Hackintosh on PC - macOS Sierra 10.12 | [macOS] Installation, discussion, sharing experiences



Rep: (1778)
macOS Sierra 10.12


Attached Image

Install macOS Sierra
Installation only for the brave, who is not afraid to lose the Old!
macOS Sierra 10.12 (16A201w) Developer Preview

Useful links:
Links to images:

When installing macOS, the presence of keys -v debug = 0x100 keepsyms = 1 is mandatory !!!

K


Post has been editedctich - 18.07.19, 09:19



Rep: (0)
H work now. Far from Peter. When choosing the installation in Clover, writes "this version of mac os x is not supported"

Posted 03/20/2019 01:25:

From PC *



Rep: (597)
* laccursedl
and what system set? on your hardware i5-7600 minimum, if I'm not mistaken on 10.12.4, I would try with 10.13.6



Rep: (0)
It is put 10.13.1. I tried to fill in 10.13.6, Clover does not see it at startup. Filled both the original with the apple, and under the bdu converted. The result is the same.



Rep: (0)
Clarifying the moment. After a long walk, I found this 10.13.1 in * .raw format.



Rep: (597)
* laccursedl
and what is there to wander, download and install, maybe it will be easier here, for starters
https://rutracker.org/…iewtopic.php?t=5413589



Rep: (0)
Here with rutsekera gag. Rostelecom does not let him.



Rep: (597)
* laccursedl



Rep: (0)
ty I understand it through r-drive?



Rep: (597)
* laccursedl
Yes



Rep: (0)
Good evening everyone. Tell me, I started the sound of alc256 on the laptop. The speakers work fine, but when I insert the headphones into slot 3.5, they do not work, although they can be seen. Tell me where to dig.
Works with AppleHDA

Post has been editedm1krot1k - 21.03.19, 19:18



Rep: (196)
m1krot1k @ 03.21.19, 17:16*
m1krot1k

iron in signature. there is no way out, contact the author.
the factory is correcthttps: //www.applelife.....hing-applehda.1171672/patch can be done by thishttps: //www.insanelyma…35018-hackintool-v204/change pins and tune thesehttps: //www.insanelyma…/981-pin-configurator/

Post has been editedkonondoyl - 21.03.19, 20:47



Rep: (3)
All good evening.

Faced a problem.
I run the Sierra installation. It started, the mouse connection screen appears, does not respond to my mouse.
I read somewhere that I need drivers, but I don’t understand what specific ones I need and where to put them too, for different resources different info.
Help with this moment.

Here are my specs

Processor: Intel Core i7-2600 3.400Ghz
Motherboard: Asus P8P67 PRO
Video card: NV GTX550 Ti;
Loader: Clover ??;
Mac OS X Sierra version;

Thank you in advance.



Rep: (196)
gen-ohm @ 03.21.19, 20:25*
gen-ohm

https: //www.applelife...-vzjat-keksty.2942933/On usb everything is solved by setting usb or inserting the necessary one in us.2.



Rep: (3)
https: //www.applelife...-vzjat-keksty.2942933/On usb everything is solved by setting usb or inserting the necessary one in us.2.


Yes, they have already helped in HP, for which they are thankful.
But with now I pushed with another problem.

Installed MacOS on an external hard drive.
The first time it starts up normally, I perform the initial setup, install a clover, select items in it, which I looked fromvideotimecode - 20th minute
I upload the fake.smc file to the other and 10.12 folders on the efi disk.
I reboot, the clover opens already from the external disk, I start the OS and get the following

Attached Image

Before this, everything was readable, namely
Attached Image

after everything goes no further


I rearranged the OS again, but this time I tried to install the latest version of clover at the very first launch.
The result, after a reboot, hangs on it

Attached Image


Tell me what could be the problem?
There is a suspicion that I incorrectly put a clover, that is, I choose the wrong items.

Post has been editedgen-ohm - 22.03.19, 01:52



Rep: (196)
https://github.com/raf...us-P8P67Pro-Hackintosh
https: //www.applelife……/asus-p8h67-xxx.33826/

Post has been editedkonondoyl - 22.03.19, 07:07



Rep: (3)


The problem that I described above was solved in the following way.
I installed MacOS, I installed clover, I chose download points for uefi and efi.
Appeared section EFI. On it copied to the folder 10.12 fake.smc
Then I went to a bootable USB flash drive with clover and copied the clover folder into the EFI partition on the external hard drive, where the OS is installed.
Bottom line, now everything runs without a flash drive and from an external hard drive.

If you don’t copy the contents of the clover folder from the USB stick to the hard disk into the efi partition, the OS does not boot.

It remains to solve the issue with the drivers.

Post has been editedgen-ohm - 22.03.19, 12:38



Rep: (597)
gen-ohm @ 03/22/19, 11:37*
On it copied to the folder 10.12 fake.smc

it is better to throw all keksta in the folder others



Rep: (3)
it is better to throw all keksta in the folder others


Tried, did not help.
Without copying the contents from the flash drive to the EFI partition, the system did not start.



If I understand correctly, in the article itself there are already just the necessary cakes for my motherboard, you just need to put them in the right place, Right?
Just in the header of the site there is ala some kind of file manager.

Post has been editedgen-ohm - 22.03.19, 14:47



Rep: (196)
gen-ohm @ 03/22/19, 10:50*
gen-ohm

correctly understood, there is a guide on it for files with firewood and kehty and inject keht do not forget. First, you configure with a flash drive, as the system is configured, then you can transfer the air folder to the disk, and store the flash drive separately for emergency.

Post has been editedkonondoyl - 22.03.19, 18:32



Rep: (0)
Hello!

Update released on 10.12.6, is it safe to update? The video will not fall off?


Full version    

Help     rules

Now: 07/25/19 5:48 PM