Assistant
REPLY |
Xiaomi Ninebot - Firmware | [Vehicle] |
Message#1 18.06.16, 18:02 | |
saved by jesus [offline] Group: Friendssavagemessiahzine.com Messages 1073 Check in: 14.03.11 Apple iPhone 7 Plus Reputation: 213 | Giroskuter Xiaomi Ninebot Mini / Pro / One - Firmware Purchase � | Discussion � | application �
Latest firmware at the moment: 1.4.0 (1-?) To upgrade to version 1.4.0, you need to use the latest version of the application, since Now the firmware is at the new address. Rollback:If the firmware version is higher than 1.3.1 - rollback is possible only through the programmer. If lower, then the DNS / OTA method. (see. Spoiler - Useful) Firmware reviews Based on user feedback. 1.1.7- firmware with the least restrictions: acceleration to 18 km / h, you can drive back without squeaking, suitable for aggressive driving (video), faster overclocking, maybe a little more power consumption.Feedback after rollback and comparison with othersfromSerge11. Speed limit depending on battery charge. With the loss of the rider - the bot rushes further 1.1.9 - more secure, withstands a slightly higher maximum speed (opinion). 1.2.2 - secure firmware, beeps. 1.2.8- the safest, not suitable for aggressive driving, squeaks when bumping into bumps, slows down, beeps when driving back. 1.3.1- adequate, beeping less than the previous one, safe for children, not as frisky as 1.1.7, and 43% will reduce speed to 17 km 1.4.0- the limit to 10 km / h is removed after a run of 1 km, but will decrease speed by 43% to 16.5 km Comparisons and reviews: Official history of changes in firmware (eng) 1.2.8 and 1.1.7 - opinionnebloody. 1.2.8 and 1.1.7 - opiniongogokostik. 1.2.8 and 1.3.1 1.3.1 comparison with 1.4.0 c 1.3.1 Post with firmware - here. Useful About gyro Downgrade firmware Xiaomi Monocoles and Ninebot Mini (if it is not higher than 1.3.1) by DNS / OTA What need a programmer to roll back / firmware Where to solder programmer for rollback Ninebot Mini Reset (password) scooter Steering wheel calibration (if driving left / right) Downgrade firmware for 1.1.7(English), do only on the version of the application not higher3.5.1(as relevant,if your firmware version is not higher than 1.3.1)! Original or fake - seeBMS versions Can I charge Minik by charging from Pro? addition Firmware 1.1.9 for rollback BMS Battery Firmware Firmware updated via Bluetooth using a mobile application. Do not rush to update immediately, pay attention toreviews ATTENTION! It is STRONGLY RECOMMENDED to UPDATE / REDUCE the bot firmware via APPENDIX version 3.6 !! Availablebrickdue to an error in the update mechanism! K There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonunder the messages to which you want to add links. If there is a user in the subject who wants to become a Curator and the correspondingRequirements for candidates, he can apply in the topicI want to be curator(after having studied the topic header and all materials for curators). Post has been editedmihadom - 24.10.18, 12:29 Reason for editing: Firmware 1.1.9 for rollback |
Message#2 18.06.16, 18:23 | |
saved by jesus [offline] Group: Friendssavagemessiahzine.com Messages 1073 Check in: 14.03.11 Apple iPhone 7 Plus Reputation: 213 | (original instructions in English) Important!You need to lower the firmware on the application versionnot higher than 3.5.1! 1) Install on Android deviceNinebot 3.5.1 application! 2) Connect to wifi, open wifi connection settings on - advanced or additionally 3) In the settings, select a static IP and write the DNS1 address107.170.15.247. It is possible through the program® Set DNS. Manual method: Sometimes you need to specify to assign the IP address itself to the device, for example: IP - 192.168.0.5 (the last digit should be different from the address of the router) Mask - 255.255.255.0 Gateway - 192.168.0.1 (the address of the router may be different and be 192.168.1.1 or otherwise, you can find out in the connection properties) DNS -107.170.15.247- our replaceable DNS. 4) Go to the ninebot application and upgrade to 1.3.0 (in fact, this is firmware with version 1.1.7) Do not forget to return back the wifi settings back and do not let the application update to 1.2.8! An example of a successful rollback Post has been editedid_snake - 01.05.17, 15:03 Reason for editing: Example -------------------- |
Message#3 18.06.16, 20:18 | |
Only better [offline] Group: Friendssavagemessiahzine.com Messages 1692 Check in: 02.08.13 Apple iPhone 6s Plus Reputation: 182 | Thank you for creating a separate topic. Still not bad would be links to all versions that can be pulled out near the instructions for downgrade leave. :) -------------------- Phone: iPhone 6s Plus, Clock: Apple Watch Sport, Tablets: M $ Surface Book (Core i7, 16 GB RAM, 512 GB SSD)|iPad Pro 9.7 LTE. |
Message#4 18.06.16, 20:59 | |
Novice [offline] Group: Active users Messages 32 Check in: 06.02.10 Reputation: 1 | on the link video how to make a reset mini, in case it requires a code for pairing by bluetooth https://youtu.be/UsewY6gBOZ4 |
Message#5 18.06.16, 21:25 | |
Visitor [offline] Group: Active users Messages 19 Check in: 31.05.16 Reputation: 0 | From myself I would add that after a short time the steering column loosened at its attachment to the bot, took out the red gum and tightened the two bolts with the hexagon. A little later, the same helmsman was loosened at the length adjustment site, under the sticker 4 screws ... I also pulled it up. Judging by the reviews, I’m not the only one, and accordingly it is necessary to include these procedures in the pre-launch launch probably. |
Message#6 19.06.16, 00:33 | |
a guest [offline] Group: Users Messages 1 Check in: 19.06.16 Apple iPhone 6s Plus Reputation: 1 | Ben, this is Daniel, ah nid help! How to roll back from 1.1.8 to 7? Who has the firmware? Sign-up passwords? 23.00 found this: Instructions for rolling back the firmware Ninebot Mini to 1.1.7 Method from Alexander Bykov and his DNS server: 1) Take the Android device 2) Connect to wifi with internet and open wifi connection settings on android device 3) In the IP address settings, select static and write the DNS 1 and DNS 2 address 107.170.15.247 4) Go to the ninebot application and upgrade to 1.3.0 (in fact, this is firmware with version 1.1.7) Do not forget to return back the wifi settings back and do not let the application update to 1.2.8. 0.35 Updated down, I'm going to try. 1.05 Cheers! I brought the bot back to life! He began to work as before, he collapses back, but he doesn’t like the new firmware, and of course the start! But with the right device. 1) Take the iPhone 2) Connect to wifi with internet and open wifi connection settings 3) In the DHCP settings, we write the DNS address 107.170.15.247 4) Go to the ninebot application and upgrade to 1.3.0 (in fact, this is firmware with version 1.1.7) Do not forget to return back the wifi settings back and do not let the application update to 1.2.8. Do not thank! #NinebotMini #ninebotdowngrade Post has been editedalexander666in - 19.06.16, 01:14 |
Message#7 19.06.16, 00:49 | |
Visitor [offline] Group: Active users Messages 19 Check in: 31.05.16 Reputation: 0 | Rolled back from 1.2.8 to iphone, but the essence is the same ... rolled back by this instruction. |
Message#8 19.06.16, 14:29 | |
saved by jesus [offline] Group: Friendssavagemessiahzine.com Messages 1073 Check in: 14.03.11 Apple iPhone 7 Plus Reputation: 213 | [email protected], 18:23 Still not bad would be links to all versions that can be pulled If there is, throw add, did not find links to the firmware itself. -------------------- |
Message#9 20.06.16, 11:42 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 172 Check in: 20.10.11 Samsung Galaxy S6 Duos SM-G920FD Reputation: 7 | 1.1.7 http: //apptest.ninebot...Mini_Driver_V1.1.7.zip apptest dot ninebot dot cn / appversion / appdownload / NinebotMini / v1.1.7 / Mini_Driver_V1.1.7.zip 1.2.7 http: //apptest.ninebot...Mini_Driver_V1.2.7.zip apptest dot ninebot dot cn / appversion / appdownload / NinebotMini / v1.2.7 / Mini_Driver_V1.2.7.zip 1.2.8 http: //apptest.ninebot...Mini_Driver_V1.2.8.zip apptest dot ninebot dot cn / appversion / appdownload / NinebotMini / v1.2.8 / Mini_Driver_V1.2.8.zip 1.3.1 http: //apptest.ninebot...Mini_Driver_V1.3.1.zip apptest dot ninebot dot cn / appversion / appdownload / NinebotMini / v1.3.1 / Mini_Driver_V1.3.1.zip Attached files Mini_Driver_V1.1.7.zip(61.83 KB) Mini_Driver_V1.2.7.zip(63.2 KB) Mini_Driver_V1.2.8.zip(63.12 KB) Mini_Driver_V1.3.1.zip(63.33 KB) Post has been editedDekdekdek - 04.07.16, 16:55 -------------------- Hire, damage. |
Message#10 21.06.16, 00:37 | |
a guest [offline] Group: Users Messages 9 Check in: 02.06.16 Reputation: 0 | |
Message#11 22.06.16, 20:59 | |
Novice [offline] Group: Active users Messages 35 Check in: 10.07.10 Xiaomi Redmi Note 3 Prime Reputation: 0 | Today I made a rollback from 1.2.2 if I was not mistaken, now 1.1.7. The scooter rides visibly more vigorously and accelerates dynamically. Quite pleased! He managed to accelerate to 20km. If you believe the testimony in the application. The screen is fresh maximal 19km in it. -------------------- Who understood life, he is in no hurry to work! |
Message#12 26.06.16, 21:25 | |
Visitor [offline] Group: Active users Messages 28 Check in: 29.01.10 Reputation: 0 | Dear comrades, there is such a problem: I took a new device out of the box, charged, launched, installed the software from the off site (android), registered, offered to upgrade to the latest firmware. Now the ninebot, when turned on, flashes intermittently and beeps. With android phone does not connect. I took an iPhone, connects, but writes cpu start error 29 -------------------- Xiaomi redme 3 3/32 |
Message#13 26.06.16, 21:51 | |
Novice [offline] Group: Active users Messages 32 Check in: 06.02.10 Reputation: 1 | beltrami, I think you hit. on the raw firmware killer mini 3.6 here on the forum also howl began http: //forum.electricu...and-beeping-wont-pair/ |
Message#14 26.06.16, 22:30 | |
Visitor [offline] Group: Active users Messages 28 Check in: 29.01.10 Reputation: 0 | I read that forum, so far there is no solution. -------------------- Xiaomi redme 3 3/32 |
Message#15 26.06.16, 23:29 | |
Visitor [offline] Group: Users Messages 11 Check in: 21.09.09 Reputation: 0 | I tried to roll back to 1.1.7 from 1.2.8 through the Iphone. I register in the wifi settings in DHCP, DNS 107.170.15.247. Then I go to the ninebot, update the firmware and the application says that you have the latest firmware installed. What am I doing wrong? |
Message#16 28.06.16, 08:00 | |
Novice [offline] Group: Active users Messages 35 Check in: 10.07.10 Xiaomi Redmi Note 3 Prime Reputation: 0 | Try through the android to do this operation, the iPhone is so good that everything in it is done through the ass, to the detriment of the user. -------------------- Who understood life, he is in no hurry to work! |
Message#17 28.06.16, 10:19 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 333 Check in: 18.12.12 Xiaomi Mi 6 6/64 Reputation: 1 | I bought it, got it to the phone and it was updated, now it beeps, what should I do? -------------------- Xiaomi |
Message#18 04.07.16, 16:03 | |
Novice [offline] Group: Active users Messages 33 Check in: 09.07.08 Reputation: 0 | |
Message#19 04.07.16, 23:15 | |
Only better [offline] Group: Friendssavagemessiahzine.com Messages 1692 Check in: 02.08.13 Apple iPhone 6s Plus Reputation: 182 | Updated from iPhone from 1.1.7 to 1.3.1. Chic firmware. The apartment is visually more stable and stable. But now I can not push forward so that he rode by himself :( Tomorrow I'm going to Kiev, check it out there. -------------------- Phone: iPhone 6s Plus, Clock: Apple Watch Sport, Tablets: M $ Surface Book (Core i7, 16 GB RAM, 512 GB SSD)|iPad Pro 9.7 LTE. |
Message#20 04.07.16, 23:19 | |
Novice [offline] Group: Active users Messages 31 Check in: 14.07.07 Apple iPhone SE Reputation: 3 | Damn, I ride on 1.1.9 so cool, I am absolutely satisfied with everything, beeps a little, rejects slightly, allows acceleration to 18.3, the charge eats not much .. That would be someone who compared 1.1.9 with 1.3.1 .. FIG know, maybe firmware has become really nicer? I myself would not venture to check, perhaps. -------------------- Ninebot Mini Pro Black v.1.1.9 (BMS v.1.0.5) |
Message#21 04.07.16, 23:26 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 1293 Check in: 03.06.11 Xiaomi Mi 5S 3/64 Reputation: 99 | I have 1.2.2, you can consistently go 16-17, briefly you can accelerate to 18-19. The backward squeak. Lives long, 25km and another 20% of the charge remains. Also reluctant to take risks, because even the firmware does not have such for downloading, exclusive, to label it. -------------------- Xiaomi Mi5S 64Gb MIUI v9 download/ Android 7+Pebble 1 + Pebble Time SteelSony Ericsson Xperia Mini Pro Sk17/ Android 2.3 Xiaomi Ninebot Mini/ custom v7.6.0 / 1051 km |
mobile version | Now: 04/28/19, 19:20 |