6 pagesV  « < 2 3 4 5 6 > »  
 
REPLY
> TP-Link TD-W8961ND - Discussion | [adslmodem] [wifirouter]
alex @ rya
Message#1
08.02.17, 14:41
WiedЕєmin
*********
[offline]

Group: Curators
Messages 10009
Check in: 04.09.13
Xiaomi Redmi Note 3 Pro Prime

Reputation:-  3398  +

TP-Link TD-W8961ND - Discussion


A photo:
Attached Image

Attached Image

Description:
ADSL 2/2 + modem, wireless N access point and 4-port router in one device
IEEE 802.11n 300 Mbps wireless data transfer rate is ideal for applications that are sensitive to bandwidth or delays and signal interruptions, such as online gaming, IP telephony, and even high-definition streaming video
Easy Setup Assistant setup wizard with multi-language support allows you to quickly and easily configure the device
Easy installation of wireless protection with one touch of the WPS button and on / off wireless broadcasting by pressing the Wi-Fi On / Off button
Specifications:
Interface 4 ports 10/100 Mbit / s RJ45
1 RJ11 port
1 buttons on / off button power supply
1 WPS button
1 on / off button Wi-Fi
External power supply 9 VDC current / 0.85 A
IEEE IEEE 802.3, 802.3u standards
Standards ADSL Full-rate ANSI T1.413 Issue 2,
ITU-T G.992.1 (G.DMT),
ITU-T G.992.2 (G.Lite)
ITU-T G.994.1 (G.hs),
ITU-T G.995.1
ITU-T G.992.3 ADSL2 standards (G.dmt.bis),
ITU-T G.992.4 (G.lite.bis)
ADSL2 + ITU-T G.992.5 Standards
Dimensions (WxLxH) 195 x 130 x 35 mm
Antenna type Omnidirectional, removable, Reverse SMA
Antenna gain 2 x 5 dBi
PARAMETERS OF WIRELESS MODULE
Standards of wireless networks IEEE 802.11n, 802.11g, 802.11b
The frequency range (reception and transmission) 2400-2483.5 MHz
EIRP (Wireless Power)<20 dBm or<100 mW
Wireless network protection Supports 64/128-bit WEP encryption, WPA-PSK / WPA2-PSK, wireless MAC address filtering
Useful links:


There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the "Complaint" button under the messages to which you want to add links, or through QMS.

Post has been editedstp101 - 07.04.19, 13:07
Reason for editing: Alteration of W68961_v3>>W8968_v2 (USB-mod)
Mucha333
Message#62
19.11.18, 11:48
Old resident
*******
[online]

Group: Friendssavagemessiahzine.com
Messages 779
Check in: 11.10.13
Xiaomi Redmi Note 4 4/64

Reputation:-  10  +

Guys why can not I configure parental control on the td8968 modem? I want him to allow access to certain sites that I register in the settings, but instead he blocks all sites!
112233445
Message#63
21.11.18, 15:04
Local
*****
[online]

Group: Friendssavagemessiahzine.com
Messages 205
Check in: 09.04.13

Reputation:-  3  +

Became the owner of a Wi-Fi routerTD-W8961NIn principle, everything works well, there were no problems with the setting. And tell me how to configure the built-in VPN, is it real?
Rainman2004
Message#64
06.01.19, 22:07
...
******
[offline]

Group: Friendssavagemessiahzine.com
Messages 576
Check in: 13.03.08
teXet TM-4677

Reputation:-  41  +

MemchikKR @ 11/06/18, 00:13*
Hello. When I bought my Asus laptop

If you allow yourself financially, then buy yourself a router from the same office, and not this semi-trash ...
P.S. People on this forum, praising such rubbish, apparently did not use the routers of other manufacturers who do not know the problems of 5-7 years for ADSL.

Post has been editedRainman2004 - 06.01.19, 22:12
Alex-motoro
Message#65
07.01.19, 00:45
Novice
***
[offline]

Group: Active users
Messages 36
Check in: 16.04.12

Reputation:-  3  +

Rainman2004 @ 01/06/19 22:07*
P.S. People on this forum, praising such rubbish, apparently did not use routers from other manufacturers who do not know the problems of 5-7 years for ADSL


Why are you so sure that the filling of the routers is exactly the same as the ADSL modems from the ASUS company inside is superior to essentially the same stuffing from the same TP-LINK?
maksim8585
Message#66
17.01.19, 08:35
Visitor
**
[offline]

Group: Active users
Messages 25
Check in: 13.07.13

Reputation:-  0  +

Satellite Internet how can I set up?
_Knyazev_
Message#67
21.01.19, 09:25
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 163
Check in: 13.01.12
Microsoft Lumia 640 DS LTE

Reputation:-  28  +

I, as the owner of this router, will say that revision 1.00 of this router is so-so. After 2 years of good work, I simply started to blunt, the web interface almost does not open, and the LAN disconnects the connection. Apparently tired of working.
I looked at the microcircuit, order. Conders are not swollen, there is no damage on the board.
Riddle that could happen to him.
kola098
Message#68
20.02.19, 14:20
Visitor
**
[offline]

Group: Active users
Messages 21
Check in: 07.01.17

Reputation:-  0  +

TP-Link TD-W8961ND v3 firmware for 2016 can be rolled back to the firmware version earlier for example for 2015
Promix_01
Message#69
17.03.19, 17:22
User
****
[offline]

Group: Friendssavagemessiahzine.com
Messages 64
Check in: 22.08.12
Samsung Galaxy S7 EDGE SM-G935

Reputation:-  1  +

Good day to all. Tell me please, there is a TD-W8961N v3.0 router. The latest firmware from 07/02/2017. I started to blunt, namely losses in packages, for example, when pinging sites, packages 50 to 50 are accepted, delivered for repair, but did not reveal a defect in the service center, turned to the provider, they brought their router to check and everything works without problems, that is It is in this router that you can change the firmware to an older one, or can it be installed from some other device?
blonde at the piano
Message#70
18.03.19, 01:56
User
****
[offline]

Group: Friendssavagemessiahzine.com
Messages 52
Check in: 07.05.16
Nokia N9

Reputation:-  0  +

Promix_01 @ 03.17.19, 17:22*
they brought their router to check and everything works without problems, that is, it is in this router



A few days ago there was the same problem. Phoned those. support and a very polite boy just explained step by step how to put a tick. Everything works amazingly!
Qwert210101
Message#71
19.03.19, 10:27
a guest
*
[offline]

Group: Users
Messages 1
Check in: 04.03.19

Reputation:-  0  +

People, how on this miracle wi-fi bridge for huawei e8372h-153 modem to do?

Post has been editedQwert210101 - 19.03.19, 10:33
Reason for editing: 1. Not a complete description of the question. 2. I forgot to put the word to do.
palexxx
Message#72
19.03.19, 23:24
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 329
Check in: 25.01.13

Reputation:-  66  +

Considering that TD 8961 v3 is built on the popular Ralink RT63365E chipset and given the widespread death and death of ADSL (unlimited 3G is usually faster and cheaper), it can and can sometimes be changed into much more functional models on the same platform. The blessing with his "brothers" work has been going on for a long time, and volumes have been written.

The TD8961 will be firmware from the following devices:
- Huawei HG532s
- ZTE N108N v2.5
- TPlink TD8968
- Asus DSL N14u

All but ZTE in this list have USB support (3G / 4G modems, printers, scanners and portable USB drives). Asus N14u and TPlink 8968 havefull WAN port functionality (including automatic filer for missing cable connection using 3G / 4G) on one or any of the LANs, as well as WiFi repeater mode

Hardware TD 8961 v3 is solicited for soldering a non-soldered USB port (you need the connector itself, a 5V stabilizer for power and two jumpers). For smart firmware, you also need to replace the RAM plate with 32MB (ESMT M12L2561616A) or 64MB (K4S641632H-UC75), and replace the flash drive with 4, 8 or 16MB (for example Winbond W25Q32FVSIG). You can also solder the activity LED of the USB device unplugged from the factory.

In general, practical use will be very useful.experience of similar upgrade for ZTE H108N

Post has been editedpalexxx - 20.03.19, 11:37
palexxx
Message#73
20.03.19, 11:45
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 329
Check in: 25.01.13

Reputation:-  66  +

Qwert210101 @ 03/19/19, 09:27*
People, how on this miracle wi-fi bridge for huawei e8372h-153 modem to do?


In the firmware - no way. And wifi built in 8372 is not suitable for any serious tasks - it heats up and hangs. Solder the USB port and go to the Asus N14U firmware - there will be full speed, up to 16 connected devices and a bunch of other blinds. Admin Hilink'a by the way remains available through the router.

Price rework materials - two dollars. For a single rework, it may even be conditionally free because of the old DDR bar found among the trash))

PSIf here a friend donates TD 8961 for scientific purposes - I will make a report-guidance on revision with photo notes

Post has been editedpalexxx - 20.03.19, 11:46
Artemiusm
Message#74
23.03.19, 18:58
Experienced
******
[offline]

Group: Friendssavagemessiahzine.com
Messages 598
Check in: 25.09.13
Nokia N8

Reputation:-  16  +

Good evening! Need help experts, if there are any in this topic. In general, there is a TD-W8961ND revision v.3.1 router, the power-on, line and internet symptoms constantly turn on when the power is on, and 4 lanterns flash periodically although the router is not connected anywhere, of course there is no web interface, I don't know the background, I opened it through ttl it was normally stitched but not a good log has not changed, tell me where to dig
LOG
Attached Image

P.S. With the ATGR command, the router successfully loads and turns on and works even after 1 ~ 2 reboots, but then everything is new, it is obvious that the hardware error is, but so far it is not clear what elements are called, the flash is OK, since the router was completely flashed, I don’t know what to think ((

Post has been editedArtemiusm - 23.03.19, 21:19


--------------------
Never be afraid to do what you do not know how. Remember, the Ark was built by an amateur. Professionals built the Titanic.
haetrugo
Message#75
04.04.19, 20:32
a guest
*
[offline]

Group: Users
Messages 1
Check in: 17.01.13
Samsung Galaxy S3 GT-I9300

Reputation:-  0  +

* _Knyazev_,
Most likely, the port / s was punched by static. This leads to unstable operation of the router, including preventing it from entering the settings - there was a similar problem with asus, after resetting it allowed to climb in the settings for a while, then the problem recurred - solved by electronics repair, but it is cheaper and cheaper to buy new.
palexxx
Message#76
07.04.19, 12:39
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 329
Check in: 25.01.13

Reputation:-  66  +

Attached Image

So, the promised review of the redesign of TP-Link TD-W8961ND v3 into a useful and necessary device in the household.
Actually, on closer inspection of the board, it becomes clear that the TD-W8961 v3 isstripped down brother TD-W8968 v2with less RAM and ROM, and without USB. Restore justice and return its easy, than today and do.

To rework we need: ram plate (for exampleESMT M12L2561616A), 4/8/16MB EEPROM flash driveWinbond W25Q64BV(depending on the desired firmware), any 5V stabilizer for any current up to 500mA, vertical USB connector, electrolyte capacitor, resistors for 1k and 2k2, LED

Initially, the model 8961 has on board only 2MB of permanent memory and 16MB of operational memory. This explains the wretchedness of the firmware and functionality. The firmware shown below requires 32MB of RAM (ordesirableeven 64MB for Asus n14u) and 4MB flash drives (Huawei HG532 firmware), 8MB (firmware from the related TD-W8968) or 16MB (Asus DSL N14U)

Any chip in a similar package and with the same organization of the address space will be suitable for replacing the RAM. My choice of ESMT M12L2561616A is due only to their use in my other serial alteration and accessibility for me. I strongly advise RAM to buy on Ali, there it will cost about a dollar

To replace the ROM, microcircuits in the SOP8 or SOP16 package with 3.3V power supply are suitable, I use Winbond W25Q32BV (Winbond W25Q64BV or Winbond W25Q128BV).

============================================
1. hardware alteration
1.1 RAM.
1.1.1 Memory Chip

You can replace the RAM without a hairdryer. To do this, carefully cut off the legs of the old dies with a stationery knife (from the chip, not from the board !!!), remove the remains of the legs with a soldering iron, qualitatively solder the new chip. Note, the RAM chip is very sensitive to poor soldering and leakage, do not be lazy to wash the flux.
Replacing RAM
Attached Image
Attached Image
Attached Image

1.1.2 Strap resistors
Strap resistors set the memory controller (its functions are assigned to the adsl chip of the RT63087N modem) how much memory is on board. Without their soldering, the device will not see more than 16MB. They are located near the RT63087N. Indicated by R40 and R38. If not one of them is unsoldered, the device sees 16MB of RAM. Only R40 is decoupled - sees 32MB, both R38 and R40 are decoupled - will see 64MB. Strap resistors should be 1kOhm
strap location
Attached Image

1.2 Flash Drive-EEPROM-ROM
Everything is prosaic, flashing the selected dump with the programmer and soldering the flash drive instead of the standard one. The board has wiring for octopuses and for 16-foot chips.
flash drive ROM case SOP8
Attached Image

1.3 USB
This section can be omitted if you do not need it. But as for me - USB is the most delicious part, because You can organize a fault-tolerant 3G Internet channel in case of cable failure or use the printer via WiFi. By the way, the hub splitter device also supports, so you can use both a printer and a 3G / 4G modem at the same time.
1.3.1 Jumpers over USB D + D- tires
Jumpers need to put on the way to the processor two pairs. One is obvious - and indicated on the F1 board, the second is closer to the process, I generally hid under sealant, keep the throttle, - marked R47 and R48
D + D- jumpers
Attached Image

1.3.2 Power 5V for USB.
There are three possible ways, each has its own pros and cons. You can restore the standard DC-DC converter on the board, you can take ready-made 5V from the stabilizer for the analog part of the adsl modem (actually, if you are going to de-energize it, for example, it heats up after a thunderstorm) and just an external separate stabilizer next to the board. I went the last way, because I had an honest stabilizer 7805 in the TO-220 package and an improvised radiator for it. Supply points 5B and GND- are convenient and provided. In addition, I took a regular place under the electrolyte and threw a couple of jumpers to use it - FB4 and R19
5V USB Power Stabilizer
Attached Image

1.3.3 USB connector
You need a standard vertical connector, apparently it happens only in one direction - you will not mix it up. In the case you need to cut through the window 8 * 16mm, it is convenient to do it with a drill for 7mm - 2 holes, then a stationery knife and file. It turns out indistinguishable from the factory :)
USB connector and window
Attached Image
Attached Image
Attached Image
Attached Image

1.3.4 USB Activity LED
Please note that it will work out of the box only in the TD-W8968 firmware. We putnecessarily blueLED, do not confuse the polarity - and quenching resistor R77. For the performance of the USB_Act and Internet LEDs in the HG532s and Asus DSL N14U firmware, a minor revision is required. The fact is that with these devices the corresponding GPIOs are assigned to other legs. It is necessary to hang the jumpers between the corresponding pins of the wifi chip Ralink RT5392L.
Gpio LED location
Attached Image
--------- TD-W8961 / 68 ------- ASUS N14U / Huawei -
USB ----------- 19 --------------------------- 46 --------- -----
Internet ------ 43 -------------------------- 45 --------------- -

In simple words.Redoing 8961 in Asus n14u need to put 2 jumpers on Ralink RT5392L: 19-46 and 43-45

Actually on this with hardware modifications - everything, a few words about the firmware
===================================================
2. Firmware dumps, filled with programmeror via UARTLike this?
Our device is assembled on a similar platform with a dozen interesting devices. Therefore, it can and should sometimes be turned into a device from another manufacturer. Suitable firmware and briefly about them:

but)Huawei HG532s.
Attached fileHG532s_tuned.rar(3.75 MB)
Login to admin admin / @ Hua1234 192.168.1.1 The default WiFi password can be peeped by connecting via WPS
Requires 4MB flash drive
It can work with 3G modems, there is a print server, there is support for file storage (flash drive or portable HDD). Wifi repeater mode is not, cable WAN is also not (although you can flash it with Chinese firmware and WAN will appear).

b)TP-link TD-W8968
Attached fileW8968 v2.0_140514_tuned.rar(6.11 MB)
Login / password admin / admin 192.168.1.1
8MB flash drive required
It can work with 3G modems, there is a print server, there is support for file storage (flash drive or portable HDD). There is a regular cable WAN on LAN1, there is a WDS (read the WiFi repeater). The menu language is English only.

at)Asus DSL N14U
Attached fileDump_FW_DSL_N14U_1123617_2018.12.10_25Q128.rar(15.21 MB)
Login / password admin / admin 192.168.1.1
16MB flash drive required
The fattest machine of the above. It can work with 3G and 4G modems, there is a print server, there is support for file storage FTP and SAMBA (flash drive or portable HDD). There is a WiFi client mode and a repeater. WAN can be assigned to any of the LAN ports. In addition, there is an automatic DualWAN - switches to the backup 3G channel in the event of a cable Internet failure. The menu is Russian, there is SSH and telnet
IMPORTANT. The Asus DSL N14U's reset button is on the other foot of the processor - on the 34th. Therefore, I strongly advise you to supply 3.3V power to this 34 foot through a pull-up 1kOhm. Otherwise, the router may unpredictably load into the emergency recovery mode of the firmware.Original source

The list of supported models of 3G and 4G modems can besee here(updated)

Post has been editedpalexxx - 15.05.19, 10:07
ahssv
Message#77
08.04.19, 20:38
Visitor
**
[offline]

Group: Users
Messages 12
Check in: 20.04.12

Reputation:-  0  +

palexxx please tell me how to make TD-W8968 v.3 out of TP-Link TD-W8961ND v.3.1, v.3 you need v.3 for it to have openwrt. thank
ahssv
Message#78
08.04.19, 21:08
Visitor
**
[offline]

Group: Users
Messages 12
Check in: 20.04.12

Reputation:-  0  +

I have 8961ND3.1 and it is not on the list
ahssv
Message#79
08.04.19, 21:19
Visitor
**
[offline]

Group: Users
Messages 12
Check in: 20.04.12

Reputation:-  0  +

maybe I didn’t explain the problem for TP-Link TD-W8961ND v.3.x not by openwrt (I have this model)
for TD-W8968 v.3 there is openwrt software, but palexxx describes a remake from v.2 I think there are changes on the hardware, so I ask for clarification.
palexxx
Message#80
08.04.19, 21:25
Local
*****
[offline]

Group: Friendssavagemessiahzine.com
Messages 329
Check in: 25.01.13

Reputation:-  66  +

ahssv @ 04/08/19, 19:38*
palexxx please tell me how to make TD-W8968 v.3 out of TP-Link TD-W8961ND v.3.1, v.3 you need v.3 for it to have openwrt. thank

TP-Link TD-W8961ND v.3.1 corresponds exactly to TD-W8968 v.2

TD-W8968 v.2 in v3 can not be redone in principle. Completely different iron. Other platform

Openwrt for TD-W8968 v.2 is not and is not expected, because the ancient trash for the Papuans (for us :))
anvarberg
Message#81
08.04.19, 23:32
Experienced
******
[offline]

Group: Friendssavagemessiahzine.com
Messages 595
Check in: 04.08.12
Blackberry priv

Reputation:-  5  +

How to catch singal on this router and fart further?

6 pagesV  « < 2 3 4 5 6 > » 


 mobile version    Now: 06/18/19, 18:11