Xiaomi Roidmi - Discussion | Other
Karpo518 , during the signal, look in the program, perhaps the roadmi indicates a low battery. Posted on 03/09/2019, 10:24 PM:
real808 , try connecting the roidmi first, and then the mibend. It was such that due to the connection to the clock it did not connect to the romeI will supplement the list of cars for 3S:
- Toyota RAV4 (XA20) 2004, works
- Lexus RX300 II generation, works
- Toyota RAV4 (XA20) 2004, works
- Lexus RX300 II generation, works
Karpo518 @ 03/09/19, 10:33 PM
Tell me, what kind of nasty double signal sometimes interrupts playback? How to deal with it?
there is a recharge or undercharging in your car, run the application, everything will be visible there, the signal can be turned off there
I observe a problem with 3S
When the ignition is turned on, the device turns on with noise and interference. But if you remove it from the cigarette lighter and reinsert it, a perfectly crystal clear wave is turned on. At the maximum volume of the radio, there are no rustles even.
How to overcome interference? Zadolbalo pulling it here every time it starts.
When the ignition is turned on, the device turns on with noise and interference. But if you remove it from the cigarette lighter and reinsert it, a perfectly crystal clear wave is turned on. At the maximum volume of the radio, there are no rustles even.
How to overcome interference? Zadolbalo pulling it here every time it starts.
Complementing the 2006 Ford Fusion.
Roidmi 3s interferes with the standard control of the central lock.
And since there is always voltage in the cigarette lighter in a car, there is a chance that there will be problems with locking or unlocking the doors.
Roidmi 3s interferes with the standard control of the central lock.
And since there is always voltage in the cigarette lighter in a car, there is a chance that there will be problems with locking or unlocking the doors.
I bought a year ago Roidmi 3S, inserted it into the cigarette lighter socket of an Opel Vectra C ... A day later I noticed that some electrics weren’t working - a fuse flew out ... The idea of ​​modernization arose immediately, but lasted for a year :): With tape or tape I did not want to collective farm.
In short, I took a heat-shrink tube, cut a piece measuring 1.5-2 cm, put it on the bottom, warmed it with a lighter and it turned out to be almost a factory mode ... :)
In short, I took a heat-shrink tube, cut a piece measuring 1.5-2 cm, put it on the bottom, warmed it with a lighter and it turned out to be almost a factory mode ... :)
 |
 |
 |
I wonder how much the device consumes when it is constantly inserted into the cigarette lighter? Will the battery drop? There are also problems that the device interferes with the remaining channels of the radio, and it itself occasionally plays with noise.
[email protected], 14:32
I bought a year ago Roidmi 3S, inserted it into the cigarette lighter socket of an Opel Vectra C ... A day later I noticed that some electrics weren’t working - a fuse flew out ... The idea of ​​modernization arose immediately, but lasted for a year :): With tape or tape I did not want to collective farm.
In short, he took a heat shrink tube, cut a piece measuring 1.5-2 cm, put it on the bottom, warmed it with a lighter and it turned out to be almost a factory model ...
In short, he took a heat shrink tube, cut a piece measuring 1.5-2 cm, put it on the bottom, warmed it with a lighter and it turned out to be almost a factory model ...
I understand that the metal tip that comes with the "+" contact must be insulated for connectors that are ground under the cigarette lighter. At Astra G itself, I recently bought a Xiaomi 70mai Dash Cam Pro registrar, so there the charger has a plastic tip and sits very well, which is why I paid attention to this device. I thought I could do with a splitter, but they hang out with a spring "-" contact. As a result, I came to the conclusion that a "socket" with round contacts is necessary, according to the type as in the figure. Maybe in future versions the tip will also be plastic
Attached images
 |
 |
DevianTT @ 03/18/19, 10:55
As a result, I came to the conclusion that a "socket" with round contacts is necessary, according to the type as in the figure. Maybe in future versions the tip will also be plastic
Yes, it’s because of the iron tip that it closes ... I don’t know how it was possible to come up with such garbage ...
benefit84 @ 03/08/19, 13:52
Most likely the frequency is not very good, try others
I think that it makes no sense to do this.
alex4232, usually there is some kind of noise only at maximum volume, below 85% all the rules .. about repair, yes, hardly)
romka0017 , Oh ... Monsieur sees the fundamental difference between "frequency modulation" and "frequency modulation" ??? : blink:
©savagemessiahzine.com2005-2019. All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement