ZyXEL / Keenetic Ultra II - Discussion | [wifirouter]



Rep: (3399)
ZyXEL Keenetic Ultra II- Discussion
ZyXEL Keenetic Ultra - Discussion
Attached Image
Information
Description
  • Product Name: Keenetic Ultra II
  • Part Number: EMG2885-T20A
  • NDM HW ID: ku_rd
  • Ultra Performance
  • Any tariffs up to 1000 Mbps
  • Automatic distribution of clients between 2.4 and 5 GHz bands
  • Four power amplifiers and 5 dBi antennas of special design for better coverage
  • Dynamic selection of the optimal Wi-Fi radio channel
  • 8 Gigabit Ethernet ports for computers, network drives, set-top boxes and TVs
  • USB 3.0 and 2.0 ports for disks, printers and 3G / 4G / DSL modems
  • File server up to 100 MB / s, torrent client, DLNA / UPnP AV
  • IPTV and Smart-TV support
  • Protection of Yandex.DNS and SkyDNS
  • Automatic prioritization of IntelliQoS traffic
  • Setup and control via mobileattachment
Additional photo
Specifications
Main characteristics

The processor - MediaTek MT7621AT (MIPS1004Kc) 2x 880MHz
RAM - 256 MB (DDR3)
Flash memory - 128 MB (NAND)
Wi-Fi 2.4 + 5 GHz - Yes
Wifi Class - MediaTek MT7602E 2T2R / 300Mbps (2.4GHz) + MediaTek MT7612E 2T2R / 867Mbps (5GHz) - AC1200
Antennas - 4x 5dBi (fixed ext)
Ethernet Ports - Realtek RTL8370M 8x GbE

Wi-Fi / WPS button вњ”
FN button - Yes, two buttons
USB Ports - 1 x USB 2.0, 1 x USB 3.0
3G / 4G connectivity Via compatible USB modem
Connect via DSL ADSL2 + / VDSL2 viaKeenetic Plus DSL
Telephony support -C Keenetic Plus DECT
Modes of access point, amplifier, adapter - вњ”

Performance

2.4 GHz Wi-Fi network speed - 300 Mbps
5 GHz Wi-Fi network speed - 867 Mbps
Gigabit home network вњ”
For tariffs above 100 Mbit / s вњ”
IPoE / PPPoE Routing - Up to 1800 Mbps Duplex
Routing L2TP / PPTP -Up to 800 Mbps
Reading from a USB disk - 90 MB / s (USB 3.0)

Functions and protocols

IPoE вњ”
PPPoE вњ”
PPTP вњ”
L2TP вњ”
802.1x
CABiNET вњ”
Multiple PPP Tunnels вњ”
PAP / CHAP / MS-CHAP / MS-CHAP v2 вњ”
MPPE (Auto / 40/56/128)
VLAN IEEE 802.1Q вњ”
Route Table (DHCP / Manual) вњ”
Link Duo вњ”
IntelliQoS вњ”
DHCP (client / server) вњ”
IPv6 Dual Stack вњ”
NAT вњ”
Igmp вњ”
UPnP
Manual port forwarding вњ”
PPTP / L2TP Transit вњ”
SPI DoS Attack Firewall вњ”
Ping checker вњ”

Wi-Fi wireless network

WEP / WPA-PSK / WPA2-PSK Network Protection вњ”
Support for additional guest Wi-Fi network вњ”
MAC access control вњ”
WPS Quick Setup вњ”
Wi-Fi Multimedia (WMM)

Applications

Mobile application for Android and iOS вњ”
Transmission torrent client вњ”
File server вњ”
DLNA server вњ”
UDP to HTTP proxy вњ”
FTP server вњ”
Print server вњ”
IPSec VPN Client / Server вњ”
PPTP VPN server - 10 tunnels
Internet filter Yandex.DNS вњ”
Parental control SkyDNS вњ”
Dynamic DNS client вњ”

Physical characteristics and environmental conditions

Device dimensions without antenna, W x D x H - 186mm x 121mm x 36mm
Mass device - 310g
Operating temperature range - 0-40 В° РЎ
Humidity of the ambient air during operation - 20–95%
Power supply - 100–240 V 50/60 Hz

Diagnostics and control

Web configurator in Russian вњ”
Command Line (CLI) by TELNET
The ability to control from the external network вњ”
Backup and restore configuration вњ”
Software update features вњ”
Logging system events вњ”

Equipment

Device
Power adapter вњ”
Ethernet cable вњ”
Instructions for use вњ”
Certificates
Documentation
Attached fileInstructions for use Ultra II.pdf(2.03 MB)

Attached fileSpecifications Ultra II.pdf(862.08 KB)

Attached fileHandbook of CLI Ultra II Command Interface dated 12/21/2018. Pdf(4.32 MB)

Updated, current version of the CLI Ultra II Command Interface Reference - cli_manual_ku_rd.pdf
Reviews, links
Useful information
Problem solving, setup
NDMS V2 + Entware
Keenopt setup
OpenVPN setup
[Entware] Raise OpenVPN server
[Entware] Openvpn client on the router
Enable 802.11n standard on NDMSv2 firmware (via CLI TELNET)
Forced assignment of N mode (compatibility N) for Wi-Fi via CLI from enpa
Wordpress on Entware
How to print from phone to printer via Android OS
Antenna Comfast CF-ANT2410DA for a place native to Keenetic II, Giga II
Flash modem in HiLink for maximum speed
CAT5 HiLink Speed ​​Test
All about IP Cloud (KeenDNS)
"White" IP from Rostelecom using Entware
Wake on Lan (WOL) function in ZyXEL Keenetic routers
A bit of theory on the mechanism of updating NDMSv2 firmware from _Danila_Master_
Yandex disk / WebDAV in ZyXEL Keenetic
Wi-Fi signal attenuation coefficients when passing through various environments
How to change the network name of the smartphone in Android?
EaseUS Partition Master Free is a handy program for partitioning a hard disk into partitions (suitable for creating a partition in ext3, creating two ntfs & ext3 partitions).
What type of file system and paging file is best to use? Enpa description
What type of file system and paging file is best to use? Option from miltt
Correction of the Transmission operation without reinstalling the router firmware from enpa
How to determine the type of antenna connector (SMA / RP-SMA)?
NTP SERVERS - time servers
Using the zram paging file (LZO) for the swap location from enpa
Creating an ISP (Internet Service Provider) interface via CLI (command line) from enpa
Lock site by name on the firmware from dezhik
If you need port 5 to distribute the Internet to devices on the wire from enpa
Speed ​​limit via CLI (command line) from enpa
PuTTY is a client program for working with network protocols SSH, Telnet, SCP, SFTP, for connecting via a COM port and ZModem, a utility for generating RSA and DSA digital SSH keys.
Solving the problem with ping in games specifically WOT for Wi-Fi from freealbert
WPS on a router - what it is and how to use it
Setting up a connection to a working VPN server using a "gray IP" at the provider from YEDkii
Forced assignment of speed on the port of the router through the CLI from enpa
Resetting factory settings (factory-reset) via CLI from enpa
2 ways to change the MAC address of a computer network card
Zyxel Keenetic Giga III + Zyxel Keenetic Plus DECT - Internet and telephony in the office from WOOF11
The impact of USB 3.0 devices on the quality of data transmission over the air
ОњTorrent client setup
Zyxel GIGA III router: setting up simultaneous work with several Internet channels from Sergei Golubitskiy (youtube video instruction)
Extending your home Wi-Fi network with Dalex-NEMAN ZyXEL PLA4201v2 EE powerline adapters
We fix the display of interfaces in the Connections section of enpa
Installing Keenetic Giga III in a private house from olezel
Setting up remote access Transmission from enpa
Setting up and installing minidlna (1.1.6 + git-8a996b-1) opag-package from enpa
Configuring and installing the syslog-ng opkg-package for recording logs to external media from enpa
Firmware update using enpa CLI TELNET command line
Turning off the LEDs of the router using the CLA TELNET command line from enpa
Disabling the FN button LED using the enpa CLI TELNET command line
When adding a torrent, you can choose which files to download?
Solving display problems \ login by domain name (hostname) of Keenetic router in Windows 10 from enpa
Using the WAN port as a LAN port in Keenetic Giga III \ Ultra II using the enpa CLI TELNET command line
Changing a Wi-Fi wireless channel in Keenetic using the enpa CLI TELNET command line
Configure automatic reboot using CLI TELNET by _Danila_Master_
Comments on the work of the Padavana TX Burst
Four Stream - Does the KN-1010 HT processor software support? Information from balian007
Installing and configuring Transmission 2.93 from Opkg Entware-3x for Keenetic Giga KN-1010 from enpa
Warranty information for Keenetic routers from 9119
Mini report on the implementation of the work Keenetic Ultra II from Ritter
Installing and configuring ntfs-3g-utils from Opkg Entware for Keenetic from enpa
Setting push notifications and alerts from Keenetic router from enpa
Routing networks through Wireguard Minutes enpa
TTL lock
Restore ZyXEL Keenetic
Instructions

Internet connection setup:

Install and configure KeeneticOS:

Reset:

Diagnostics:

Recovery firmware:

Reservation

Speed ​​Limit:

Remote access:

VLAN:

Forwarding and port configuration:

Wi-Fi setup:

WPS (Wi-Fi Protected Setup):

Security and DNS:

schedule :

Tunnels: PPTP, L2TP \ IPSec, IPSec, SSTP, OpenVPN, VPN server:

File server and USB-drives:

FTP server:

BitTorrent Transmission Client:

DLNA:

Digital television:

USB printer:

CLI (command line), SSH:

Modes:

3G / 4G modems:

Digital telephony:

OPKG packages:

IntelliQoS:
Internet speed testing
http://www.speedtest.net/ru/
https://www.nperf.com/ru/
https://2ip.ru/speed/

Attention! Testing servers are provided by external providers and the results of such tests depend on many technical factors.

Test results from these services can only be used for diagnostic purposes.
Application to manage the router
Transmission Management Application
Firmware


The official version of KeeneticOS
2.08

2.09

2.10

2.11

2.12

2.13

2.14

2.15

3.00

3.01
Debug version of KeeneticOS
Debug - test (draft) release of the operating system. Repeats the functionality that is in the officially released versions of "Release" or "Beta", but also contains additional fixes and new features. The debug version is under development and may contain bugs.

  • Testing debug versions of KeeneticOS is carried out on the forum Keenetic -here.
  • Changelog of debug versions of KeeneticOS -here.
  • Binary files debug versions KeeneticOS, can be downloaded in Files Keenetic -hereandhere
The program for recovering ZyXEL Keenetic Ultra II firmware.
KeeneticOS firmware catalog

The curator of the topic is enpa


Post has been editedenpa - 07.11.19, 19:11
Reason for editing: routing networks through Wireguard Minutes enpa



Rep: (184)
* nonstop1977,
Not sure dlna can run on 2 discs at once in the same place it is necessary to select a folder. One can.
Are you sure that other devices see them precisely dlna rather than Samba / FTP / ...


I checked. At 2.10, you can choose a lot of folders, but on the old mine still has one ... check.

Post has been editedaBlazer1991 - 25.06.17, 17:20



Rep: (0)
Yes DLNA for two disks are seen, with 2.07 is possible. 100% sure that TVs and other receivers see them precisely dlna, but the receiver on Enigma 2 for cifs sees the drives but only reason alone, although the settings entered for the two.



Rep: (0)
Guys please help, 3 weeks suffer. Keenetic ultra usb 2 does not see at all, for no apparent reason stopped seeing. flashing does not help. Can someone advise something sensible. He sees neither stick nor modems, personal



Rep: (0)
show logs when connected ...
You can still write on profile Support Forum



Rep: (0)
I can not connect to the router via Wi-Fi laptop with 802.11 g standard speed of 54 Mb / s, the router in Vidin podkl.ustr list. , 2.4 Hz exposed mode b, g, n. Or modem is too new for an old nouta through whistle works fine, but the built-in adapter does not want to see the Ultra 2, neighboring modems from Beltelecom sees.



Rep: (0)
Good day. Faced with this question. the answer to which is not found on the Internet. I hope you will help to clarify or clear the next question. Our organization uses a router ZyXEL Keenetic Ultra 2 with the latest firmware version 2.08 (AAUX.0) C2. About 100 employees are connected via a multi-channel unmanaged network switch to the router. Most users will want to block access to the Internet at the router level (since other management capabilities do not yet have). A problem is that in order to accomplish this you need to see the router: Home network - devices - to register a new device, give it a name, disable or enable access to the Internet and apply registration. That's only after 64 registrations router has ceased to register new devices with the issuance of the following error message:


host limit exceeded, the maximum of 64 hosts reached. 9175045
host "00: 11: 00: 30: f1: 22" is unregistered. 19007441

I have your answer to these questions:
- Is it possible on the device in any way increase the number of registrations more than 64?
- If yes then can send detailed instructions or a link to how to do it.

Contact the sluzhzhbu support Keenetis and that's what I said, the Internet - a series of centers Keenetic positioned as equipment for home use, the recommended number of clients connected to the router - 10-15.
The number of IP-addresses that can be configured as a constant through the router is 64 entries. This option to change is not planned.
To implement the connection of such a large number of clients is recommended to use multiple devices.

But I think there should be an opportunity to expand the number of permanent registration at the program level. It can not be so that the devices can add and register (to name and permissions) can not be.



Rep: (25)
Alex_K2366 @ 20.07.17, 11:33*
Now a new version of the internet 2.09 (release) is available.
Who put, there are improvements, please unsubscribe.

Why do you need to rely on someone's subjective experience, the knowledgewhat changed.



Rep: (0)
Hello!
Help me to understand.
I have a TV without a smart TV.
Will I be able to watch movies, pictures from the hard drive connected to the router?



Rep: (1091)
* Diamand77 If your TV supports the DLNA, yes. Check out this possibility.



Rep: (0)
Unfortunately not.



Rep: (1091)
Stable firmware version2.09.C.0.0-1 on 20/07/2017for Ultra II


Component kit
* USB modems Components, USB storage and Opkg - models with USB except Keenetic Omni, Omni II

* USB modems Components, USB storage - the models Keenetic 4G III rev.B, rev.A

* Recommended set of components - the models Keenetic Omni, Omni II


Base system:

Quick Setup NetFriend - Installed
USB Interface - Installed
Dynamic DNS Service (DDNS) Client - Installed
Network Accelerator - Installed
DHCP Server - Installed
Service IGMP / PPPoE proxy - Installed
UPnP Service - Installed
Wi-Fi Interface - Installed

Modes:

Client Mode Wi-Fi - Installed
Wi-Fi AP Mode - Installed
Wi-Fi amplifier mode - Installed

Networking:

Keenetic Plus DECT - telephone base station - Not installed
Application Level Gateway (ALG) for H.323 - Installed
Capture Network Packages - Installed
PPTP Client - Installed
IPv6 - Not Installed
GRE Tunnels - Installed
Application Level Gateway (ALG) for SIP - Installed
Traffic Classification and IntelliQoS Service - Not Installed
L2TP Client - Installed
SNMP Server - Not Installed
Application Level Gateway (ALG) for FTP - Installed
Application Level Gateway (ALG) for PPTP / GRE - Installed
IP tunnels IP - Installed
Application Level Gateway (ALG) for RTSP - Installed
Authorization provider CABiNET - Installed
Internet speed limit for clients (Shaper traffic) - Installed
PPPoE Client - Installed
802.1X Client - Installed
EoIP Tunnels - Installed

Applications:

Internet filter and parental control SkyDNS - Installed
PPTP VPN Server - Installed
BitTorrent Client Transmission - Installed
UDP-HTTP Proxy (udpxy) - Not Installed
File Sharing (Apple File Protocol and Time Machine) - Not Installed
DLNA Server - Installed
FTP Server - Installed
Remote Control via Cloud and KeenDNS - Installed
Internet filter Yandex.DNS - Installed
Checking the status of the Internet connection (Ping Check) - Installed
IPsec VPN - Installed
File and Printer Sharing (SMB / CIFS) - Installed

USB modems:

3G / 4G CDC Ethernet USB Modems - Installed
Keenetic Plus DSL - USB Modem ADSL2 + / VDSL2 - Not Installed
3G / 4G NDIS USB Modems - Installed
USB modems for dial-up phone lines - Installed
Samsung CMC-730 WiMAX USB Modem - Installed
3G / 4G USB Modems - Installed

USB storage:

File System HFS + - Installed
FAT32 File System - Installed
File System NTFS - Installed
Folder Access Control - Installed
USB Drive Support - Installed

Opkg:

Kernel Modules for USB Audio Support - Installed
USB over IP kernel subsystem modules - Installed
Kernel Modules for USB Video Support - Installed
Kernel modules for file system support - Installed
Kernel modules of the Traffic Control subsystem - Installed
Netfilter Subsystem Kernel Modules - Installed
Open Package Support - Installed
Nettable's Xtables-addons Expansion Pack - Installed
Kernel Modules for USB Support for DVB Tuners - Installed

Changes
Version 2.09.C.0.0-0 (official release *):

Wi-Fi: it neutralized the problem with the disappearance of the 5 GHz network (reported @ b3er)
Wi-Fi: rt539x (Keenetic II, Giga II, Ultra, Extra): added check for someone else's DA in the DISASSOC frame - Apple iOS bug bug with false deassociation
Wi-Fi: mt7612 (Giga III, Ultra II, Air, Extra II): fixed STBC support for VHT20, VHT40; Added VHT40 boost for Huawei P9 / Honor 8 smartphones that do not work with VHT80 in Russia and the CIS
Wi-Fi: site-survey regression fixed (review of access points from the client) - not all TDs were displayed
Wi-Fi: Keenetic Ultra, 5GHz: fixed outside guest WISP access point and on devices with specific MAC addresses; Fixed management model TxRate on RATE_ALG_GRP with the relevant train tables for SS3
Wi-Fi: fixed problem of unstable connection of 2.4G-only clients when Band-Steering is on
Linux, tty module: fixed bug when working with E392 and similar USB modems on Keenetic III; fixed possible deadlock on SMP devices when closing tty (for example, pppd serial hang-up)
Ping-check: for CdcEthernet interfaces, added check for the actual connection to the operator via modem polling byHttp:Megafon M100-4; MTS 830FT; Beeline MF835F, MF823; Beeline MF90, MF90 +; Huawei E3272, E3351, etc .; ZTE MF825A
DLNA: fixed binding of an SSDP socket to an interface (reported by @enpa)
Transmission: fixed selection of download directory that caused tmpfs memory overflow after disconnecting USB drive
fixed PPP uptime reset after disconnect
DNS proxy memory leak fixed
improved DTMF recognition on Keenetic III
improved reset of current TCP / UDP sessions when Internet access is denied
reduced impact of the IntelliQoS shaper on priority traffic
updated OpenSSL to 1.0.2l

* Officially released for Keenetic Start II, Lite III rev.B, 4G III rev.B, Giga III, Ultra II, Air and Extra II.
Rebuilt in delta for Keenetic II, III, Giga II, Ultra, Lite II, Lite III, 4G III, Omni, Omni II, Viva, Extra, DSL, VOX and LTE.

Version 2.09.C.0.0-1:

Fixed reset config after reload restored Agent: http / ci (reported @Wizer)
(c)https://forum.keenetic.net/

Attached fileKeenetic Ultra II_2.09.C.0.0-1.zip(14 MB)

Mirror:
cloud.mail - v2.04, v2.05, v2.06, v2.07, v2.08, v2.09 Firmware Keenetic
yandex.disk - v2.04, v2.05, v2.06, v2.07, v2.08, v2.09 Firmware Keenetic
Picture


Post has been editedenpa - 24.07.17, 14:27



Rep: (1)
The dunes in this very good!



Rep: (66)
Someone know what is this Opkg and why they are needed
Kernel modules of the Traffic Control subsystem - Installed
Netfilter Subsystem Kernel Modules - Installed

?



Rep: (14)
Here and Now @ 26.07.17, 20:45*
What is this Opkg and why they are needed


forum.keenetic



Rep: (0)
any problems experienced with wifi after upgrading to 2.09?
I use only stable firmware. 2 days ago updated to the new firmware, the laptop (wifi intel 7260) began to fall off from vayf. However, other devices and laptop feel good. Tried to update the driver on the adapter, it is the connection drops. He fell back to 2.08.
Is there anyone else this problem?
P.S. there is no possibility to check the adapter if 2.08 will not fall off the Internet, the problem is not in the wifi card.



Rep: (0)
the same problem only with telecom gnusmas also Vayvay falls off, back to the previous firmware!



Rep: (0)
Incidentally helped off (Disable Internet access to all unregistered devices) as soon as the turn on the TV set immediately Net chopped off (!



Rep: (186)
Could not find any vebmorde nor My.Keenetic on Android, is it possible to choose which files to download from a torrent?



Rep: (24)
Peyote @ 11.08.17, 17:45*
Could not find any vebmorde nor My.Keenetic on Android, is it possible to choose which files to download from a torrent?

Yes you can
Here is an example.
Attached Image



Rep: (11)
And there is no information when will update the model in the style of Extra II?


Full version    

Help     rules

Time is now: 25/11/19, 15:04