[X]Assistant

[Gam099]

Nomi C10103 Ultra + 10 - Firmware
Nomi C10103 Ultra + 10 ″ 3G 16GB
Description | Purchase пїЅ | Firmware пїЅ

Drivers and Utilities

Flash driver, drivers and working firmware for C10103 Ultra SC141 K03B rev 1.0
Universal adb driver

Firmware

S102A_L_NONE_RY_NomiC10103_KR_161101_V1.3

Backup infinity for the board S108-7731-D (162) V1.0.
Expert_Q10_RPZ300010001-RPZ300014150_V1.1.

not relevant

C10103 firmware SC141
At the moment, users are faced with the inoperability of this firmware.
The link to the firmware is left in the topic header, as a landmark. Users are still looking for a working version.

Instructions

Instructions on firmware Nomi C10103 without + with working links
Instructions on firmware
With a sensor mirroring issue on the Nomi C10103 Ultra 1Gb RAM, 8Gb ROM,

miscellanea

Tablet info
//savagemessiahzine.com/forum/d…016-10-29-12-12-13.png
Everything you need for the firmware is in one archive
Everything you need for the firmware is in one archive
For those who connect OTG flash drives and Hard disk, the tablet does not support the NTFS file system format

Screenshots

There is no curator in the subject. For filling caps, please contactmoderatorssection through a buttonunder the messages to which you want to add links.

Post has been editedsnekt - 05.02.19, 22:26

Reason for editing: Nomi C10103 Firmware Manual without + with working links

[Voidup]

Vaalf @ 10/31/2016, 1:31 PM

* Gam099, if you do not mind, try the instructions to translate into Russian and put a separate post.

Brief instructions from yourself:

Instructions on firmware

1) We charge the device not less than 30%.
2) Go to the folder with the drivers and install the appropriate (x86 or x64) based on the installed system. Tested on XP x86 \ Win7 X64
* Note: on Win 7 and higher, a window with an unchecked driver signature may pop up - we agree and install. Installation time, approximately 1-3 minutes.
3) Open the program for the firmware "UPGRADEDOWNLOAD_R2.9.9015".
4) Select the file for the firmware with the extension "PAC". See the screenshot below.

5) Check the name of the firmware and click to start the firmware. See the screenshot below.

6) Turn offdevice completely.
7) Connect our device for firmware. To do this, hold down the volume button "+" and connect the usb cable. If the drivers are installed correctly, the program should display a line with the current state of the firmware. 3-5 minutes flashing time
* Note: If the process stops at the very beginning, then press the "Reset" button, after that the tablet will reboot and go to download. Then turn it off again, and repeat from step 6. The same process of the firmware may be terminated due to the cable \ connector on the tablet.

Post has been editedvaalf - 31.10.16, 17:46

Reason for editing: raised in the topic header

[Virbal]

Made according to the instructions, get out an error during the firmware _BKF_NV_W status: finish progress: failed. Please help with a solution

[Gam099]

Virbal,
Drivers are all worth it Try updating the program can help

[Virbal]

I am flashing the tablet Nomi c10103 ultra, because the system does not start. writes an error:
E: unknown volume for path [/ sdcard / rock / update]
E: unknown volume for path [/ sdcard1]
E: unknown volume for path [/ sdcard1]
Help solve the problem with a download error or firmware ...

I installed the drivers, but I'm not sure that they work. When connecting the device, there are no ADB interface drivers and 2 Spreadtrum

But, during the firmware, the drivers seem to be determined. but it is already a new error. flashed with SPD Flash Tools 4.0.1
port: 3 step: _BKF_PhaseCheck status: unplugged Progress:Failed: incompatible partition

Phasecheck
I found that in Backup you need to disable file backup: NV_W; PhaseCheck; ProdNV; Who will say something about this?

Post has been editedvaalf - 01.11.16, 12:35

[Gam099]

Virbal,
Here is adb driver universal try itadbdriver

Post has been editedvaalf - 01.11.16, 12:37

Reason for editing: raised in the topic header

[Virbal]

The drivers are installed, but the problem with the firmware remains ...
What happens if I turn it off in the backup file backup: NV_W; PhaseCheck; ProdNV; Who will say about this?

or about the problem itself when launching the tablet:
I am flashing the tablet Nomi c10103 ultra, because the system does not start. writes an error:
E: unknown volume for path [/ sdcard / rock / update]
E: unknown volume for path [/ sdcard1]
E: unknown volume for path [/ sdcard1]

[vaalf]

M

We move to subsection:Other brands

[Voidup]

Virbal,
Well, how are you doing? It turned out to flash or still a brick?

[renren]

I flashed it with the firmware from the Ultra + 16gb header, there is no image ((
MB who has a firmware of another version?

[Voidup]

renren @ 11/04/2016, 6:55 PM

I flashed it with the firmware from the Ultra + 16gb header, there is no image ((
MB who has a firmware of another version?

Write the full name of what firmware you sewed and what is your tablet.
In the header, the firmware is from the 8Gb version, although it may be suitable for 16Gb.
I was flashing Inomi Ultra 8Gb with this firmware and DEXPa firmware, everything worked. Although at one point, the tablet turned into a "brick" - the black screen also turned on, and with the firmware, the process ended with errors. It was possible to win after 3-4 days.

[sanek96]

People, I have a tablet Nomi C10103 Ultra. I came to the firmware, I can’t turn it on or off normally. The ever-blue screen with the inscription Nomi. When I tried to flash, I got an error, but now I do not react to anything ...

[CBETJIOMYP]

Good day, this creation is also on hand with the inability to load beyond the logo (the recovery also did not load). It was only possible to flash it by removing the checkmarks as Comrade wrote. Virbal (at your own risk, of course) As a result, there is no image, but judging by the sound of the keys, the OS is loaded. Stitched firmware from the cap. I also tried from a similar dex (ursa 210 seem). The result is identical.
Brick? Or is there a chance to revive?

Post has been editedCBETJIOMYP - 07.11.16, 15:33

[Tekilla-boom]

The same vaznya with the same plan, Nomi C10103 with firmware _BKF_NV_W status: finish progress: failed
Planche is determined, then no. Butlup stuck.
What to do xs.

[Tekilla-boom]

With the firmware SPD 4.0.1 I write this
This is when you uncheck the checkbox "I found that in Backup you need to disable file backup: NV_W; PhaseCheck; ProdNV;"
And the next screen was already in stock.
There is a suspicion of a memory dump.

Post has been editedvaalf - 19.11.16, 23:36

Reason for editing: Pictures under spoiler

[antifront]

New firmware came through the air Who will tell you what's new?

[renren]

In the header, the firmware for Nomi (C10103 Ultra 10 ″ 8GB White) but not for Nomi (C10103 Ultra + 10 ″ 3G 16GB Black). There is no firmware for this model on support.http: // nomi-electronic ... ltra-10-3g-16gb-black /

I do not recommend flashing to those who (Ultra + 10 ″ 3G 16GB Black) get a black screen.

[Voidup]

As I wrote earlier, I managed to restore my brick, very hard and long (3-4 days). There were errors: Operation Failed, Incompatible partition, BKF_NV, etc.
A little later I will do the instructions on how to do it.
True, I had a 8Gb version, but you can try at your own risk.

[energaiser2]

How to be to those who have already flashed version 16gb, version 8gb?

[Fly442Miracle5800]

What version of android in the cap?

[Fly442Miracle5800]

It was done just to glow, how can I return to my native firmware now?