0.
Question: What is the password for setting the clock via sms commands?
Answer: Currently known mass passwords are 123456 and 523681.
1.
Question: Why does the marker in the program show the location of the clock in different colors?
Answer: The color of the marker depends on how the clock is positioned:
Red - on GPS (satellites)Green - via Wi-Fi networks (if the clock is near the Wi-Fi point, even if the network is closed!)Blue - on LBS (cell towers, sooo inaccurate!)2.
Question: How to set the font for displaying entries in the address book in hours?
Answer: No The problem of small print can be solved only if the names of the entries are written in capital letters - MOM / DAD / BABA / DEDA, etc.
3.
Question: Which version of the program is better?
Answer: You decide that the functionality of all programs is the same, the only difference is in the appearance of the functional representation.
4.
Question: Can I use the program at the same time?
Answer: Try it, it was tested on 4.2.2 and CM12.1 - all three applications are installed and everything works fine. In the settings of all programs will be the same data that pulls from the servers. Changing something in one program, you will change the data in other programs.
5.
Question: How are the watches on the Wi-Fi network if the network is messed up?
Answer: The clock does not connect to Wi-Fi in the usual way (ologin / pass). Even if Wi-Fi is ruined, the clock is still positioned via Wi-Fi more or less accurately.
6.
Question: Why is the location of the clock in the program shown with an accuracy of 1.5-2km?
Answer: Most likely this error is due to the fact that the clock was found according to the cell towers (LBS). Disable this mode in hours through the program.
7.
Question: How to disable LBS mode in the program?
Answer: In the SeTracker and SeTracker2 programs, you need to go to the Reports and at the top move the switch to the right:
In SeTracker3, everything is easier - go to the settings, find the LBS item and move the switch to the off position by sliding the switch to the right:
8.
Question: How to specify the number of SOS numbers?
Answer: SOS numbers should be indicated in the international format:
1)
in Russia:+ 7РҐРҐРҐРҐРҐРҐРҐРҐРҐРҐ
8РҐРҐРҐРҐРҐРҐРҐРҐРҐРҐ (but this is not certain)
2)
in Ukraine:0XXXXXXXXX
+ 38XXXXXXXXX (but this is not accurate)
9.
Question: Indicated the number for monitoring (wiretapping) in the international format (in Russia + 7XXXXXXXXXX), but the clock does not ring the phone. What to do?
Answer: Correctly indicate the phone number in Russia 8РҐРҐРҐРҐРҐРҐРҐРҐРҐРҐ and nothing else.
In Ukraine, a monitoring number (wiretapping) is entered in the same way as SOS - 0XXXXXXXXX
10.
Question: When SeTracker swears "Please confirm the registration code correctly" when you enter the 10 - digit. What to do?
Answer: Send the clock via the sms command pw, PASSWORD, tt, # (instead of the PASSWORD, you must enter the password of the "access" to your watch. Currently known mass passwords are 123456 and 523681)
Get a 15-digit code in response and enter it into SeTracker
proof11.
Question: When trying to determine the position of the clock, the program gives "no network equipment" (not found on the network). What to do?
Answer: There may be several reasons.
0) the balance of the SIM card must be positive and with the available amount of Internet traffic!
All other reasons are considered based on the execution of p.0!
1) In order for the watch to be through SeTracker, the sim card must be with 2G! Not 3G / 4G, but with 2G! With this question you need to your PPSOS.
Be sure to ensure that after installing the sim card on the clock display shows the signal of the cellular network and the Internet icon "E".
If everything is fine with 2G, then it is necessary to check the correctness of the prescribed APN.
2) The APN (Access Point Name) provider is incorrectly registered. APN is set automatically, but in order to exclude this reason for the message “No network equipment (not found on the network)”, configure it to Send to the watch via sms command corresponding to the operator:
pw, PASSWORD, apn, internet, gdata, gdata # - Megaphone
pw, PASSWORD, apn, internet.beeline.ru, beeline, beeline # - Beeline
pw, PASSWORD, apn, internet.mts.ru, mts, mts # - MTS Russia
pw, PASSWORD, apn, Internet.tele2.ru, tele2, tele2 # - Tele 2
pw, PASSWORD, apn, internet, internet, # - Vodafone
pw, PASSWORD, apn, mts, mts, mts # - MTS Belarus
(instead of the PASSWORD, you must specify the numbers of the password "access" to your watch - see p. 0 FAQ)3) The server address, written in hours, does not match the address of the server SeTracker is accessing. This is probably the main cause of the “No network equipment (not found on the network)” problem. Do the following:
Send from the smartphone to the SIM card number in the watch the command for requesting the parameters: pw, PASSWORD, ts # (instead of the PASSWORD, enter the numbers of the password “access” to your watch - see p.0 FAQ) The clock must be included.
Wait for the response of a large message and look at the information about the server address in the “ip_url:” line, check which region it corresponds to, and indicate this region in the application. List of server matching regions:
Europe and Africa ip 52.28.132.157 (port 8001)
Asia and Oceania ip 54.169.10.136 (port 8001)
North America ip 54.153.6.9 (port 8001)
South America ip 54.207.93.14 (port 8001)
Hong Kong ip 58.96.181.173 (agpse.3g-elec.com) (port 8001)
Save the sms, just in case, for the possibility of rollback. If everything worked out, go to
>>> .
If it is not possible to register the clock in another region or the data in the “ip_url:” line is not suitable for any of the specified regions, then it is recommended to force the server address with the appropriate command. For example, for the Europe and Africa region: pw, PASSWORD, ip, 52.28.132.157,8001 #. This is the most common option. For other regions, substitute the appropriate ip.
>>> Send the pw, PASSWORD, reset # commands to the clock and wait for them to restart.
(instead of the PASSWORD, you must specify the numbers of the password "access" to your watch - see p. 0 FAQ) 12.
Question: What is the number of contacts can be recorded in the clock (notebook)?
Answer: 15