[X]Assistant

[kumarai]

Discussion of the hardware of the Head Devices running on the RK3066 / 3188 processors. MCU - IAP15L2K61S2.

MCU Versions: MTCB-KGL, KLD, GS, RM, JY, KYD, MX, BN, NA.

Discussion пїЅпїЅпїЅ | Discussion RK3066 / RK3188 | Hardware | Modification of software and decorations |

• To compare the device with competitors and on the choice of devices, please contact: Selection and Comparison
  
• Before posting photos, read the topic Working with Images on the forum
  
• Messages that are not related to the topic of discussion (offtopic) are deleted without warning.

FORUM RULES MUST KNOW EVERYTHING!

Specifications

CPU:RockChip RK3066 / 3188
Graphics coprocessor:Mali-400MP4
RAM:DDR3 1 GB
Microcontroller "MCU":STC15F2K60S2
Bluetooth module:STR BC6130
Audio codec:WM8731S
Video decoding controller"10-bit analog-to-digital converter": T132BT, analog ADV7181D
Video Switch:FMS6502
Sound processor:ROHM BD3702FV, BD375 ** FV
WiFi adapter:IEEE802.11b / g / n, Realtek RTL8188CTV
GPS receiver:u-blox 7 GNSS, UBX-G7020
USB2.0 HUB Controller:ALCOR AU6258
AM / FM radio tuner:TEF6624, TEF6686, TDA7706, TDA7786, (SI4754 / 55 not supported by MCU)
Capacitive touch controller (touch screen): GT801, GT911

FAQ

AT:

пїЅпїЅ пїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅ, пїЅпїЅпїЅпїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ пїЅпїЅ RGB пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ пїЅ пїЅпїЅпїЅпїЅпїЅ RGB пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ пїЅпїЅпїЅпїЅпїЅпїЅ? download

Oh no! There is no hardware ability to install them there.

AT:Made direct sound control from7floorThere is no sound from the radio, and what should I do?
A: Replace the resistors in the I2C bus Audio codec WM8731S.

AT:When finalizing7floorcan solder resistors in wires?
A: Yes, you can solder the wires.

AT:Is it enough to solder three wires (black, green, white) for USB OTG firmware? What to do withred (+ 5V)wire?
A: It is necessary to connect to U2 C17 (KLD board) otherwise the hardware will not work out the switch.

AT:How to connect, run the radio at home?
Рћ: To the stabilized power supply 12V 60W (5A (+/- 3A)) connect:
ACC (red, red) and BAT (yellowy, yellow) to plus 12V.
GND (black, black) to minus 12V.

Documentation

Datashit RK3066 -RK3066_datasheet.pdf(851.58 KB)

Datash MCU -STC15F2K60S2-english.pdf(10.12 MB)

Bluetooth BC6130 datasheet -BC 6130.pdf(4.22 MB)

Datashit Audio codec WM8731 -WM8731.pdf(762.15 KB)

Datashit Video Decoding Controller T132BT, analog ADV7181D -ADV7181D.pdf(386.92 KB)

Datasheet Video switch FMS6502 -FMS6502.pdf(547.75 KB)

Datasheet Sound Processor BD37534fv -bd37531fv-e.pdf(936.82 KB)

Datashit WiFi-adapter RTL8188CTV -RTL8188CTV.pdf(518.24 KB)

Datashit GPS receiver UBX-G7020 -UBX-G7020.pdf(1.11 MB)

USB2.0 HUB Controller datasheet -AU 6258.pdf(363.56 KB)

Datashit FM Tuner TDA7706 -TDA 7706.pdf(309.36 KB)

Datashit FM Tuner TDA7786 -TDA7786_datasheet.pdf(913.61 KB)

Datashit FM tuner TEF6624 -TEF6624.pdf(2.06 MB)

Datasheet Capacitive touch controller (touch screen) GT911 -GT911.pdf(1.56 MB)

Data DC-DC Converter M2303 -MP2303A_r1.1.pdf(436 KB)

Datashit display 800x480 -HSD070IDW1.pdf(416.26 KB)

Datashit display 1024x600 -HannStar-8-HSD080IFW1-A00-1024-600-600-NITS.pdf(1.02 MB)

Compatibility

For simultaneous receptiongps / glonasscompatible 8th u-blox modules:NEO-M8N(instructions for soldering in development)
Compatible terminal amplifiers -PAL007, TDA7560, TDA7850

Software and hardware developments

Direct sound processor controlROHM BD37 *** FVfrom7floor:пїЅWe study here
MCU Reverse Engineering EngineeringMtcmcutool- utility for manipulating MCU firmware fromDark simpson: We study here
Modified MCUs fromdarkleo: hereandhere

Hardware improvements

Increase RAM (RAM) up to 2 Gb -here
Replacing USB hub AU6528 to GL850G -Read here
Replacing the sound path FM tuner -Read here
Replacing the input circuit FM tuner TEF6624 -Read here
USB OTG RK3066 / 3188 -Read here
Eliminate display flicker, add contrast -hereandhere
There was a bad connection through the bluetooth, they did not hear me, they said that I was speaking as if from a dungeon "for GU KYD" -here
Instructions for connecting an external microphone to the Bluetooth module: -here
Hardware on / off button (entry and movement through points of recovery) -here

Experience exchange

USB Audio Getting Started Guide -here
Allowance for connecting head units to the vehicle electrical system -here
The connection between the onboard computer Multitronics MPC-800 -here
I measured by clicking on the left twist, thereby sending the GU in a dream. I did not turn off the ACC. Current measure on the yellow wire (BAT). -here
Instructions for connecting a third-party DVB-T2 TV tuner to the GU for touch-screen control -here

Interesting

Auto sound problem solving -link

Remember:
Everything you do - you do at your own peril and risk!
The authors of the modifications and the Administration of the forum is not responsible for the performance of your devices!

Topics Curator: kumarai

Post has been editedkumarai - 05.01.17, 22:25

Reason for editing: Datashit FM tuner TDA7786

[navy007]

Instructions for connecting an external microphone to the Bluetooth module:
! We buy a connector and a 3.5mm plug

, a good electret microphone (for example, Panasonic wm61), but any handy handy one can be, the sensitivity will be worse

, the screened microphone cable - which one will also like it, there is not much difference (only not coaxial for the antenna).
Regardless of whether you have a jack for connecting an external microphone, or not, in any case, a direct connection will save you from a lot of noise.
1) We are looking for the jumper "C32" with the number "0" on the board next to the module bt and unsolder (this is just a short one for connecting the microphone from the motherboard to the bluetooth board)

If you do not have this, pay attention to the back side of the Bluetooth card - all legs are signed there.
There are 2 options to disconnect the board - unsolder the jumper or cut off the leg, which is soldered to the board from the contact "mic"
2) Install the Jack F 3,5mm connector - it fits perfectly into any of the pair of empty holes in the back wall (or you can drill a new one)
3) Connect any socket with shielded cable directly to the bluetooth module - braid on any contact "GRND", central wire to contact "MIC"

5) Solder the cable of the required length to the microphone with a Jack M 3,5 plug (tip +, ring-)
6) Place the microphone as close to the head as possible (to the central ceiling, to the side stand — to your choice)
As a result, the built-in microphone works with android, and external with bluetooth.
The sound quality also directly depends on the BT module. With such a soldering we just remove the extra links in the chain.
Attention!There is always the possibility that your GU is not arranged, check whether everything is ringing on those feet-contacts that are indicated in the recommendations!

Post has been editedkumarai - 25.04.16, 23:44

[kumarai]

Badboy2 @ 12.02.2015, 22:22

What else can you try?

Only for those who have the on / off button is not hardware but software = Opel / Chevrolet,
also for radio with buttons on the touchscreen

1. disassemble the DVD unit
2. solder two wiring (red nicks)

3. on the other end of the wire the button is constantly open, when pressed it closes (button in the glove compartment)
4. we collect the radio tape recorder
5. key in the ACC position
6. expect full download
7. we clamp the withdrawn button and without releasing we press reset, release the button in three seconds
8. waiting for download recovery
- pressing the button once will allow you to navigate through the recovery points, a long press confirms the choice of the selected item
ps GM brains also allow you to turn on the radio without a key for 30 minutes. then turn off before re-pressing. For this you need to disconnect the ACC wire from the KAN decoder and connect it to the common connecting deck.

Post has been editedkumarai - 26.08.15, 22:17

[harym]

As promised, I post a brief instruction on how to connect a DVB-T2 tuner to a PG for control from a touchscreen. The remote control of the tuner can work simultaneously. Work video -HERE

Attached files

Connecting a DVB-T2 tuner to GU.rar(3.68 MB)


Post has been editedharym - 12.05.15, 18:47

[kumarai]

Continuing the theme of glonass
It turned out why the EC-3670 module does not save the conf. there is a problem = (to save, you need a power supply. A good battery will last for 5-7 years
disconnect the circuit and put the battery, you need to unsolder one resistor on the board. according to the scheme I think it is clear where to solder.

initial config of the module

remove the checkmarks and set it in front of GLONASS

press the keysend
if the battery is present, the config will be saved
From the window, it sees the satellites glonass (of course, if there is an antennaGLONASS)

TTL wart 3.3 volts
prog -u-centersetup_v8.17.zip(15.35 MB)

I think the other day I will order u-blox M8 for GPS and GLONASS reception at the same time.

Post has been editedkumarai - 23.07.15, 00:21

[7floor]

Direct control of the sound processor for Android 4.4.4 and 5.1.1

Detailed instructions with pictures

purpose
The sound processor installed on our devices, and this ROHM BD37534FV and analogs, including the frequently-encountered BD3702FV, has the following functions:
• Three-band parametric equalizer with gain control within -20dB - + 20dB, frequency and Q-factor of the filter in each band.
• Adjustable loudness unit with gain from 0dB to + 20dB, with setting of filter frequency and high frequency suppression level.
• Subwoofer output settings, including the choice of signal source, cut-off frequency, phase, and channel gain.
In the standard implementation, all of the above is not taken into account and is not supported:
• Instead of a 3-band parametric equalizer, an externally 9-band graphic, with very strange logic of operation, is bolted - each of 3 groups of 3 bands adjusts one processor band, averaging its values. Apparently, a child of Chinese marketing.
• Loudness is not made using the built-in hardware unit, but by simply raising the low and high frequencies, which is far from the same.
• Subwoofer settings are fixed and not configurable.
In addition, in the standard implementation, the equalizer settings apply to any input, be it a system, radio, DVD, etc. Experience suggests that it is desirable to have separate equalizer settings for different inputs - the sound from the radio, for example, often wants to be corrected in a completely different way than when listening to music from files or a CD.

Description
Refinement consists of hardware modification and software.
The hardware modification consists in switching the I2C bus, which controls the sound processor, from the MCU to the Android board.
The software modification is divided into two parts - the system patch and the user equalizer application.
The system patch consists of a module for the Xposed Framework, and two files - a library that allows you to call Linux functions from Android and a device driver to control the I2C bus.
The user application allows you to conveniently manage all of this - it is an equalizer, balance and settings.

Hardware modification
It is necessary to switch the control bus of the I2C sound processor, as shown in the diagram:

^{Figure 1, hardware modification scheme}

The printed circuit boards of different devices are different, so it’s impossible to give general instructions. The general rule is this: to find on the board the sound processor itself and the chip-sound codec WM8731, and to call resistors from their respective pins. Well, then in the circumstances.
Below is a photo of how it looks in the Joying head unit on the RK3188 and the screen 1024x600, the version for Volkswagen. The photos were taken somewhat messy, so the resistors, that is, no, but everything is marked on the images.

<sup>Figure 2, sound processor, resistors soldered


Figure 3, soldering wires to the resistors on the sound processor side


Figure 4, from the side of the Android board and the WM8731 sound codec</sup>

Software patch
Copy the file libjnidispatch.so to the / system / lib directory and set permissions to 644.
Check if there are i2c-0 ... i2c-4 files in the / dev directory, if not, then copy the i2c-dev.ko file to the / system / lib / modules directory and set the permissions 644; if the i2c-0 files ... i2c-4 is already there, then you don’t need to do anything - it means that the I2C bus driver is already compiled into the kernel. According to observations, in the firmware for the RK3066 there is no driver in the kernel and it is necessary to copy it, but in the firmware for RK3188 the driver is already in the kernel.
Next you need to install MTCCSC.apk - this is the module for the Xposed Framework - and activate it in Xposed itself.
Now you need to reboot. After the reboot, go to the Xposed Installer, Modules, find the MTC Custom Sound Control, click on it, and it displays the status. If everything went well, we will see this (channel may change, but, as a rule, it is equal to 4 at RK3188 and 0 at RK3066):

^{Figure 5, status check, success}

If something went wrong, we will see the following:

^{Figure 6, status check, error}

If there are errors, then it makes no sense to continue; you must first succeed.
Status can be one of the following:
• No patch detected - either the MTCCSC module is not activated, or the device has not yet rebooted after installation.
• mcu, No device driver i2c-dev - means that on a device that requires the i2c-dev.ko driver, it was not copied to / system / lib / modules, or a problem with access rights.
• mcu, Exception com / sevenfloor / mtccsc / I2cBus $ CLib - indicates the absence of the library file libjnidispatch.so or problems with access rights to this file.
• No access to / dev / i2c- ?;<additional error text>- despite the presence of a driver, it is impossible to get programmatic access to the i2c bus through driver files. Normally this should not happen, and if it happens, you need to contact the author for further proceedings.
• mcu, Error in write () 11 (no response from i2c slave) - program bus access works, but the sound processor on the bus is not detected - it is necessary to check the soldering, somewhere something was done wrong.
• mcu, Error in write () 110 (no response from i2c slave) - the same.
• i2c, Channel x (x-number) - everything works correctly
• MTC Sound status: mcu, i2c device files; Error, root access issue - solution: Going — SuperSU — settings — Enable SU during download — tick, reboot, check

Equalizer app
After installing the software patch and if you have a successful status, you can install SoundControl.apk - this is the equalizer. During installation, it is automatically integrated with the system, i.e. It will be launched instead of the regular one from the settings and from the notification curtain.
If you install it without first achieving success with the patch, then at startup you will see the following:

^{Figure 7, EQ after launch, if there are problems with the patch}

If everything is normal, we get:

^{Figure 8, the equalizer panel}

Left vertical navigation bar with three items: equalizer, balance and settings.

EQ mode
These settings are applied and saved separately for each input (System, Radio, TV, DVD, etc.)
Gain - the level of pre-amplification, that can be configured in the factory settings with a reboot. Here is derived for operational regulation on the go. Why do you need - different inputs initially have or may have a different signal level. To switch between the radio and the system or, for example, a linear input, the volume does not jump at the same position of the main volume control, this control is used. Plus, many are not satisfied with too low sound at the maximum position of the main volume - you can raise it here.
Low / Medium / High - three bands of hardware equalizer. Adjustable gain level from -20dB to + 20dB, frequency and quality of the filter. To understand these settings, it is worth getting acquainted with the principle of operation of the parametric equalizer, everything is easily searched on the Internet. In a nutshell, we change the signal level at a frequency, while the level changes in a certain range around. The smaller the Q, the more widespread the frequency range the adjustment extends, and the larger the Q, the narrower the width of the affected frequency band.
Loudness can also be read on Wikipedia, in short, it is a non-linear, volume-dependent distortion of the frequency response for a more equal perception of sound at different volume levels. In general, the adjustment lowers the level at the selected frequency. Also, the high frequencies by the HiCut parameter are slightly muffled - the smaller, the less this happens, the more - the stronger. Below is a graphic illustration of the chip manufacturer, how it works.

^{Figure 9, loudness operation}

In general, the sound will still have to tune by ear пЃЉ
On the right are buttons that show the current status and allow you to turn on or off the equalizer, loudness and silence mode (mute). That is, the equalizer and loudness is not enough to adjust, they still need to be turned on. Made to be able to temporarily turn off without knocking down the settings, otherwise you would have to move everything by zeros, and then restore it.
And in the upper right corner there is an inscription-indicator of the current active input (System, Radio, etc.), just for information.

Balance mode

^{Figure 10, balance mode}

Everything is clear, visually represented salon from Toyota Land Cruiser Prado, for your comfort, the circle can still be dragged with a finger and moved with buttons. Reset - return exactly to the center.

Settings Mode

^{Figure 11, Settings Mode}

Here you can customize the subwoofer and volume control range.
The output of the subwoofer in our devices can take a signal from the front channels, from the rear channels, and from a specially designed channel with a low pass filter. If a subwoofer is connected to the front or rear, the entire frequency range will be fed to it. If the input from the low-pass filter is selected, then the settings for the cut-off frequency (can be turned off to supply the full range), phase (0 or 180 degrees) and the gain level take effect.
Volume settings allow you to adjust the volume control to your equipment or desire. The minimum level is when the system controller is at the minimum, the maximum level is when it is at the maximum. According to the manufacturer, when adjusting the volume above 0dB, the noise increases significantly, so I would probably advise not to exceed this level, but it is better to raise the level of pre-amplification (the first knob in the equalizer).

Instructions in Word DOCX format:Readme.docx.zip(2.17 MB)

Files

libjnidispatch.so.zip(38.92 KB)

i2c-dev.ko.zip(4.7 KB)

Package:Xposed plugin repository -com.sevenfloor.mtcsound

In a personal periodically, there are requests to help deal with the piping on a particular PG.
People, I would gladly, with free time, would help, but there’s more.
I did everything on my device and, besides him, I did not see any others live.
It is also difficult to tell from the photos, you need to ring the tester, but what about the photo?
I repeat from the instructions: we are looking for a sound processor and a sound codec - these are two microcircuits that serve as starting points for searches.
Then from each, from the corresponding legs (on the diagram there is) we begin to ring the neighborhood. Somewhere tester yes squeals.

And, probably, if you still have questions, it is more correct to discuss them in the subject publicly: first, there are people who have seen many different devices - it’s more likely that they will help you, and second, a hint to someone, perhaps , will remove questions from others. The forum is the same.

comment

question:Personally, I would be very interested (and many people using several navigators and some kind of "arrow" to the heap for sure too) to have constant mixing of the android channel, regardless of the selected source. As I understand it, the sound from the android to the sound processor comes in parallel to its own individual channel, as well as to the MIX channel. Thus, as I imagine, with the selected channel, Android needs to jam MIX, and for any other selected channel, set the MIX level to maximum. And if in the interface you also finish the MIX channel level control engine, there will be fantastic in general.

Answer from 7floor:
The goal was to achieve approximately the same final volume level from Android as it passes through both the main stereo input and the mono mix.
The level of navigation mixing at the same time can be set to +10 if desired, and the navigator will be quite well heard.

Signal paths, according to the data sheet, with an indication of the available amplifiers:

Any of the normal inputs:
Input Gain 0 dB .. +20 dB - adjustable
Volume -79 dB .. +15 dB - adjustable
Fader -79 dB .. +15 dB - normally 0, may decrease through channels for balance

Mono mix:
Attenuator -79 dB .. +7 dB

Based on the assumption that the signal level from the Android input mono mix is ​​approximately equal to that on the corresponding stereo input,
Considering the blocks described above, the formula used to set the mono mix level is:

Mono Mix = Input Input System Volume + Volume

Faders are not taken into account, because Normally, it is zero by balance / fader in the center.
And, of course, the result for a mono mix is ​​limited to within the range of -79 dB. +7 dB
After all, according to the formula, it is theoretically possible to obtain a maximum of +20 dB + 15 dB = +35 dB, which is clearly beyond the range of possible values ​​for the mono mix.

Examples

Let it be established that the radio plays louder than Android by about 5 dB due to different levels from the codec and from the radio tuner.
Then, in order to make it comfortable to switch between radio and media (so that the volume does not jump), we set the adjusted Input Gain levels:
Radio Input Gain = +10 dB
System Input Gain = +15 dB
(there could be 0 and +5 with the same success)

Let the volume be set to some -20 dB (there the Chinese muddied a non-linear scale, it is more accurate to count laziness, but approximately in the middle of the scale "in parrots").
Listen to the player (input system).
The final volume will be +15 + (-20) = -5 dB
Switch to radio (radio input)
The final volume will be +10 + (-20) = -10 dB - that is, 5 dB quieter than the system, which compensates for the initially louder radio.
At the same time, the system is connected to a mono mix with a level of +15 + (-20) = -5 dB - which gives the output about the same volume level.

Turn the volume knob here and there - only the loudness component changes (-20 dB in the examples above),
those. the ratio of the active input levels to the mono mix does not change and remains equal to 5 dB, which always equally compensates for the difference in the levels of the codec and radio module.

It breaks down only when we turn the volume up to maximum, then in the sum with Input Gain it will come out for the acceptable +7 dB for the mono mix and it will sound quieter relative to the active input.
But at such volume levels, I personally do not listen to the navigator, this is for the rather for body massage with a subwoofer, and not for trips to unfamiliar places.

From more details.
Mono mix is ​​always connected, except when the phone is active (incoming call, outgoing call, conversation) or sys is active, or gsm_bt is active (this is for a bluetooth A2DP player in the Bluetooth application, hardware is the same sound processor input as the system ).

Probably, you can make a setting like mono-mix boost with a slider on which 0 .. + 10 dB, so that this value is also added to the above formula. For all sorts of protein there shooter and other things that are not set as the default navigator.
However, this does not help them to sound louder than the media player, well, no matter how. So does it make sense if on the road (as for me) you still listen to music more often than the defective radio?

Good luck! :)

Connection direct sound processor control

Connection direct sound processor control

MCU KLD

• connection fromlieutenant - Read here
  
• connection frombes90 - Read here
  
• connection fromFanis70 - Read here
  
  MCU ON
  
• connection fromsergey6767 - Read here
  
• connection from_Alexxx08_ - Read here
  
  MCU GS
  
• connection fromAlgur - Read here
  
  MCU KGL
  
• connection fromhn84board KGL A90 - V06.1 -Read here
  
• connection fromkumaraimotherboard KGL-MAIN-90D -Read here
  
  MCU JY
  
• connection fromserega1505 - Read here
  
  MCU KYD
  
• connection fromDaggers - Read here
  

Post has been editedkumarai - 14.10.16, 01:41

Reason for editing: data update

[SuperKungFu]

Bomb! : clap:
Does it depend on the version of the android?

[7floor]

SuperKungFu @ 10/11/2015 00:18

Does it depend on the version of the android?

Well, this is only for the device family in the header, there is one version - 4.4 KitKat
Hmmm, like, the ones that were on RK3066 on 4.2 JellyBean - no idea here.
I do not have other devices, try, say.

Post has been edited7floor - 11.10.15, 00:25

[SuperKungFu]

7floor @ 10.10.2015, 22:21

Well, this is only for the device family in the header, there is one version - 4.4 KitKat

I inaccurately expressed from the build.
In one of your messages it was previously written that it was made for a specific build

[7floor]

SuperKungFu,
It was before, there was a patched system framework.jar file
Now this is a module to Xposed, it is universal.

[lieutenant]

And so the revision from7floormade by KLD
Software affairs according to the author’s instructions, I’ll dwell on the hardware in more detail and with a photo
View of the processor (Android) board before rework

View of the main board of the state before the alteration

Android board with soldered I2C control bus

Main board with soldered resistors R70, R71

Main board with soldered resistors, but with MCU control off

GU board with soldered I2C bus

Now attention !!!
It is not necessary to draw on the color of the soldered wires in the photos above, since I tore the I2C bus through the connector that can be seen in this photo under the processor board, it is more convenient to disassemble
In general, it looks like this
Without connector

With connector

I repeat, everything works as stated by the author, including the latest revision, where the EQ button is activated
PS: The photo was made by Nikon specially so that you could see more closely who the internet will be long to open

Post has been editedlieutenant - 11.10.15, 19:41

[7floor]

Lieutenant @ 10.10.2015, 14:49

when the tire rang, my 23 leg of the WM8731 codec corresponded to 25 leg of BD3702FV and 24 leg of WM8731 26 leg of BD3702FV, respectively. And really now everything is connected and works with overlap, can be seen on this photo

But what is this? The joke is that the original picture with the scheme, which I took as the basis (authorship2x4ever) just contained exactly such a connection. Then, when communicating in PM (I forgot already with whom) it turned out that the legs were mixed up. I re-read the datasheets, found that it really is in BD37 * 25-SCL, 26-SDA, in WM8731 24-SCLK, 23-SDIN and, therefore, properly connect 25-24 and 26-23. Made corrections to the scheme.
And then you write that it works the opposite for you from the corrected one.
Just some kind of tin, I will go to call back in fact! :)

Yes, for those who may be afraid of such problems - tangled wires do not burn anything, just does not work.

[Sdes]

Lieutenant @ 10.10.2015, 14:49

I repeat, everything works as stated by the author.

Well, the most important thing? Is there any difference in sounding?

[lieutenant]

SDes,
Ohhh, this is not to describe here, I now unscrew as I want, this is the best I've tried

[7floor]

SDes @ 10.10.2015, 15:13

Just some kind of tin, I will go to call back in fact!

I rang the bell. I have everything on the diagram, i.e. BD 25 - WM 24 and BD 26 - WM 23
lieutenantcheck yourself again, maybe you got your legs mixed up twice (i.e., you got them mixed up once, and then you crossed them and eventually worked).
Although I have BD37534FV, and you have BD3702FV, but according to the datasheets they all have the same legs.

[lieutenant]

7floor,Everything is normal, working moments, everything will settle down, the main result is superior to expectations

[lieutenant]

7floor,
Checked 24 foot WM goes to R71, 23 to R70

[7floor]

Lieutenant @ 10.10.2015, 16:48

Checked 24 foot WM goes to R71, 23 to R70

This does not tell me anything, as I can see in the pictures, the elements are not marked at all :)
Well, if you call further, to the resistors BD37 *, and then to his feet?

[sergey0707]

SuperKungFu @ 10/05/2015, 14:33

judging by thisvideointerference in the fm range is generated by this element

Question, was it a specific instance problem or a common problem?
What was the solution and did the reception improve?

[mazepa2000]

sergey0707,

Sergey0707 @ 10.10.2015, 17:16

Question, was it a specific instance problem or a common problem?

Rather, a particular car.

[lieutenant]

7floor @ 10/11/2015, 16:59

Well, if you call further, to the resistors BD37 *, and then to his feet?

Some devilry, I collected it according to the scheme from the instruction, carried it to the car, I don’t have control of the bus, came to call, I see it wrong, turned it in the connector and carried it to try the disassembled, it all worked.
Then I took it apart and checked it again, sort of like on a datasheet, only the resistance near the MCU is not as in the instructions (on the contrary), apparently this confused me.
Post description edited

Post has been editedlieutenant - 11.10.15, 19:06