Volume up through engineering MTK menu
Be careful-picking in the engineering menu, you can commit follies, will only firmware through FlashTool backup or restore.
View engineering MTK menu
To access the engineering menu * # * # 3646633 # * # *
Scroll through the tab HardwareTesting
1. Increase the ringer volume:
Go to the Audio>Loudspeaker mode
Type Select the Ring (ring)
choose Level 6
Value is set to 250 click Set
Max Vol. set 155 (na160 podhripyvaet) press Set
2.Povyshenie earpiece volume (during a conversation):
Go to the Audio>Normal mode
First, set up a general volume modulation.
Select Type: Media
Then in the Max Vol section. set the volume to 160 and click Set.
Next, change the speaker volume settings.
Select Type: Sph
Next, we will change the Level - This signal levels.
What would be clear - there are seven levels and each corresponds to one "click" the volume rocker, which side of the phone.
Using this rocker when talking, you essentially iterate through these signal levels.
Those. Level 0 is the most "quiet" position rocker, Level 6 - the "loud".
The value of the volume level for each Level is located in Value is cell (0 ~ 160). And it should be changed.
Changing is simple - erase the old value, enter the new one and press the Set button (next to the cell).
Warning! Write down the factory numbers before changing!
Enter the following Values ​​is values:
Level 0 - 90 click Set
Level 1 - 100 click Set
Level 2 - 110 click Set
Level 3 - 120 click Set
Level 4 - 130 click Set
Level 5 - 140 click Set
Level 6 - 160 click Set
Max Vol values. 0 ~ 160 we have already changed earlier.
3.Chuvstvitelnost microphone:
Whatever evidence you have entered automatically at all positions the volume rocker will work only one minimum of all specified.
Therefore, the readings of Level 0 ~ 6 are the same.
Go to the Audio>Normal mode
Select Type: Mic
Warning! Write down the factory numbers before changing!
Enter the following Values ​​is values:
Level 0 - 220 click Set
Level 1 - 220 click Set
Level 2 - 220 click Set
Level 3 - 220 click Set
Level 4 - 220 click Set
Level 5 - 220 click Set
Level 6 - 220 click Set
Level 7 - 0, click Set
Level 8 - 0, click Set
Level 9 - 0 click Set
Level 10 - 0 click Set
Level 11 - 0 click Set
Level 12 - 0 click Set
Level 13 - 0 click Set
Level 14 - 0 click Set
If a phone call from your partner complains that he could hear his echo, then you put too high readings microphone sensitivity, they should be lower.
Try to change instead of 220 to 200 or 180 for a start. Values ​​can be within 140 ~~ 250. Here you can experiment a little.
It all depends on how much quality microphone on the phone.
Also, when setting this parameter, the volume of sound recording will depend on when shooting a video or a voice recorder.
4.Povyshenie volume multimedia (external speaker):
Go to the Audio>Normal mode
Type: Media
Enter the following Values ​​is values:
Level 0 - 142 press the Set
Level 1 - 158 press the Set
Level 2 - 158 press the Set
Level 3 - 158 press the Set
Level 4 - 170 press the Set
Level 5 - 170 Set push
Level 6 - 158 Set push
Level 7 - 0, click Set
Level 8 - 0, click Set
Level 9 - 0 click Set
Level 10 - 0 click Set
Level 11 - 0 click Set
Level 12 - 0 click Set
Level 13 - 0 click Set
Level 14 - 0 click Set
5.Povyshenie volume multimedia (headphones):
Go to the Audio>HeadSet Mode
Type: Media
Enter the following Values ​​is values:
Level 0 - 15 press the Set
Level 1 - 30, press the Set
Level 2 - 45 press the Set
Level 3 - 60 press the Set
Level 4 - 75 press the Set
Level 5 - 90 press the Set
Level 6 - 105 Set push
Level 7 - 120 press the Set
Level 8 - 135 Set push
Level 9 - 150 push Set
Level 10 - 165 Set push
Level 11 - 180 Set push
Level 12 - 195 Set push
Level 13 - 210 Set push
Level 14 - 225 Set push
When you do the changes necessary to reset the system.
Post has been editedneo-dj - 07.05.17, 11:30Reason for editing: In the header