0.1: icmp_seq = 7 ttl = 64 time = 2.10 ms 64 bytes from 192.168.0.1: icmp_seq = 8 ttl = 64 time = 1.90 ms 64 bytes from 192.168.0.1: icmp_seq = 9 ttl = 64 time = 2.00 ms 64 bytes from 192.168.0.1: icmp_seq = 10 ttl = 64 time = 2.55 ms 64 bytes from 192.168.0.1: icmp_seq = 11 ttl = 64 time = 4.07 ms 64 bytes from 192.168.0.1: icmp_seq = 12 ttl = 64 time = 2.68 ms 64 bytes from 192.168.0.1: icmp_seq = 13 ttl = 64 time = 1.92 ms 64 bytes from 192.168.0.1: icmp_seq = 14 ttl = 64 time = 1.89 ms 64 bytes from 192.168.0.1: icmp_seq = 15 ttl = 64 time = 3.95 ms 64 bytes from 192.168.0.1: icmp_seq = 16 ttl = 64 time = 1.94 ms 64 bytes from 192.168.0.1: icmp_seq = 17 ttl = 64 time = 14.7 ms 64 bytes from 192.168.0.1: icmp_seq = 18 ttl = 64 time = 1.83 ms 64 bytes from 192.168.0.1: icmp_seq = 19 ttl = 64 time = 1.88 ms ^ C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 15 received,21% packet loss, time 18021ms rtt min / avg / max / mdev = 1.837 / 5.909 / 42.355 / 10.232 ms Better, but packets are still lost at the very beginning. We look at the frequency settings of the processor # cpufreq-info | grep 'The governor' The governor of "interactive" may decide The governor of "interactive" may decide The governor of "interactive" may decide The governor of "interactive" may decide We set the frequency to a maximum without the right to reduce it. # cpufreq-set -g performance # cpufreq-info | grep 'The governor' The governor of "performance" may decide The governor of "performance" may decide The governor of "performance" may decide The governor of "performance" may decide Pinging the router again # ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56 (84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq = 1 ttl = 64 time = 1.57 ms 64 bytes from 192.168.0.1: icmp_seq = 2 ttl = 64 time = 4.14 ms 64 bytes from 192.168.0.1: icmp_seq = 3 ttl = 64 time = 1.20 ms 64 bytes from 192.168.0.1: icmp_seq = 13 ttl = 64 time = 40.3 ms 64 bytes from 192.168.0.1: icmp_seq = 14 ttl = 64 time = 1.39 ms 64 bytes from 192.168.0.1: icmp_seq = 15 ttl = 64 time = 1.62 ms 64 bytes from 192.168.0.1: icmp_seq = 16 ttl = 64 time = 1.28 ms 64 bytes from 192.168.0.1: icmp_seq = 17 ttl = 64 time = 1.59 ms 64 bytes from 192.168.0.1: icmp_seq = 24 ttl = 64 time = 43.6 ms 64 bytes from 192.168.0.1: icmp_seq = 25 ttl = 64 time = 1.89 ms 64 bytes from 192.168.0.1: icmp_seq = 26 ttl = 64 time = 1.57 ms ^ C --- 192.168.0.1 ping statistics --- 26 packets transmitted, 11 received,57% packet loss, time 25017ms rtt min / avg / max / mdev = 1.208 / 9.113 / 43.622 / 15.525 ms Pings go immediately, but after the 17th package failure Built-in memory card test $ armbianmonitor -c $ HOME Starting to fill / dev / mmcblk0p1 with test patterns Free space: 5.74 GB Creating file 1.h2w ... OK! Creating file 2.h2w ... OK! Creating file 3.h2w ... OK! Creating file 4.h2w ... OK! Creating file 5.h2w ... OK! Creating file 6.h2w ... OK! Free space: 369.04 MB Average writing speed: 5.07 MB / s Now verifying the written data: SECTORS ok / corrupted / changed / overwritten Validating file 1.h2w ... 2097152/0/0/0 Validating file 2.h2w ... 2097152/0/0/0 Validating file 3.h2w ... 2097152/0/0/0 Validating file 4.h2w ... 2097152/0/0/0 Validating file 5.h2w ... 2097152/0/0/0 Validating file 6.h2w ... 805952/0/0/0 Data OK: 5.38 GB (11291712 sectors) Data LOST: 0.00 Byte (0 sectors) Corrupted: 0.00 Byte (0 sectors) Slightly changed: 0.00 Byte (0 sectors) Overwritten: 0.00 Byte (0 sectors) Average reading speed: 74.96 MB / s Starting iozone tests. Be patient, this can be a long time to complete: Iozone: Performance Test of File I / O Version $ Revision: 3.429 $ Compiled for 32 bit mode. Build: linux Contributors: William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Fri Apr 28 08:34:36 2017 Include fsync in write timing O_DIRECT feature enabled Auto mode File size set to 102400 kB Record Size 4 kB Record Size 512 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 512k -r 16M -i 0 -i 1 -i 2 Output is in kBytes / sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride read fwrite recw write rewrite read rewrite read fwrite frewrite 102400 4 3306 6788 16663 16704 14080 5673 102400 512 23504 7239 78147 78176 77426 5280 102400 16384 6611 7120 69150 80337 80041 7237 iozone test complete. The results from testing / dev / mmcblk0p1 (ext4): Data OK: 5.38 GB (11291712 sectors) Data LOST: 0.00 Byte (0 sectors) Average writing speed: 5.07 MB / s Average reading speed: 74.96 MB / s random random reclen write read rewrite read read read 4 3306 6788 16663 16704 14080 5673 512 23504 7239 78147 78176 77426 5280 16384 6611 7120 69150 80337 80041 7237 Health summary: OK Performance summary: Sequential reading speed: 74.96 MB / s 4K random reading speed: 14080 KB / s Sequential writing speed: 5.07 MB / s (low) 4K random writing speed: 5673 KB / s To interpret the results alternatives please refer tohttp://oss.digirati.com.br/f3/and also http: //www.jeffgeerlin...pberry-pi-microsd-card andhttp: //thewirecutter.c...ews/best-microsd-card/ While conclusions about WIFI is difficult to do. The assembly appeared only yesterday. -------------------- HTC WildFire ->Iphone 4S ->Iphone 5s |
Message#16 28.04.17, 20:23 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 186 Check in: 10.06.08 Apple iPhone 4S Reputation: 15 | Addition to the previous post It turned out to start normally WIFI # ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56 (84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq = 1 ttl = 64 time = 6.96 ms 64 bytes from 192.168.0.1: icmp_seq = 2 ttl = 64 time = 14.9 ms 64 bytes from 192.168.0.1: icmp_seq = 3 ttl = 64 time = 15.0 ms 64 bytes from 192.168.0.1: icmp_seq = 4 ttl = 64 time = 29.1 ms 64 bytes from 192.168.0.1: icmp_seq = 5 ttl = 64 time = 9.44 ms 64 bytes from 192.168.0.1: icmp_seq = 6 ttl = 64 time = 11.0 ms 64 bytes from 192.168.0.1: icmp_seq = 7 ttl = 64 time = 2.90 ms 64 bytes from 192.168.0.1: icmp_seq = 8 ttl = 64 time = 14.6 ms 64 bytes from 192.168.0.1: icmp_seq = 9 ttl = 64 time = 13.3 ms 64 bytes from 192.168.0.1: icmp_seq = 10 ttl = 64 time = 11.2 ms 64 bytes from 192.168.0.1: icmp_seq = 11 ttl = 64 time = 9.04 ms 64 bytes from 192.168.0.1: icmp_seq = 12 ttl = 64 time = 6.60 ms 64 bytes from 192.168.0.1: icmp_seq = 13 ttl = 64 time = 15.5 ms 64 bytes from 192.168.0.1: icmp_seq = 14 ttl = 64 time = 14.5 ms ^ C --- 192.168.0.1 ping statistics --- 14 packets transmitted, 14 received, 0% packet loss, time 13022ms rtt min / avg / max / mdev = 2.901 / 12.468 / 29.117 / 5.916 ms You need to create a file with the setting of the broadcasting grid of your country. I have it like this: # cat /lib/firmware/ap6212/config.txt ccode = RU regrev = 0 The build is no longer nightly, normal with today's update. Welcome to ARMBIAN 5.27 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i -------------------- HTC WildFire ->Iphone 4S ->Iphone 5s |
Message#17 01.05.17, 08:48 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 31.08.15 Reputation: 44 | Orange Pi Zero Plus 2 Schemes (pdf + djvu) https://orangepi0.github.io/#schemes https://github.com/ora...PI-ZERO-PLUS2_V1_0.pdf https://github.com/ora...I-ZERO-PLUS2_V1_0.djvu Post has been editedhyphop - 02.05.17, 05:44 |
Message#18 01.05.17, 19:57 | |
Novice [offline] Group: Active users Messages 41 Check in: 02.12.07 HP Elite X3 Reputation: 0 | Hello! Has anyone tried to install the official build of the bucket 0.8.0? Not a great connoisseur of the latter, but after installation it does not look functional. Icons netfliksa, YouTube, etc. after clicking just update the screen. And after updating the shell, it stops even opening settings at all. Crooked up or without gaps will not work? I took it just to play, and maybe I'll put it on cooling and make a tvbox ... well, or a Wi-Fi adapter for the camera ... |
Message#19 01.05.17, 22:34 | |
Novice [offline] Group: Active users Messages 41 Check in: 02.12.07 HP Elite X3 Reputation: 0 | Understood. There is no software, so it flies. Strange system, set the shell, and do not install the software to which the shell refers ... |
Message#20 02.05.17, 20:48 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 31.08.15 Reputation: 44 | Is it possible to check how fast wifi works compared to XR819? Also interesting is the speed of the eMMC. Wifi is better but not great! up to 6000Kb works - eMMC is a class here - it makes any external flash drives even more expensive - for such ridiculous money it is super !!! root @ miZy: ~ # dd if = / dev / mmcblk1 bs = 1M of = / dev / null count = 100 100 + 0 records in 100 + 0 records out 104857600 bytes (100.0MB) copied, 2.100021 seconds, 47.6MB / s if you raise the frequency root @ miZy: ~ # dd if = / dev / mmcblk1 bs = 10M of = / dev / null count = 100 100 + 0 records in 100 + 0 records out 1048576000 bytes (1000.0MB) copied, 16.940254 seconds, 59.0MB / s and if you still lift root @ miZy: ~ # dd if = / dev / mmcblk1 bs = 10M of = / dev / null count = 100 100 + 0 records in 100 + 0 records out 1048576000 bytes (1000.0MB) copied, 14.740120 seconds, 67.8MB / s I think you can reach up to 70-80MB / s Post has been editedhyphop - 04.05.17, 15:56 |
Message#21 02.05.17, 21:10 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 402 Check in: 31.08.15 Reputation: 44 | My dream come true! today I checked i2s - and it works !!! - on daudio1 - both din and dout - fiddling around with soldering is a little bit just soldering 4 wires to the necessary conclusions of the AP6212 - (to crawl properly, it was necessary to strain - for me it is small) i2s_mclk = port: PG10 i2s_bclk = port: PG11 i2s_dout0 = port: PG12 i2s_din = port: PG13 the other day lay out the details! It seems to me a great device for audio application |
mobile version | Now: 04/28/19, 17:58 |