Discussion of devices not related to this topic is prohibited. If the theme you need for a specific model does not exist - create it.
Instead of saying “Thank you!” Use. If you have less than 15 posts - click on the button.under the message where they helped you, and write thanks.
Instructions for firmware Totolink N300RT(andRhandF1) (translation from forum.anphat.vn)
Firmware via WEB-muzzle
Determine the model of the device, the version and date of the current firmware:
ATWeb muzzledevice go to the "Management" ->"Upgrade Firmware".
The “Firmware Version” field will show the name of the current firmware.
The example above shows that the name of the firmware:TOTOLINK-F1-v1.0.0-B20140416. 1632
Decryption
Model Name -F1
The firmware version is1.0.0.
Date and time of firmware -16April2014, 16 hours 32 minutes . It is possible that you have a brick on your hands, and it is impossible to find out the required data in this way. Then we are guided by the data indicated on the sticker on the back or bottom of the device, download the firmware, which seems to us to be correct, and immediately go to step7
Knowing the model of the device, the version and date of the current firmware, you can downloadcorrect version of Just in case, save the firmware with a short path without spaces (for example, "C: \ Temp \ firmware_file_").
Before the firmware procedure, it is very desirable to make a backup and reset the settings:
"Management" ->"Save and Reload settings" ->"Save" button.
"Management" ->"Reset to default settings" ->save button
It does not hurt to take screenshots of the settings or write them on paper.
Firmware via WEB-muzzle: Do NOT use Wi-Fi connection to upgrade firmware!
Connect the router to the computer with a network cable (patchcord) using the LAN port (the first one, for example).
Open the WEB face of the router in the browser (by default -http://192.168.1.1).
Go to the "Management" ->"Upgrade Firmware".
Click the "Browse" button, specify the path to the firmware file and click the "Open" button.
Just in case, check the firmware version and the path to the file again, then click the "Upload" button
Features
If the current firmware, due to its peculiarities, does not allow updating the device through the WEB face, go to stepF.
The firmware update process takes about 2 minutes.
After a successful update, the router will automatically reboot.
Just in case, do a reset - press and hold the reset button (WPS / RST - located on the side or bottom of the router) for 10 seconds, and then release.
After resetting, the router will need about 1-2 minutes to run.
IN CASE OF FAILURE OF POWER SUPPLY, A WRONG FILE OF THE FIRMWARE OR FROM HARMFUL ROUTER MAY WRAP! In this case, go to step] 7
Using WEB-muzzle reconfigure the router from scratch to print screens, records or from memory if possible. You can try to restore saved in step.3 configuration file. This completes the firmware upgrade process; the next steps are not needed.
Rebuilding a brick or updating an "un-upgraded" firmware: Everything that you do according to the following, you do on your own initiative, at your own risk! There is no guarantee that you will not kill your device completely!
Vietnamese comrades offer to use Windows 7 or XP and disable the firewall at the time of firmware.
From myself I will add that I was flashing under Windows 10 x64, but in any it would be desirable:
Disable firewall and anti-virus (including Windows Defender), if any.
Unpack applicationFrmUpg.exe in a place with a short path without spaces.
Pre-downloaded firmware, which you thought was "correct", put next to the application.
Run the application in compatibility mode Windows XP, if you have a version of Windows 7/8 / 8.1 / 10.
Run the application as Administrator.
If all preparatory steps have been taken, then:
Turn off Wi-Fi
Connect the network cable (patchcord) from the computer to the port of the routerLAN1 or LAN2
Set the computer’s TCP / IP LAN adapter properties ("Network connection") to a static addressIP 192.168.1.100 (mask 255.255.255.0)
Run the applicationFrmUpg.exe and set the following parameters:
Router IP:192.168.1.6 - manually.
Specify the firmware file:
Click on the "..." button.
Specify the file type "*. *".
Select the firmware file with the extension "* .web".
Do not change the other parameters ("VoIP Module File" and "Password" - empty, "Port" - 69, "TimeOut" - 5).
Power off the router
Hold the router reset button (WPS / RST) and do not let go!
Turn on the power of the router, wait about 10 seconds (the nature of the flashing LEDs of the router should change), and release the reset button.
Click "Send " in the application FrmUpg.exe . If successful, the firmware will start, which can last about 10 minutes. Turning off the power at this time is most likely fatal.
The firmware may end with an error message. This is not necessarily scary.
Set the TCP / IP properties of the computer's LAN adapter ("Network Connection") to automatically obtain an IP address
Reset the router - press and hold the reset button (WPS / RST) for 10 seconds, and then release
Firmware complete
Once again, all of the above in steps 6-17 can cause the router to wrinkle, everything you do - you do at your own peril and risk, and I am not responsible for any liability that you may incur as a result of using non-standard software.
There is no curator in the subject. For filling the caps, please contact the section moderators via the "Complaint" button under the messages to which you want to add links.
Faced with the fact that he could not properly update the firmware. Trying to sew through TFTP, I almost ruined the device. In the end, I found the Vietnamese forum and successfully used the solution from this forum. Decided to share - translated and adapted.
The router is not deservedly deprived of attention. In fact, the router is quite intelligent and pleasant. Of the inexpensive ones, it is clearly better than cheap tipi-dy-links. : good:
Guys good day. There is a Chinese N311RT died SPI flash drive. Is anyone looking for DUM? If I understand correctly, the glands of the 300 series and 311 are very similar in principle to the RTL8196E chip
N300Rt does not want to boot. I dumped a dump from a known working router, I flashed my own, but still the same picture, when turned on, all indicators except Sys and wi-fi light up. When trying to upload firmware through a miracle utility, after clicking Send, the strip runs through, while the port indicator is actively blinking, but then an error pops up at the end of the second strip. What could be? Ports coming out live. Think RAM is possible? Who has any ideas?
the current that I bought this miracle, I immediately asked for firmware TOTOLINK-N300RT-V2.1.3-B20160128.1711 WiFi gives out exactly 100kb / s, I don’t know how it worked on firmware from the store where in the settings is there any bandwidth limit? Where? I like the entire menu I didn’t find anything like it
I have a router from the provider I can go to the admin panel, but I can’t update through it: "Invalid upgrade file!". I tried V2.1.3-B20160128 and V2.1.6_20160516. The router has TOTOLINK-N300RT-V1.0.0-B20150304.1558 installed.
It also doesn’t work through FrmUpg - "error - request timed out! Transmission is interrupted! Message - for normal router operation, restart it."
No other provider except the former, of course, does not plow on this router! How to reflash it?
I can go to the admin panel, but I can’t update through it: "Invalid upgrade file!". I tried V2.1.3-B20160128 and V2.1.6_20160516. The router has TOTOLINK-N300RT-V1.0.0-B20150304.1558 installed.
It also doesn’t work through FrmUpg - "error - request timed out! Transmission is interrupted! Message - for normal router operation, restart it."
No other provider except the former, of course, does not plow on this router! How to reflash it?