11 pagesV  « < 9 10 11 »  
 
REPLY
> FZCAM V380, FZCAM R1 and FZCAM R2 - Discussion | [ip camera] ip camera talk
ivanvias
Message#1
22.07.16, 17:38
Guru
*********
[offline]

Group: Friendssavagemessiahzine.com
Messages 2482
Check in: 05.01.07

Reputation:-  104  +

FZCAM R2 - Discussion

A photo:
Attached Image
Attached Image
Description:
  • WIFI IP camera with night view
  • Support Plug & Play (P2P), no need for DDNS, no need for port mapping.
  • Simple management and setup, through the application on the phone. Supports iOS, Android operating systems.
  • Support ONVIF protocol
  • MicroSD support (MicroSD card file system, must be in FAT32 format),
  • Support remote playback. (Note: 32GB SD card lasts approximately 3 weeks).
  • Alarm: The ability to send a message about the movement to the phone using the installed application, does not send screenshots to the mail, but the camera resets the screenshots of the alarm to your cloud, you can watch from the application)
  • There is a microphone and speaker. Using the application installed on the phone, you can voice a message that is transmitted through the built-in speaker in the camera.

Specifications:
Attached Image
Useful links:
Windows program
https: //onedrive.live...7B%21112&action=locate
The service nvdvr.net on port 5050 (cloud) is used. MVCMS connects either directly or via the cloud at 00000000.nvdvr.net:5050 (where zeros is the camera ID) Name and password is required, port forwarding is also needed to access from outside
Video writes fine, loses without crutches in any player. On the smartphone, you can view through the application, on the PC you can watch and download. The application itself in the market is called v380.

You can play with the camera seller 31101562 admin 3154
Data from media info on video
General
Complete name: C: \ Users \ admin \ Desktop \ RecFiles \ Rec1_20160718115221_A_1.avi
Format: AVI
Format / Info: Audio Video Interleave
File size: 10.1 MiB
Duration: 1mn 57s
Overall bit rate: 725 Kbps

Video
ID: 0
Format: x264
Codec ID: x264
Duration: 1mn 57s
Bit rate: 685 Kbps
Width: 1 280 pixels
Height: 720 pixels
Display aspect ratio: 16: 9
Frame rate: 25.000 fps
Bits / (Pixel * Frame): 0.030
Stream size: 9.56 MiB (94%)

Audio
ID: 1
Format: ADPCM
Codec ID: 11
Codec ID / Hint: Intel
Duration: 1mn 56s
Bit rate mode: Constant
Bit rate: 32.4 Kbps
Channel (s): 1 channel
Sampling rate: 8,000 Hz
Bit depth: 4 bits
Stream size: 462 KiB (4%)
Interleave, duration: 63 ms (1.59 video frames)


How to connect from scratch?
View RTSP stream
MVCMS_Lite - view video from PC
New PC software



  • Before posting read the message Video section rules
  • Messages that are not related to the topic of discussion (offtopic) are deleted without warning.

There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonPictureunder the messages to which you want to add links.

Post has been editedmihadom - 31.01.19, 10:05
Reason for editing: New PC software
deniska817
Message#202
12.02.19, 12:48
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 333
Check in: 28.02.15

Reputation:-  20  +

* Spa_m, connects without problems, but there is no image (black screen). Video takes, screenshots do (but what shoots can be found only after viewing).
ivanvias
Message#203
13.02.19, 07:13
Guru
*********
[offline]

Group: Friendssavagemessiahzine.com
Messages 2482
Check in: 05.01.07

Reputation:-  104  +

Try to look through vpn. Maybe the wire is blocking.


--------------------
hp ipaq 2490b, RoverPad 3w G70 4Gb, Samsung witu i900 16gb, LG Optimus One, Jiayu G2, Star N920e
Spa_m
Message#204
20.02.19, 15:59
Old resident
*******
[offline]

Group: Friendssavagemessiahzine.com
Messages 734
Check in: 17.03.10

Reputation:-  30  +

In general, the new program for the PC, although it began to show, works extremely unstable with me. It shows, it does not connect, it shows with big brakes, while the phone in the same place works without problems with the camera. Does everyone have it?


--------------------
MCU-4.3.1.2-7-10-6501 / system - 2.7.22 / dvd - 2.13.13-860mc
___________________________
MCU - 4.3.10.1-30-10-650101 / System - 2.8.6 / DVD - 2.13.13-1200xh
gipakozold
Message#205
21.02.19, 22:04
Visitor
**
[offline]

Group: Active users
Messages 25
Check in: 13.03.08

Reputation:-  0  +

Tell me, and no one has problems viewing cameras from the network,
that I have such a suspicion that in connection with the frequent blocking in our country, something is locked up, which affected the operation of cameras via ctnm (p2p)
Camera v380 S1
ivanvias
Message#206
22.02.19, 09:17
Guru
*********
[offline]

Group: Friendssavagemessiahzine.com
Messages 2482
Check in: 05.01.07

Reputation:-  104  +

* gipakozoldseems to work fine. It is necessary to look in more detail. Provider through which the camera works. The provider through which you want to connect to the camera. Router.


--------------------
hp ipaq 2490b, RoverPad 3w G70 4Gb, Samsung witu i900 16gb, LG Optimus One, Jiayu G2, Star N920e
gipakozold
Message#207
24.02.19, 01:04
Visitor
**
[offline]

Group: Active users
Messages 25
Check in: 13.03.08

Reputation:-  0  +

How to diagnose what is the matter - how to find out that the provider is to blame, do not wrap the camera in VPN somewhere in China or somewhere else ..
ivanvias
Message#208
24.02.19, 10:48
Guru
*********
[offline]

Group: Friendssavagemessiahzine.com
Messages 2482
Check in: 05.01.07

Reputation:-  104  +

* gipakozold, 1. Inside your network connects normally ?. 2 check how to connect through different provov, for example from a mobile. 3 check how to connect there is run vpn (download from google play)


--------------------
hp ipaq 2490b, RoverPad 3w G70 4Gb, Samsung witu i900 16gb, LG Optimus One, Jiayu G2, Star N920e
taran11
Message#209
28.02.19, 16:18
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 270
Check in: 15.05.10
Samsung Galaxy S8 Exynos

Reputation:-  44  +

In addition to the patch I previously laid out, there is a bit modified.
Solves the problem of access via telnet.
Access from root appears. No password needed.
The firmware mechanism is the same:
We unpack the archive on an SD card formatted in FAT32.
We insert the SD card into the camera.
Camera reboot / turn on.
Next, the camera itself is sewn a few seconds. and, attention, it reboots itself into working mode.

At this stage, the open telnet port (23) appears. You can log in and do anything.

Rtsp might not work at the moment. But it will work steadily after the next reboot.

Additional Information.
Upon completion of the patch, the file log is written to the root of the SD card. While this file is there, and nothing has been deleted from the card, the firmware will not be produced when the camera is rebooted / turned on.
After the 2nd reboot, telnet falls off but rtsp stably appears.
If you need telnet again, delete the log file from the card, when you restart, the patch works again. Telnet appears, rtmp falls off.
Next reboot: telnet closes, rtsp opens.
An FTP daemon is built into the firmware. Run by the command:
tcpsvd -vE 0.0.0.0 21 ftpd -w / &

After running ftpd, rtsp miraculously starts working, while telnet doesn't fall off. But all this happiness lasts only until the device is rebooted.

Everything would be fine, but there was a natural idea to fix the start-up ftpd in autorun. Modifying one of the files, uploading it back to the camera via FTP. Restart.Brick.
Everything. No firmware from previously laid out in the subject are not sewn.
I note that a similar embarrassment occurred with another dude from the foreign forum, from which I actually took this patch. He also changed in some kind of conf. Debug file from 0 to 1. And he also got a brick.
I do not post the patch yet.
I also accept tips on how to try to revive my camera.
Maybe someone else has a firmware (archive of their own), that one could try to flash.
There are 3 pins RX, TX, and GND on the board. I assume that these may be exits to the debugging terminal. But so far no reliable information on this issue has been found.

I would be grateful advice.

Post has been editedtaran11 - 28.02.19, 16:50
den.lenin
Message#210
28.02.19, 16:24
a guest
*
[offline]

Group: Users
Messages 2
Check in: 18.07.07
Glofiish (E-Ten) X500

Reputation:-  0  +

taran11 @ 02.28.19, 19:18*
In addition to the patch I previously laid out, there is a bit modified.

link please?
Wins83
Message#211
06.04.19, 16:12
Novice
***
[offline]

Group: Active users
Messages 32
Check in: 11.04.09
Apple iPhone 5s

Reputation:-  5  +

Hello everyone, became the "happy" owner of such a camera
Here's a dump for those who want to restore their bricks

Attached files

Attached filewin25q64jvs10_my_dump_reset.rar(6.52 MB)
Wins83
Message#212
06.04.19, 18:04
Novice
***
[offline]

Group: Active users
Messages 32
Check in: 11.04.09
Apple iPhone 5s

Reputation:-  5  +

taran11 @ 04/06/19 17:52*
And how to cut it into a brick, tell me, please.


any programmer that supports 25xx
on Ali from 150r
I do not see any other option yet
Wins83
Message#213
07.04.19, 14:08
Novice
***
[offline]

Group: Active users
Messages 32
Check in: 11.04.09
Apple iPhone 5s

Reputation:-  5  +

If possible in more detail. It is required to solder the mikruhu from the device or the programmer to solder enough on your feet. What then legs, what mikruha ... what program ...



program and programmer is called CH341A
Open Ali in the search type CH341A
take the programmer and clothespin approximately 350r (it is possible and cheaper to find)

open the camera remove the lens and hang the clothespin on the 8th and winbond 25q64xxx chip (the last letters may be different)
you do not need to draw out anything when using a clothespin or to remove a microcircuit and put it on an adapter if you take only the programmer for 148p, but it is more convenient for me with a clothespin
open the program, select 25xx and click on define the chip; if everything is successful, the program will show the model (25Q65b for example)
sure! read your dump and save
then open the file ..... and sew anything

in the presence of bricks in Voronezh can help flash
taran11
Message#214
08.04.19, 12:18
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 270
Check in: 15.05.10
Samsung Galaxy S8 Exynos

Reputation:-  44  +

Wins83 @ 04/06/19 15:12*
Here's a dump for those who want to restore their bricks

Attached files

win25q64jvs10_my_dump_reset.rar (6.52 MB)


Huge respect.
The device is restored.
Also found a working mechanism to enable FTP and Telnet on an ongoing basis.

To do this, you must modify the file vg_boot.sh located on the path / mnt / mtd
add 2 lines to the end of the file:
telnetd -l / bin / sh &
tcpsvd -vE 0.0.0.0 21 ftpd -w / &

IMPORTANT!
Editing a file must be done by an editor that can save files in the "xNIX" format, (without an extra newline character or a carriage return at the end of lines). In Windows, I do not know these. Under debian mcedit, nano, vi.
I launched MC under debian, connected to the camera via FTP. Downloaded vg_boot.sh to a local folder. Edited by editor nano, and uploaded via FTP back to the camera.
In the attachment, the corrected file, if anyone needs it.
I strongly recommend to compare the contents of my and your file before overwriting.

I do not get tired of repeating everything that you do - you do at your own peril and risk.And you have a chance to get a brick by the result (as it happened with me earlier), and it is possible to keep from this state only by flashing the programmer.


The question remains how to log in to FTP and Telnet. I do not have a special need because there is no one in my network except me. But for the completeness of the solution, it seems it would not be bad to bring the matter to mind.
Preliminary analysis showed that the / etc / passwd file is not writable. Modify it will only firmware.

Tips are accepted on this.

Attached files

Attached filevg_boot.zip(381 bytes)


Post has been editedtaran11 - 09.04.19, 17:14

11 pagesV  « < 9 10 11 » 


 mobile version    Now: 02.05.19, 04:56