[X]Assistant

[kestua]

HUAWEI HG532e - Discussion

FAQ - read first, then write

• In the subject are allForum Rulesand10 commandments beginner | who is hard to master Forum Rules.
  
• Discussion of devices not related to this topic is prohibited. If the theme you need for a specific model does not exist - create it.
  
• Instead of saying “Thank you!” Use. If you have less than 15 posts - click on the button.under the message where they helped you, and write thanks.
  
• Useful topics to note:Forum FAQ, How to search the forum?, How to remove the image under the spoiler., Wi-Fi Questions / Answers
  

Specifications:

Power: 12 VDC, 0.5 A
Connector type: barrel

CPU1: Ralink RT63365E (500 MHz)
FLA1: 4 MiB (Winbond W25Q32BV)
RAM1: 32 MiB (Winbond W9425G6JH-5)

Expansion IFs: none specified

WI1 chip1: Ralink RT5392L
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2: 2
WI1 antenna connector: ms156 (aka MiFi 2200)

ETH chip1: Ralink RT63365E
Switch: Ralink RT63365E
LAN speed: 10/100
LAN ports: 4



Dimensions: Height 31 mm Width 145 mm Thickness 110 mm
Weight 360 g
Supports DSL ADSL / ADSL2 / ADSL2 + Standard 802.11 b / g / n
Internal antenna type: WLAN antenna: built-in with 2 * 2 MIMO support
The range of frequencies Wi-Fi 2.4 GHz
Information security AES encryption, TKIP, WEP (64/128), WPA-PSK, WPA2-PSK
Ethernet Ports Ethernet Ports 4 * LAN Speed ​​of LAN ports: 10/100 Mbps
Power: Adapter
HG532e - without usb-although you can solder, as in hg532s
solder a capacitor, etc.
wiki.openwrt-huawei-hg532s
wikidevi-Huawei_HG532e

Manuals:

• Port forwarding (English manual)
  Huawei_HG532e_DHCP.pdf(825.51 KB)
  Huawei_HG532e_PoPPoE.pdf(753.26 KB)
  
• HUAWEI HG532e to enable modem in bridge mode:
  
• problem solving: if reset to factory settings
  
• Huawei Hg532e with 40MHz channel width (300mbit)
  

Modem upgrade

Connecting an external antenna

It has 2 internal antennas and a pigtail.

Another connection option
external antenna (te156)

USB

HG532e - without usb-although you can solder-on the board there is a place + solder the capacitor-100uF / 16V + 2 resistors 15k + ...
hg532s.7z(8.84 MB)

A photo:

Firmware:

• 
  HG532eV100R001C02B017_upgrade_main.zip(3.54 MB)
  - Chinese firmware have the ability to assign Wan to Lan 1
  
• Dapmy firmware under hg532e / s
  
• HG532e_V100R001C81B025_Firmware_general_05012EJW.rar(3.49 MB)
  
• HG532eV100R001C81B025 MTS Russian firmware.rar(3.49 MB)
  
• HG532eV100R001C108B012 Ukrtelecom firmware .rar(3.39 MB)
  
• HG532eV100R001C136B011 Belarusian firmware.rar(3.4 MB)
  
• HG532e_FIRMWARE_V100R001C01B030_General_05021CFS.zip(14.63 MB)
  
• hg532s.7z(8.84 MB)
  

After the firmware do reset to factory settings !!
Alternative firmware dumps for the programmer
Useful post.

Useful

• Lonig and superuser password on the Belarusian firmware
  
• UART connect.
  
• Disconnecting the burned ADSL chip from the power supply.
  
• Pinout processor RT63365
  
• For newbies.
  
• Dump QBR-2041ww
  
• Disaster recovery and / or flashing someone else's dump via UART
  

The firmware does not support the "wifi repeater" function!
official site

Post has been editedAndrewP_1 - 23.04.19, 10:53

Reason for editing: Disaster recovery and / or flashing someone else's dump via UART

[the_spawn]

Someone tell me how to "pull" the firmware from the router? Own firmware HG532c in which there is already an FTP, a router with Spanish firmware. I would like to post it on the forum. Only the program method (usb, pc, twisted pair) without programmers and a soldering iron is interested.

Posted on 11/27/2016 19:15:

(update, firmware for Spain, English language)

[yac9I9]

the_spawn[s] hg532c
It is assembled on realtek, there is firmware in the network

Post has been editedyac9I9 - 27.11.16, 22:29

[voland1992]

sergprotoss,thank.

Shark549,I can not say exactly. I have already disconnected the Internet which I used with the help of this modem. I did as a friend wrote above. Well, the modem is turned on already, and does not hang with the power and ADSL indicators turned on. Looks like it helped.

[the_spawn]

Yac9I9 @ 11/27/2016, 10:46 PM

the_spawn[s] hg532c
It is assembled on realtek, there is firmware in the network

Well then order. I just saw that only for a model without a flash drive firmware in the branch. I thought to help, this router was lying around.

[foxx_78]

Hello! Guys and who knows how it can change the poppy address? If at all possible ...

[Rom007]

Hello everybody please tell me is it possible to log in on this roter on telnet ??????

[yac9I9]

Rom007,There is a semblance of telnet in the firmware from mts, there is no sense in it because it is truncated.

[bogdanxp]

voland1992 @ 10.29.16, 20:54

When I turn it on to the network, the DSL indicator is constantly on. Whatever I do, this indicator is always on. Neither the reset button does not help, neither is switching from the outlet, nor by the on / off button. It just burns always.

The same problem appeared by itself, the modem did not touch at all. Soldering the reset button did not help.

Post has been editedbogdanxp - 07.12.16, 23:34

[038092]

Tell me how to flash a router just for unlinking from Ukrainian Ukrtelecom, that would work with other providers. What firmware to install, and if you can instruction in a nutshell)

[038092]

And yet, I just realized that there is an Internet connection through a telephone cable, how then can other providers connect an ordinary Internet cable?

[yac9I9]

038092,This is an ADSL modem, it connects only via a telephone line. For other providers, you need a Wi-Fi TP-LINK TL-WR841N router, etc.

[yac9I9]

Anyone who put the firmware from 532s printer could attach usb? I just can’t get hp 1018 to work, I don’t even know in the printer a cant or in a modem.
This printer does not support this operation.

Post has been editedyac9I9 - 18.07.18, 17:11

[Cthutq_03]

Good day to all! There is a great desire to make friends two WIFI modems as a bridge There is a modem router Huawei from intertelecom Huawei EC 5321 and its relative from Ukrtelecom HUAWEI HG532e.
The need to use a second modem as a router for distribution by wire, and he would take on WIFI, but I can not go to the web of this asshole to see what and how, writes the network is not recognized. Probably re-tried everything and IP addresses wrote all sorts of results 0. someone can know how to visit him. and whether it is worth bothering at all.

[sergeovip]

Hello! I patched the HG532eV100R001C136B011_upgrade_main.rar.rar modem with this firmware, it is the second one in the list of firmware, the Wi-Fi stopped working and a lot of settings were missing, including the firmware update menu, please tell me how to flash it with another firmware? : '(

[l3n1n-ua]

sergeovip
reset to factory settings after the firmware did?

[sergeovip]

Yes, and I tried to turn it on with a clamped reset, in general then it does not connect to it, and different browsers.

[yac9I9]

sergeovipctrl + f5 in the browser. And in this firmware, it seems, it is necessary to go under the "superadmin".

[sergeovip]

yac9I9,Thank you very much! I found how to go under superadmin and sew! If anyone needs:
Login: superadmin
Password:! @HuaweiHgw
And if there is a skinte, please, a link to the factory firmware, so that the log of the mts or something else would be.

Post has been editedsergeovip - 20.12.16, 19:11

[yac9I9]

sergeovipIn the Ukrtelecomov firmware, the huawei icon but a certificate like in Ukrainian(and then it seems only to flash through the tftp server).

Post has been editedyac9I9 - 18.07.18, 17:12

[tukmar]

sergprotoss, the way with nippers one hundred percent works to bite off the reset button.