Assistant
REPLY |
DD-WRT - alternative firmware | [firmware] General theme. FAQ, software discussion, tips, problem solving |
Message#1 24.03.16, 00:39 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | OpenWrt / LEDE (General theme) | Build OpenWrt / LEDE from source | Collect bin (dump) for the programmer | Upgraded UBOOT loaders DD-WRT FIRMWARE DD-WRT- free alternative firmware for wireless routers Latest version:See the official FTP The forum decided to post images under the spoiler Difference DD-WRT firmware from factory First, it is worth noting that DD-WRT firmware is an operating system based on the Linux kernel. Even with the default settings it has a very wide functionality, much wider than in the factory firmware. Built-in components such as FTP server, Samba, WOL and more. Through the Web interface, detailed statistics and load on the channels of the local, wireless network and the Internet are available, as well as the load on the processor and the memory of the router. If you configure the router to install additional packages, you can turn your router into a home media server. A connected hard drive with a torrent client installed, broadcasting ITPV via HTTP, for viewing via wi-fi. If you have a TV with DLNA standard support, you can connect the TV to the router and watch IPTV, as well as watch movies from your hard drive. Opportunities 13 languages (including Russian) 802.1x (EAP (Extensible Authentication Protocol) encapsulation over LANs) Access Restrictions Adhoc mode Afterburner Client Isolation Mode Client Mode (supports multiple connected clients) Client Mode WPA DHCP Forwarder (udhcp) DHCP Server (udhcp or Dnsmasq) DNS forwarder (Dnsmasq) DMZ Dynamic DNS (DynDNS, easyDNS, FreeDNS, No-IP, TZO, ZoneEdit, custom, and others) Hotspot Portal (Sputnik Agent, Chillispot) IPv6 Support Jffs2 MMC / SD Card Support (hardware modification required) NTP client in a client-server basis Ntop remote statistic OpenVPN Client & Server (only in -vpn build of the firmware) Port triggering Port Forwarding (max. 30 entries) PPTP VPN Server & Client QoS Bandwidth Management (Optimize for Gaming and Services / Netmask / MAC / Ethernet Port Priority) QoS L7 Packet Classifier (l7-filter) RFlow / MACupd Routing: Static entries and Gateway, BGP, OSPF & RIP2 via (BIRD) Samba FS Automount Syslog to remote server Rx / Tx Antenna (Select or Auto) Uptime / Processor Utilization Site survey SNMP SSH server & client (dropbear) Startup, Firewall, and Shutdown scripts (startup script) Static DHCP Assignment Style (Changeable GUI; v.23) Supports New Devices (WRT54G V3, V3.1, V4, V5 and WRT54GS V2.1, V3, V4) Telnet server & client Transmit Power Adjustment (0-251mW, default is 28mW, 100mW is safe) UPnP VLAN Wake On Lan client (WOL) WDS Connection Watchdog WDS Repeater Mode Wireless MAC Addresses Cloning Wireless MAC filter WMM (Wi-Fi Multimedia QoS) or Wireless Multimedia Extensions (WME) WPA over WDS WPA / TKIP with AES WPA2 Xbox Kaid (Kai Engine) Web Interface Screenshots List of supported devices How to flash (install) DD-WRT factory-to-ddwrt.bin- file for installing DD-WRT from under the router's native firmware. webflash.bin- file for updating from already installed DD-WRT. For some models, only one file is available for all operations. Forthe originalDD-WRT installations: In the address bar of the browser we typehttp://192.168.1.1orhttp://192.168.0.1,depends on the router, enter the data for authorization and update the filefactory-to-ddwrt.binthrough the standard update menu in your router. After some time, the router will reboot, after which you will see the updated interface (DD-WRT's address is 192.168.1.1 by default). On the main page when you first start you need to specify the username and password for administration. Firmware dd-wrt installed, you can proceed to configure. (It is also recommended to do a reset to the factory settings after the firmware and before the setting) If you have problems not being able to log into the DD-WRT admin panel after the firmware, go to the network connections on your computer and make sure that the ip addresses are issued correctly: ip: 192.168.1.xxx (the last digit may vary) mask: 255.255.255.0 gateway: 192.168.1.1. If the addresses are different, then the easiest option is to restart the network card (on and off then the network will again request the addresses via dhcp), if this did not help, manually enter, for example, ip 192.168.1.2, mask: 255.255.255.0 gateway: 192.168. 1.1 and try to enter the browser again at 192.168.1.1. Going to the web interface of the router, the tab "Settings" - "Basic Settings" - find this item: Must be "DHCP server", if not, put. The fact is that if there is a "redirection" your router will redirect the provider's IP address to your computer, that is, it will work as a switch. ForupdatesDD-WRT already installed: In the DD-WRT menu, select “Administration” - in the submenu, select the “Firmware upgrade” item. Click on the button “select file” and specify the firmwarewebflash.binwhich was downloaded earlier. Click on the “Upgrade” button, the software update process will begin. Options for rolling back to stock (native) firmware Important!If you do not know how to return the stock on your router or do it for the first time, before performing any operations with the router, it is better to ask in this topic or topic visited by your router.Not all methods are universal., each router needs its own approach.
FAQ AT:How to properly flash the router? ABOUT:
ABOUT:Press the reset button and hold it. After 30 seconds, turn off the power without releasing the Reset button. After another 30 seconds, release the Reset, turn on the power, wait until any other light on the router lights up except for the power supply, or the PC does not see the router, again we hold the Reset. Wait another 30 seconds and release the reset. AT:How to view the system log? ABOUT:You must first enable the syslogd service in the Services tab. (The field with the server name can be left blank.) And follow the linkhttp://192.168.1.1/Syslog.asp,The page can be accessed only through the address bar. If you don’t open the System Log page, then you have an old firmware version, and the log messages are written to the file / var / log / messages, which can be viewed with the commands cat, tail, more, less, etc. AT:How to connect telnet to the router with DD-WRT? ABOUT:Open a session in telnet client with the address of the router (by default 192.168.1.1) and the standard port (23). When prompted for a username (login), enter the standard root name - even if you changed the username to log in to the web interface. And when prompted for a password, enter the password you set for the web interface. AT:How to load into the router not one script, but two? ABOUT:Put the & sign at the end of the first script and load the second one. If you later need to load the third one, put the & sign at the end of the second script, etc. AT:The Russian language does not work. Why? ABOUT:Most likely the problem is in the firmware, the Russian works again in all releases of 2016. Also in the old stable versions. Q: "retracker.local" stopped working, what to do? ABOUT:It is necessary to turn off "No DNS Rebind" in the section "Services" - "Services" - "DNSMasq". Q: Can I enable HTTPS? ABOUT:You can, but to use it you need a special browser. Also, if you uncheck HTTP and leave only HTTPS, then you will most likely have to do a reset, since you will not access the Web GUI through a regular browser. (If you uncheck both checkboxes, you won’t go to the web interface at all) Q: Does Universal Plug and Play (UPnP) work? ABOUT:Yes, but you need to enable it manually, in the section "NAT / QoS" - "UPnP" Q: I climbed in the settings and now I have a low rate of return or reception, why? ABOUT:Most likely you have enabled "QoS", check if it is, then disable it. Q: I set the TX Power to 20, but shows 16 dBm, why? I know for sure that the router can work on this power! ABOUT:Perhaps the power is limited, because of the region you selected in the WiFi settings.Change to another, for example "US". Q: TX Power has set 20 (or 21), the region is needed, but the router shows 19 dBm, why? ABOUT:Maximum power can be obtained only on channel 6. Q: How to set up a router in repeater mode? ABOUT: Instruction Q: How to reassign a burned out WAN port to a LAN? ABOUT:We readhere. Q: How to get the maximum WiFi speed on routers with N mode ABOUT:We readhere. Q: It is written on the official website that I lose the warranty when installing DD-WRT. This is true? ABOUT:Theoretically, yes, but you can flash the stock, and most routers will be out of the box. Q: I need a built-in OpenVpn, is it in this firmware? ABOUT:Yes, but only in firmware for routers with more than 4 mb. of memory. (You can find out how much flash memory in your router model, for example, inWikiDevi) Q: I need the router to automatically turn on and off WIFI on a schedule, DD-WRT can it? ABOUT:Yes that'sinstruction Q: DD-WRT does not allow the provider’s local resources (personal account, etc.), what to do? ABOUT:You just need to remove one tick.instruction Q: How to change the TTL value on the router? ABOUT:Here isinstruction Q: How to enable multicast on DD-WRT? ABOUT: Instruction Q: How to make the router work as a switch, but with wifi? ABOUT: Instruction Q: How to make the router automatically restart at the right time? ABOUT: Instruction Q: If you don’t see the neighboring computers on the router’s local network (for example, on Samba) ABOUT: Instruction Q: I switched the language to Russian and in some places (for example, on the tab of the MAC filter of a wireless network) there are cracks. ABOUT:Yes, this is a bug; it is very easy to overcome - by forcibly switching the page encoding in the browser to UTF-8 (for example for chrome there is an encoding menu plugin)instructionAlso, this bug is missing in the version of r27086 and earlier. Q: How to activate the firmware on Ubiquiti routers. ABOUT:No Only buy a license for dd-wrt on the official site. There are no working key generators. Q: My provider has local sites in the .local zone, having trouble accessing them. How to be ?. ABOUT:Here isinstruction Q: I need to block a site on my home network, for example, youtube. How to do it? ABOUT:Here isinstruction Q: I heard that using dd-wrt, you can somehow access Pandora, HBO Now, Spotify, Amazon Video and Netflix outside the US without using vpn. How? ABOUT:Here isinstruction Q: I need to get internet via wifi and distribute it as usual, that is, connect the router with a "client". Can this be done? ABOUT:Yes that'sinstruction useful links
Download DD-WRT
Important!Firmware for routersUbiquitipaid Key generatorsdoes not exist Topic Curator: Topic with no curator Post has been editedstp101 - 08.03.19, 23:48 |
Message#2 24.03.16, 10:51 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | Reassign the burned down WAN port on the LAN, in the DD-WRT firmware Open the addresshttp://192.168.1.1/Vlan.asp Mirror the values from the portWanonLAN4 Checkbox"W-1 port"remove and put on"W-0 port". Checkbox"Port 4-0"remove and put on"Port 4-1". Attention: the page was "hidden" due to security concerns, as incorrect configuration may result in hard reset and flashing. The second option, reassigning the WAN port via the console Open the administrative panel of the router and enter the Code: nvram set vlan0ports = "1 2 3 5 *" nvram set vlan1ports = "0 4 5" nvram commit reset A source:http://routers.in.ua/p...j-port-wan-na-lan.html Post has been edited_Danil_ - 24.03.16, 11:01 |
Message#3 24.03.16, 11:57 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | How to get the maximum WiFi speed on routers with N mode and only (2.4 GHz). On DD-WRT firmware Wireless Network Mode:N-Only (2.4 GHz)(if some device cannot join NG-Mixed) Channel Width:never mind, but theoretically the HT40 is better. (But not in a noisy area) Wireless Channel:Auto or1,6,11 I recommend 6 to get maximum transmitter power. Regulatory Domain:You can use your country, but to remove power limits, use United_States (channels 1-13 are available). TX Power:You can do it all, but remember, the WiFi module can overheat, and the speed may drop. Use 1-2 less than the maximum, the best is the 6th channel. (If you put 30, and 20 is available, the router will simply use 20) (Also in some routers you can install hacked art) Antenna Gain:Leave 0 Noise Immunity:Enable RTS Threshold:It does not matter, but if loss of leakage is noticed, I recommend to enable it. Short Preamble:Enable (VERY old smartphones, etc. may not support) Short GI:Enable DTIM Interval:1 or 2, I use 1. (I recommend 1 if you are using smart TV) Beacon Interval:100-200, if there is a VERY lot of WiFi nearby, then leave 100. (Increasing the value to 200, win a few percent of the bandwidth.) WMM Support:Enable Sensitivity Range (ACK Timing):1000-1500 (Default: 2000 meters) If younotuse WiFi on long distances, on the street for example, feel free to put 1000,I do not recommend setting 0, this is either Auto in Atheros, or disables this function altogether, in auto mode, the speed decreases, as it takes time to determine the value. Security Mode:WPA2 Personal WPA Algorithms:AES This is purely my recommendation, I use these parameters on my TP-Link TL-WR841ND v9, and I calmly get 150 Mbps in the local network via WiFi. But keep in mind though the router over WiFi gives 300 Mbps (theoretical speed), you also need to have a WiFi adapter capable of getting the speed provided by the router. If I'm wrong in something, correct me. Post has been edited_Danil_ - 05.03.17, 19:48 Reason for editing: Corrected errors and added |
Message#4 01.04.16, 21:59 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2960 Check in: 04.01.12 Pocophone F1 6/64 Reputation: 199 | on a computer for lan Internet tupit) not all but half of the sites loaded for a long time, everything flies directly (if you put this please, will it help?) (WR841N v8 00000000) Post has been editedSuRMaJ - 01.04.16, 23:41 |
Message#5 02.04.16, 08:22 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | |
Message#6 02.04.16, 08:29 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | Important!Bild29387 --- 2016/03/31 do not put it! This build causesbootloopOn devices with a chip from Atheros, and on other devices there may be other problems. Post has been edited_Danil_ - 02.04.16, 08:30 |
Message#7 02.04.16, 17:27 | |
a guest [offline] Group: Users Messages 3 Check in: 05.03.15 Reputation: 0 | Important! Build 29387 --- 2016/03/31 do not put! This build causes a bootloop on devices with an Atheros chip, and other devices may experience other problems. Found this entry only after bootloopa on tp-link 743nd v1. How is it possible to disassemble it? Or just flash to unsolder and fill with something? |
Message#8 02.04.16, 19:57 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 867 Check in: 28.12.07 Xiaomi Redmi 4 Prime Reputation: 7 | What about the D-link DIR-625 H \ w Ver.C1, F \ W Ver.3.00 (P / N BIR 625ANA ... C1) and Linksys WRT610N are not supported? |
Message#9 02.04.16, 22:20 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 221 Check in: 01.02.16 Samsung Galaxy S3 GT-I9300 Reputation: 8 | Good day! Successfully changed today the stock firmware for for TL-WR841N v8 according to the instructions from the header. Thank you very much! One small nuance: I could not find connection protection points in the interface Security Mode: WPA2 Personal WPA Algorithms: AES I would be very grateful if you send a tip to koumiss. |
Message#10 02.04.16, 22:34 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2960 Check in: 04.01.12 Pocophone F1 6/64 Reputation: 199 | |
Message#11 02.04.16, 22:51 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | One small nuance: I could not find connection protection points in the interface Security Mode: WPA2 Personal WPA Algorithms: AES Tab "WiFi" - "Security", where the password is entered. Posted 04/02/2016 22:51: SuRMaJ, ftp://ftp.dd-wrt.com/b…2/tplink_tl-wr841ndv8/ Post has been edited_Danil_ - 02.04.16, 22:59 |
Message#12 03.04.16, 17:44 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 221 Check in: 01.02.16 Samsung Galaxy S3 GT-I9300 Reputation: 8 | _Danil_, Thank you, figured out. Another question: what you need to tweak to IPTV showed more stable. I mainly watch the Eden playlist (the provider is a complete miser - pushes IPTV of the so-called "Partner" at a crazy price) on Samsbng SmartTV UE40ES6717U via a cord from a router. They tortured the constant freezing of the image (especially in the evening, when the load on the server increased), we often had to reboot the router. Therefore, in principle, I reflashed my TL-WR841N v8 on DD-WRT. The situation has improved: I didn’t do a reboot in a day’s work, but the picture still hangs on many SD channels. Maybe you can still somehow improve the situation? Post has been editedcostyasaprykin - 03.04.16, 18:33 |
Message#13 06.04.16, 04:09 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 432 Check in: 19.10.12 Reputation: 29 | Tell me please. I have a tl-wr841n router. Can I install the firmware tl-wr841nd? Without the letter "d" did not find. thank |
Message#14 06.04.16, 14:40 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 318 Check in: 09.07.11 Samsung Galaxy S7 SM-G930FD Reputation: 39 | |
Message#15 16.04.16, 00:49 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 354 Check in: 11.10.13 Reputation: 3 | How to roll back firmware to native TPLINKOVSKU? |
Message#16 18.04.16, 11:02 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 27.08.11 Asus zenfone 5 Reputation: 3 | [email protected], 00:49 How to roll back firmware to native TPLINKOVSKU? http://proadminz.ru/vo...ki-tp-link-tl-wr842nd/A way for many models! Post has been editedJohnyJah - 18.04.16, 11:03 |
Message#17 22.04.16, 18:09 | |
Well this is very AND VERY !!. [offline] Group: Friendssavagemessiahzine.com Messages 632 Check in: 04.03.16 Alcatel IDOL 4S Windows 10 Reputation: 19 | Experts welcome, tell me, is there a wps function on dd-wrt? where does it run? -------------------- killed and ate1_ nothing personal / case only |
Message#18 13.05.16, 12:32 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 98 Check in: 27.09.14 Honor 9 Reputation: 9 | At the sale price ($ 5,955 with a two-year warranty) purchased the NETGEAR R6300-100PES router, which turned out to be the second hardware version of the R6300v2 (BCM4708A0 800 MHz; 2 cores; 256 MB RAM; 128 MB ROM; AC1750; Wi-Fi 2.4GHz and 5GHz, including AC; 4 LAN ports and 1 WAN over 1Gbit; USB 2.0 and 3.0 each). I have not dealt with NETGEAR products for a long time and was quite disappointed with the possibilities of the stock firmware, which was also dubbed last in technical support. In order to avoid depression, I installed DD-WRT and the router opened, began to delight, the possibilities of the press, there is something to learn. I just can not understand with the updates ... I did everythingbased on the DD-WRT Wiki, put the one-year-old recommended build 26138 (ftp://ftp.dd-wrt.com/b…r6300v2-webflash.bin). But I see that the beta is laid out with enviable periodicity, in particular, under my router. Today 29621 of 10 May. How often are people updated? Is it worth it to update or better to sit on the type-stable version and not twitch? |
Message#19 14.05.16, 12:38 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 27.08.11 Asus zenfone 5 Reputation: 3 | Well, you roll new and test -) What prevents? |
Message#20 14.05.16, 15:36 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 98 Check in: 27.09.14 Honor 9 Reputation: 9 | [email protected], 16:38 Well, you roll new and test -) What prevents? For the first time, I rolled DD-WRT, I don’t know how they have stability there ... And there’s very little information, neither normal forums nor FAQs. |
Message#21 14.05.16, 20:53 | |
Visitor [offline] Group: Active users Messages 15 Check in: 26.04.12 Reputation: 0 | How does the transition to DD-wrt from open-wrt occur? Just after two firmware? |
mobile version | Now: 06/05/19 16:39 |