[X]Assistant

[dima101097]

Doogee Valencia 2 Y100 Pro - Firmware
Y100 Pro
Description | Discussion пїЅ | Purchase пїЅ | Firmware пїЅ

Drivers and Utilities

Pack-Flashtool (there are drivers in the archive)
SP Flash Tool v.5.1408.00 + driver
ADB driver for Windows 7 x64 "

Official firmware

Official firmware for 20140710
DOOGEE-Valencia2_Y100pro-Android5.1-R08-20151229
Bol backup for FT

Unofficial firmware

CyanogenMod 12.1 UNOFFICIAL STABL
Alternative Rom v2.1 Black Edition
Resurrection Remix 5.5.9 FIX
BlissPop v4.0.3
Alternative Rom v3.0 Black Edition
AOSP (Android Open Source Project)

Recovery, Root

TWRP_3.0.2 Material
TWRP 3.0.2
TWRP 3.0 FIX MTP
CWM and TWRP 3.0 recovery
ROOT without PC via stock recovery
Turn off return to stock recovery

Instructions

Instructions for firmware via SP Flash Tool
Installing OTA after rutting and interfering with the System
Install Recovery without PC

Useful

Repair IMEI
Solution of error 2020 and 4032 with firmware
Information on the 6735P and 6735M variety on this device
Activate the Navi bar
GApps cleaning
Dolby Atmos R6.5

Post has been editeddima101097 - 18.08.17, 14:27

Reason for editing: AOSP (Android Open Source Project)

[Linbov_Fly_IQ451]

Swedze,
My problem was solved) the output was this:
1 - downloaded the firmware from herehttp: //www.needrom.com...ogee-y100-pro-algeria/
2 - downloaded the driver and flashlight from hereDoogee Valencia 2 Y100 Pro - Discussion
3 - flashed with the "volume -" button pressed
4 - formatted via flashlight
5 - point 3 again
6 - on this point I decided to turn on the phone, but it did not turn on, but then began to respond to the inclusion of "turn + volume +" and that's it.
7 - flashed in the usual way
8 - there is no limit to joy
: happy:
Thank you all for your help: thank_you:

[dima101097]

Linbov_Fly_IQ451,
Strangely, I didn’t have the first device on the MTC and I didn’t pinch the buttons with the firmware, it was always enough to pull out the battery, prepare the flash unit and connect it to the PC, after which the phone was detected and the firmware was installed.
Well, well, that turned out to restore, and thanks for describing the process, maybe someone will come in handy

[vasiuta1]

dima101097,
How does the camera behave on cyan? Flash and grit?

[dima101097]

[email protected], 20:03

How does the camera behave on cyan? Flash and grit?

As in stock.
By the way, legolaiss wrote that when there was no patch to the camera and it did not work correctly, the flash when turned on became momentarily brighter and after it was as dull as on the drain, and I noticed this moment after myself, maybe soon we can think of something

[vasiuta1]

dima101097,
Good news, it means everything is probably fixable)!

[dima101097]

[email protected], 20:08

Good news, it means everything is probably fixable)!

I agree. The "problem" with the flash was corrected by replacing the files, so that if you picked up the flash from another device, you can fix the problem with a dim flash. But this is just a hunch.

[StupidSage]

In the topic of discussion, no one responded, maybe someone can help. Remove plz boot.img firmware from 12/29/2015.

[dima101097]

[email protected], 18:03

Remove plz boot.img firmware from 12/29/2015.

Hold onboot.img(6.42 MB)

[Linbov_Fly_IQ451]

How are you doing with cyan? Are there any successes?)

[dima101097]

Linbov_Fly_IQ451,There is already a cyan where only gps does not work and with video codecs is not very: D

Post has been editeddima101097 - 27.02.16, 16:55

[Linbov_Fly_IQ451]

dima101097,But in a post with firmware this is not written ... So I ask) does the mobile Internet work, and does the sound in order?) Well, does the mx player video reproduce the norms?)

[dima101097]

Linbov_Fly_IQ451,Mobile Internet works, sound, too, but I don’t know for mx, I didn’t set it, by Friday I'll post it, wait

[aleksander37]

Dima101097 @ 02.27.2016, 18:06

Linbov_Fly_IQ451,Mobile Internet works, sound, too, but I don’t know for mx, I didn’t set it, by Friday I'll post it, wait

I hope by the end of the week I finished the gps and video codecs)))
Ato cyan is much better than runoff. On the last phone it was him who used the excellent build. Ato stock in terms of design from Domzhe not quite ice))

[dima101097]

aleksander37,
Let's see, to be honest, I’ll probably lay out an assembly with gps problems and codecs and then let someone else do it, so far I have enough stock, and soon there will be a firmware umiOS already running, there are only a few proxy left

[StupidSage]

The firmware in the cap from 12/29/2015 is actually the very first r06 of July. Yesterday I downloaded and installed, I still had to roll 5 updates through the air. Swung with poison.

[dima101097]

Most likely this will be the most correct way to get a PTA (air) update after rutting.
Until the recent update, I had a root, a gravity side, and so they gave (this is not so important) because of what would be updated in two clicks did not work.

Using a PC:
1) Download the firmware for SP Flash Tools (link in the header)
2) Download custom recovery (there is a link in the header)
3) Install drivers and flash recovery
4) I booted into the recovery and cleaned up the system partition (SYSTEM only)
5) Open SP Flash Tools and select the scanner file (MT6735M_Android_scatter_y100_pro) in the folder with the firmware (the firmware needs to be unpacked
6) Uncheck all lines except System
7) Choose "Dowland only"
8) Click on "Dowland" and connect the disconnected device
9) We are waiting for the green circle after we distort / insert the battery and turn it on

Without PC help:(I did not check this, but in theory it should work perfectly)
1) Download the firmware for SP Flash Tools (link in the header)
2) From the archive, unpack the file system.img (preferably to the root of the memory card)
3) Download custom recovery (there is a link in the header)
4) Install the recovery throughRashr - Flash Tool(we need root rights)
5) I booted into the recovery and cleaned up the system partition (SYSTEM only)
6) Now in the recovery click install, and there will be something like "Install image" from below that we choose, then install system.img that was unpacked from the archive (I will not begin to paint it as it is intuitively clear)

After that, our System section becomes, as it were, untouched and the recovery should after some time become stock (we check it ourselves and if not, then flash it on the drain)
After such manipulations (it took about 10 minutes at most), I upgraded to the latest version without loss of personal files and applications on the internal memory.
I think it is worth mentioning that it is best to use TWRP 3.0 (you can find it in the header), but for the version without a PC, only TWRP 3.0 is needed

I do not bear any responsibility.

Post has been editeddima101097 - 01.03.16, 17:51

[Dealer1980]

Did someone do this?

[Swedze]

Dealer1980at least - the creator of this post

[dima101097]

Dealer1980
He made a method for the PC, which is why he described it, and the logical method for the recovery of working

[Valtor]

Peace for everyone!
Poke your finger where to get normal firewood under WIN 8.1 x64
A ruled device with a fool decided to update the air .... got a brick in the state of downloading applications.