Assistant
REPLY |
MiWiFi mini | Xiaomi Mi-router mini - Firmware | [firmware] |
Message#1 25.08.15, 21:07 | |
Mushrooms run out, letters almost [offline] Topics Curator Group: Curators Messages 4435 Check in: 19.06.11 Xiaomi Mi 5S 4/128 Reputation: 1297 | MiWiFi mini | Xiaomi Mi-router mini- Firmware Discussion � | Firmware � Official page | MiWiFi | Xiaomi Mi-router � | Xiaomi MiWiFi nano � | Xiaomi MiWiFi 3 � | Xiaomi MiWiFi (client for Android)� | Xiaomi club � | PROMETHEUS scripting system � FAQ Firmware comparison Currently there is3 workersfirmware for our little animal with you: 1. Stock firmware: Pros: • Pre-installed and working; • Has the ability to control through the app on a smartphone. Minuses: • Chinese and • No support for USB modems; • There is no normal L2TP support from Beeline (thank God, the Beeline changed its mind and in some regions allowed to connect without a tunnel); • No IGMP support (IPTV); • Strongly loads the processor. 2. OpenWRT (PandoraBox) Pros: • Flexible and with patience it can be completed by installing additional packages. Minuses: • Requires SSH access, and some configuration. 3. XRMWRT (Padavan) Pros: • Works great and is easily customizable; • Excellent speed and stability; • Everything comes immediately in the kit; • The presence of skins; • The standard firmware package includes a lot of programs; • High security; • Initially in Russian. Minuses: • Does not extend in open access, demands independent assembly; • Requires access to SSH; • The system section is read only. How to get access via SSH and flash the router How to bind a router to an account with access via L2TP If your provider provides the Internet through an L2TP connection, you will have to connect a router through the old one, for this, connect them to the LAN-LAN. The router will be available as an access point, you will only need to find its IP address, for this scan the network with an old router or via a PC. How to upload any file to the device "Plan A" From any network share, download with the console command: wget (full link to firmware) -P / tmp "Plan b" Can use WinSCP (in SCP mode) in order to push the required file into the tmp folder: protocol - SCP, host - 192.168.31.1, port - 22, name - root, password - your password you received along with the SSH file. How to flash any firmware 1. Determine where to write the firmware with the command: cat / proc / mtd 2. Remember what the console gives you: it can be "firmware", "OS1" or "Firmware_Stub"; 3. Flash the firmware lying along the path /tmp/your_proshivka.bin with the command: mtd -r write / tmp / (your_program) (section_name) Where(section_name) - section ("firmware", "OS1" or "FirmwareStub" depending on your device); (your_proshivka) - the name of the firmware file. Please note that on the XRMWRT firmware, the command and section will be different: mtd_write -r write / tmp / (your firmware) Firmware_Stub Back up partitions To display sections we write: cat / proc / mtd Kernel + RootFS backup is not needed. Firmware_Stub is the sum of the Kernel + RootFS partitions. Ie the firmware image is entirely there, the entry point to RootFS is calculated automatically from the offset in the header image. If the backup folder was created on the HDD, the approximate path to save will be / media / AiDisk_a1 / backup Note, the path depends on the firmware. In turn, save: cp / dev / mtd0 / media / AiDisk_a1 / backup cp / dev / mtd1 / media / AiDisk_a1 / backup cp / dev / mtd2 / media / AiDisk_a1 / backup cp / dev / mtd5 / media / AiDisk_a1 / backup cp / dev / mtd6 / media / AiDisk_a1 / backup (alternative way to drain) After the procedure, it is desirable to transfer everything to the computer, and restore it if necessary (note that the openwrt command will notmtd_write , but mtd ): mtd_write write /media/AiDisk_a1/backup/mtd0.bin Bootloader mtd_write write /media/AiDisk_a1/backup/mtd1.bin Config mtd_write write /media/AiDisk_a1/backup/mtd2.bin Factory mtd_write write /media/AiDisk_a1/backup/mtd5.bin Storage mtd_write write /media/AiDisk_a1/backup/mtd6.bin Firmware_Stub Problem with logging in live Kaspersky Try changing the subnet from 192.168.31.1 to 192.168.1.1. No part of settings Try to connect via SHTTP or not via Wi-Fi and LAN. The web interface of the stock firmware does not open One of the domestic antiviruses was noticed on blocking it, well, correctly, I would block Chinese garbage too, it can be treated by deleting it before flashing it.Read more ... Information unit in binary numbering system GOST 8.417-2002 GSI bit2(bit) - amount of information 1 (usually used to denote the connection speed and the amount of information transmitted); byte2,3 - amount of information 1 equal to8bit (usually used to denote the amount of data on the media). 1) The term “amount of information” is used in devices for digital processing and transmission of information, for example in digital computing (computers), to record the amount of storage devices, the amount of memory used by a computer program. 2) In accordance with the international standard IEC 60027-2, the “bit” and “byte” units are used with SI prefixes. 3) Historically, there is such a situation that the name “byte” is incorrect (instead of 1000 = 103accepted 1024 = 210) used (and use) SI prefixes: 1 Kbyte = 1024 bytes, 1 MB = 1024 Kbytes, 1 Gbytes = 1024 Mbytes, etc. At the same time, the designation Kbytes start with a capital letter unlike the lowercase letter “k” to designate a multiplier ten3. Stock firmware To switch to English, you need to change the region in the wifi settings and update the firmware. Or download English firmware Crack via browser plugin Where to get: The latest firmware and applications from the official site Developer Development Archive(in Chinese resource) Extreme firmware on 03/03/2018 Archive stock firmware for Xiaomi Mi-router mini (in json format) Setup: How to set up for the first timeinstruction frombrain_008 Fine tuningdata fromvamadir QOS setup SMB configuration Tuning the bridge through 5 GHz Getting ssh: Instructions for officially obtaining SSH Unofficial manual way to get ssh Please note that SSH is obtained not on the router, but on the firmware! If you need to activate and get a password on the SSH stock, then you simply allow it on the custom, and the login and password are usually the same as in the admin area. Any stock firmware version 2.x.x should come up, but not older than 2.9.x Checked versions for Xiaomi MiWiFi mini: v2.6.17,v2.1.6, v2.8.91 Modification: Transmission- download manager Recovery: Rollback to X-RM stock firmware Openwrt Origin Pandorabox Multi web Padavan Attention!When building, installing and configuring, consider the following: • The Chinese have messed up with gain Prometheus script and firmware distribution terms : � You can not distribute ready-made assembly devices for companies other than ASUS; • You can not use the script to build the firmware with proprietary modules; • It is strictly forbidden to distribute mods, patches and parts of the code that interfere with the above conditions. OfficialthemePROMETHEUS script and websitehttp://prometheus.freize.net All questions on the script and the compilation of the firmware is recommended to ask there. Videoinstructions for creating virtuals and compiling firmware Firmware helphere Instructions in pictures The first steps: New instruction, without unnecessary problems ( source code update log ) EEPROM Patch or Reference Replacement be sure to put (Yes, true. Yes, you also need it. Yes, you really need it on Padavan. Yes, and you need the latest version. If you install via Prometheus, you don’t need to install a second time.) If the stars are folded into a brick For a snack: Audio setup Instructions in Russian for setting the firmware Installing a network printer Transmission Setup Ad blocker Ad blocking filter Owncloud + nginx + php5-fpm + https cloud (updated 05/12/2016) WEB interface to Aria2 How to add support for scanners in the firmware how to add your playlist m3u Adding TOR support Bypassing Roskomnadzor locks using TOR Using OpenVPN to bypass locks How to configure cron (autostart) How to configure QoS Skins: All skins should be replaced at the compilation stage of the firmware, the Prometheus script supports all skins, the skin change is carried out through the admin panel of the router. Multiskin not tied to version Outdated varsii skins Light skin outdated Skin in gray tones outdated Skin in yellow tones outdated Skin in blue outdated Skin in dark blue outdated Other: How to turn a WAN into a LAN Remote control multifunction device Video build and firmware Boot sectors Attention!Do not know what it is? Do not touch! Advantages of custom loaders, it is an opportunity to restore the custom firmware immediately, unlike the stock one, which can only be restored to the virgin state. Please note that if you suddenly make a mistake in something when flashing the boot sector, you will get a brick to support the table leg, by the way is very convenient. U-Boot from xrmwrt (does not work with drain) U-Boot from the Chinese (heaped up and Chinese) U-Boot from Pandora Box (Chinese) U-boot stock Stitching Before flashing, be sure to check md5, in case of a broken file, get a brick. How to load uboot into the router read in the FAQ section. After downloading, check the checksum: md5sum /tmp/uboot.bin Be sure to verify the amount issued! If xrmwrt: mtd_write write /tmp/uboot.bin Bootloader If openwrt: mtd write /tmp/uboot.bin Bootloader Reboot the router: reboot On the drain, the bootloader is closed for writing. Instructions
Post has been editedferhad.necef - 10.01.19, 07:34 Reason for editing: lock bypass on routers with Padavan firmware and Keenetic OS |
Message#2 10.09.14, 22:43 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 300 Check in: 22.11.09 ZTE Nubia Z5S mini Reputation: 36 | Configure the router. 1. At the start you will see such a screen. Press the blue button 2. On the next screen will be asked to come up with a password that will stand on wi-fi and be required to access the web muzzle. (I forgot to make a screenshot, but everything is clear) 3. Next we will be offered to download the mobile application. Seconds after 10 qr code will disappear. 4. We get to the main settings screen. 5. Click the "Settings" button in the upper left corner. We get to the status page of the router. Here you can see the current version of the software, update it, reset the settings of the router. 6. The first tab on the left is the WI-FI settings. It's all elementary. 6.1 At the very bottom, you can choose the power of the wi-fi transmitter. 7. The next tab is the most interesting: Internet settings. Click the edit button. 8. Now it all depends on your provider. 8.1 If you have auto IP assignment, then choose DHCP. 8.2 If PPPoE, then: 8.3 If you have specific Internet settings, then: 8.4 If you need to set a specific MAC address, then switch the switch so that it becomes blue and drive in which one you need. 9. At the very bottom of the same page, you can configure the router operating mode: marshutizer or repeater. In the opened menu there will be 2 pictures, you will not be mistaken. 10. Access settings, black / white lists. 11. LAN settings. If you need to add something else, write. In some screens, a double hat, a glitch of a Windows print screen, there is no time to edit. If some moments from those not translated by me are incomprehensible, throw screenshots, we will understand together. Screenshot of the active window in Windows alt + prtscr. The remaining settings did not translate, because if you configure the Internet, you can translate everything through chrome. Post has been editedbrain_008 - 11.09.14, 11:09 |
Message#3 13.11.14, 00:09 | |
Veteran [offline] Group: Curators Messages 1839 Check in: 22.01.10 Xiaomi Mi 8 Lite 4/64 Reputation: 699 | Full, high-quality and firmware-independent translation of all Xiaomi Mi-router mini settings. At the moment, almost 100% of the interface has been translated. At times, there may be some inaccuracies and shortcomings, of which I ask to inform me in QMS Pros: 0. The presence of the Russian language 1. Stability. The firmware code does not change 2. Independence from the firmware version. 3. Cross-platform. Suitable for any OS and almost any browser. 4. Ability to self-update. With hands, brains and some rules Minuses: 0. The presence of the script 1. The need to install an additional browser plugin 2. Additional load on the system. The larger the script, the more it triggers the loading of the browser. Install script 1. Install the Userscripts program, such as: For maxthon: Violentmonkey For firefox: Greasemonkey, Scriptish For Chrome, Chromium: Tampermonkey For Opera 15: Tampermonkey, Violentmonkey For Opera 12: already built into the software 2. Go throughreferenceand install the script. Link for automatic installation:tyk. 3. Go to the site settings router (http://192.168.31.1/orhttp://miwifi.com) Please note that the script does not work immediately, but after about 1 sec. after loading the page / frame) Post has been editedSilenttwilight - 15.11.14, 19:03 Reason for editing: New complete version of the translation + design -------------------- Ericsson R520M - Mitsubishi Trium - T-Mobile SDA black - Eten G500 - Glofiish X500 - Glofiish X600 - HP rw6815 WM6.1 - MIO Mitac A502 - HTC HD mini - HTC Sensation - Lenovo P780 - Xiaomi Mi2s - Xiaomi Redmi 2 - Xiaomi Redmi 4x - Xiaomi Mi8 Lite Details about translations in Profile |
Message#4 25.12.14, 17:01 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2385 Check in: 08.08.12 Xiaomi Mi 2S Reputation: 441 | General post on Xiaomi Router Mini (X-RM): Instructions for officially obtaining SSH on Xiaomi Router Mini Installation instructions for the Pandora Box firmware [r583-20140827] Russification and installation of additional packages Rollback to stock firmware Post has been editedlightvik - 29.12.14, 18:44 -------------------- |
Message#5 25.12.14, 17:59 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2385 Check in: 08.08.12 Xiaomi Mi 2S Reputation: 441 | Instructions for officially obtaining SSH on Xiaomi Router Mini: We do everything on our ownfear and risk! Internet is required on the router to link it to the xiaomi account! 1) You need to download the development (developed) firmware version for Xiaomi Router Mini (hereinafter referred to as X-RM). You can get it at -http://www1.miwifi.com/miwifi_download.html 2) You need to flash the dev version of the firmware via the web-interface of the router, for this: Go to the address 192.168.31.1 (if we did not change the subnet / ip of the router in the settings, then the address would be such), press the firmware selection button, point it to the .bin file we downloaded in the first paragraph and press the button. After that, the router will start updating the firmware - it lasts 1-2 minutes, as soon as it ends - you need to go to the web-interface of the router and perform the initial setup. 3) Now we need to bind the Xiaomi account to X-RM, if it is not there, it can be registered athttps://account.xiaomi.com/(there is a button to switch to English at the bottom of the page, or use Google translate), if you register by mail - don’t choose mail.ru and other Russian mail services - a confirmation letter can go 24-72 hours or not come at all, use Gmail! We also need to install the application on a PC or phone, and from this device you need to bind the router to your Xiaomi account, I think the easiest way to do this is using the android client on the phone / tablet. 4) After you bind the router to your account, you need to go tohttps://d.miwifi.com/rom/ssh, on this page you need to log in to xiaomi account, and after you will see something like this page Near the desired router (you can link several to one account - as can be seen in the screenshot), press the button, and confirm the selection with the right button. The correct result will be the downloaded file miwifi_ssh.bin 5) you need to find a USB-Flash drive, preferably not a very large volume (1-16GB) - formatted in fat32, it is desirable that it is empty, copy miwifi_ssh.bin to it, then you can proceed to unlock SSH, for this: Disconnect from the router power cable. USB-Flash disk inserted into the USB connector of the router. We press the reset button on the router with a thin sharp object (a toothpick for example). Connect the power cable. as soon as the router quickly blinks orange LED - release the reset button. USB-Flash disk can be removed after the router is completely turned off. As soon as the router boots up - you can try to connect via SSH to your router. Username root, Password - on pagehttps://d.miwifi.com/rom/sshnext to root, the connection port is 22 (standard). The router has SSH available only via LAN. To connect to it via WAN, you need to change the configs / etc / config / dropbear and / etc / config / firewall If SSH is missing, then you have made a mistake somewhere, most likely either the router is not bound, or after the 're-binding' you need to download a new .bin file. After you connect via SSH - I recommend changing the user's password using the command: passwd After entering it, you will need to enter a new password and confirm it. Post has been editedlightvik - 19.01.18, 12:04 -------------------- |
Message#6 25.12.14, 18:46 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2385 Check in: 08.08.12 Xiaomi Mi 2S Reputation: 441 | Instructions for installing the firmware Pandora Box [r583-20140827] in the Xiaomi Router Mini [X-RM] Ssh access required WAN access required[The Internet] We do everything on our ownfear and risk 1) Connect to our router via SSH |according to the standard, its address is 192.168.31.1, port 22 2) Download the file with the firmware in the / tmp router command wget http://downloads.openwrt.org.cn/PandoraBox/Xiaomi-Mini-R1CM/stable/PandoraBox-ralink-mt7620-xiaomi-mini-squashfs-sysupgrade-r1024-20150608.bin -P / tmp 3) Determine where to write the firmware, with the command cat / proc / mtd 4) Flash the firmware lying along the path /tmp/pandora.bin with the command: mtd -r write /tmp/PandoraBox-ralink-mt7620-xiaomi-mini-squashfs-sysupgrade-r1024-20150608.bin XYZ The login username is root, the password is admin As a result, we get a full-fledged stable openwrt 12.09.1 Attitude Adjustment with an attached working package repository for X-RM, which also includes kernel modules (allow connecting 4G modems, and other peripherals, add support for other file systems, etc ...) If the Pandora Box is stitched in your router and you want to return the stock firmware, this instruction will help you ->Link Post has been editedFreize - 13.07.15, 19:51 Reason for editing: Fixed broken links -------------------- |
Message#7 25.12.14, 19:04 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2385 Check in: 08.08.12 Xiaomi Mi 2S Reputation: 441 | Installing packages in the Pandora Box firmware [r583-20140827] [Important!] Before installing the packages, we need to run the package update command every time: opkg update Installing a native openwrt theme opkg install luci-theme-openwrt Russification of the Luci web interface in Pandora Box wget ftp: //[email protected]: [email protected]/russian.tar.gz -P / tmp tar -zxvf /tmp/russian.tar.gz -C / reboot After the reboot, the Russian language item will appear in the settings. Post has been editedlightvik - 08.01.15, 20:25 -------------------- |
Message#8 26.12.14, 06:57 | |
Guru [offline] Group: Friendssavagemessiahzine.com Messages 2385 Check in: 08.08.12 Xiaomi Mi 2S Reputation: 441 | Rollback to X-RM stock firmware: 1) Download the stock firmware for X-RM (stable or developer of your choice) - you can download it herehttp://www1.miwifi.com/miwifi_download.html 2) Rename the downloaded * .bin file with the firmware to a file called miwifi.bin 3) We need a 1-16GB USB flash drive formatted in FAT32, with no files inside (empty) 4) Put the file miwifi.bin in the root of the USB flash drive 5) Disconnect the power cable from the X-RM, insert the USB Flash drive into the usb input of the router, hold down the RESET button with a thin sharp object (such as a toothpick), connect the power cord to the router - without pressing the reset button when the router blinks with an orange LED - the RESET button can be let go. 6) After some time, the router will be available at 192.168.31.1 - you can perform the initial setup Post has been editedlightvik - 15.10.16, 06:33 -------------------- |
Message#9 10.01.15, 16:04 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | And so, I bought myself this device on NG. Impressions are more good than bad. Well, polazil in the guts. Can someone come in handy Official Chinese firmware 0.7.31 XiaoMi Router Mini Specs CPU MT7620A rev.0206 aka MT7620N (H) ver: 2 eco: 6 system type: Ralink SoC processor: 0 cpu model: MIPS 24Kc V5.0 BogoMIPS: 385.84 wait instruction: yes microsecond timers: yes tlb_entries: 32 extra interrupt vector: yes hardware watchpoint: yes, count: 4, address / irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] ASEs implemented: mips16 dsp shadow register sets: 1 core: 0 VCED exceptions: not available VCEI exceptions: not available Equipment 3: 1852 Ralink eth0 4: 23378 Ralink wl1 5: 57653 Ralink timer 6: 0 Ralink ralink_gpio 12: 6982 Ralink serial 13: 12243 Ralink wl0 17: 3 Ralink Ralink_ESW 18: 5623 Ralink ehci_hcd: usb1, ohci_hcd: usb2 WiFi settings / etc / config / wireless config wifi-device 'mt7612' option type 'mt7612' option vendor 'ralink' option channel '0' option bw '0' option autoch '2' option radio '1' option txpwr 'mid' option hwband '5G' option hwmode '11ac' option disabled '0' option country 'CN' option region '1' option aregion '0' config wifi-iface option device 'mt7612' option ifname 'wl0' option network 'lan' option mode 'ap' option ssid 'Xiaomi_5G' option encryption 'mixed-psk' option key 'password' config wifi-device 'mt7620' option type 'mt7620' option vendor 'ralink' option channel '0' option bw '0' option autoch '2' option radio '1' option txpwr 'mid' option hwband '2_4G' option hwmode '11ng' option disabled '0' option country 'CN' option region '1' option aregion '0' config wifi-iface option device 'mt7620' option ifname 'wl1' option network 'lan' option mode 'ap' option ssid 'Xiaomi' option encryption 'mixed-psk' option key 'password' Network and Internet settings / etc / config / network config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option ifname 'eth0.1' option type 'bridge' option proto 'static' option ipaddr '192.168.31.1' option netmask '255.255.255.0' config interface 'diagnose' option ifname 'eth0.1' option proto 'static' option ipaddr '192.168.88.8' option netmask '255.255.255.0' config interface 'ifb' option ifname 'ifb0' config interface 'wan' option proto 'pppoe' option mtu '1480' option special '0' option username 'login adsl' option password 'password ads' option ifname 'eth0.2' Firewall firewall / etc / config / firewall config defaults option syn_flood '0' option input 'ACCEPT' option output 'ACCEPT' option forward 'REJECT' config zone option name 'lan' option network 'lan' option input 'ACCEPT' option output 'ACCEPT' option forward 'REJECT' config zone option name 'wan' option network 'wan' option input 'REJECT' option output 'ACCEPT' option forward 'REJECT' option masq '1' option mtu_fix '1' config forwarding option src 'lan' option dest 'wan' config rule option name 'Allow-DHCP-Renew' option src 'wan' option proto 'udp' option dest_port '68' option target 'ACCEPT' option family 'ipv4' config rule option name 'Allow-Ping' option src 'wan' option proto 'icmp' option icmp_type 'echo-request' option family 'ipv4' option target 'ACCEPT' config rule option name 'Allow-DHCPv6' option src 'wan' option proto 'udp' option src_ip 'fe80 :: / 10' option src_port '547' option dest_ip 'fe80 :: / 10' option dest_port '546' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Input' option src 'wan' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' list icmp_type 'router-solicitation' list icmp_type 'neighbor-solicitation' list icmp_type 'router-advertisement' list icmp_type 'neighbors-advertisement' option limit '1000 / sec' option family 'ipv6' option target 'ACCEPT' config rule option name 'Allow-ICMPv6-Forward' option src 'wan' option dest '*' option proto 'icmp' list icmp_type 'echo-request' list icmp_type 'echo-reply' list icmp_type 'destination-unreachable' list icmp_type 'packet-too-big' list icmp_type 'time-exceeded' list icmp_type 'bad-header' list icmp_type 'unknown-header-type' option limit '1000 / sec' option family 'ipv6' option target 'ACCEPT' config include 'wanmonitor' option path '/usr/sbin/wan.monitor start' option reload '1' option enabled '1' config include 'webinitrdr' option path '/lib/firewall.sysapi.loader webinitrdr' option reload '1' option enabled '1' config include 'dnsmiwifi' option path '/lib/firewall.sysapi.loader dnsmiwifi' option reload '1' option enabled '1' config include 'portalfilter' option path '/lib/firewall.sysapi.loader portalfilter' option reload '1' option enabled '1' config include 'macfilter' option path '/lib/firewall.sysapi.loader macfilter' option reload '1' option enabled '1' config include 'miqos' option path '/lib/firewall.sysapi.loader miqos' option reload '1' config include 'firewalluser' option path '/etc/firewall.user' option reload '1' config include 'dmz_bypass_ctf' option path '/lib/firewall.sysapi.loader dmz_bypass_ctf' option reload '1' config rule 'xunleiwantcpports' option name 'xunlei wan accept tcp port 1080 4662 2080 2062' option src 'wan' option dest_port '1080 4662 2080 2062' option proto 'tcp' option target 'ACCEPT' config rule 'xunleiwanudpports' option name 'xunlei wan accept udp port 4661 3027 888 666 2037 2061 2048 2066' option src 'wan' option dest_port '4661 3027 888 666 2037 2061 2048 2066' option proto 'udp' option target 'ACCEPT' config rule 'shuijingwantcpports' option name 'shuijing wan accept accept tcp port 4593' option src 'wan' option dest_port '4593' option proto 'tcp' option target 'ACCEPT' config rule 'shuijingwanudpports' option name 'shuijing wan accept udp port 4693' option src 'wan' option dest_port '4693' option proto 'udp' option target 'ACCEPT' config rule 'guest_8999' option name 'Hello wifi 8999' option src 'guest' option proto 'tcp' option dest_port '8999' option target 'ACCEPT' config rule 'guest_8300' option name 'Hello wifi 8300' option src 'guest' option proto 'tcp' option dest_port '8300' option target 'ACCEPT' config rule 'guest_7080' option name 'Hello wifi 7080' option src 'guest' option proto 'tcp' option dest_port '7080' option target 'ACCEPT' config include 'miniupnpd' option type 'script' option path '/usr/share/miniupnpd/firewall.include' option family 'IPv4' option reload '1' XiaoMi QoS Shaper Traffic / etc / config / miqos config miqos 'settings' config miqos 'settings' option name 'settings' option qos_ack '0' option qos_syn '1' option qos_fin '1' option qos_rst '1' option qos_icmp '1' option qos_small '1' option upload '2330' option download '19190' option enabled '1' option qos_auto '0' config limit 'guest' option name 'guest' config group '00' option name '00' option max_grp_uplink '0' option max_grp_downlink '0' option min_grp_uplink '0' option min_grp_downlink '0' option mode 'general' list mac '00' config mode 'general' option name 'general' list subclass 'p1' list subclass 'p2' list subclass 'p3' list subclass 'p4' list subclass 'p5' config system 'param' option name 'param' option burst '10k' option interval '10' option default_mode 'general' option default_group '00' config class 'p1' option ceil '1.0' option burst '10k' option tos 'Minimize-Delay' option rate '0.1' option name 'p1' option udp_ports '37, 53,123,3455,27000:27015' option tcp_ports '37, 53,123,3455 ' config class 'p2' option ceil '0.98' option burst '10k' option tos 'Minimize-Cost' option rate '0.2' option name 'p2' option udp_ports '22, 2222,3389,3478,3479,5060: 5063,3478:4380' option tcp_ports '22, 2222,3389,3478,3479,5060: 5063 ' config class 'p3' option ceil '0.99' option burst '6k' option tos 'Maximize-Reliability' option rate '0.5' option name 'p3' option tcp_ports '80, 443,8080 ' config class 'p4' option name 'p4' option burst '6k' option ceil '0.98' option rate '0.1' option tcp_ports '110,143,220,585,993,995' config class 'p5' option name 'p5' option burst '6k' option ceil '0.99' option rate '0.1' config group 'AA: AA: AA: AA: AA: AA' option name 'AA: AA: AA: AA: AA: AA' option mode 'general' list mac 'AA: AA: AA: AA: AA: AA' option min_grp_uplink '0.25' option min_grp_downlink '0.25' option max_grp_uplink '0.75' option max_grp_downlink '0.75' config group 'AV: AV: AV: AV: AV: AV' option name 'AV: AV: AV: AV: AV: AV' option mode 'general' list mac 'AV: AV: AV: AV: AV: AV' option min_grp_uplink '0.25' option min_grp_downlink '0.25' option max_grp_uplink '0.75' option max_grp_downlink '0.75' config group 'BB: BB: BB: BB: BB: BB' option name 'BB: BB: BB: BB: BB: BB' option mode 'general' list mac 'BB: BB: BB: BB: BB: BB' option min_grp_uplink '0.25' option min_grp_downlink '0.25' option max_grp_uplink '0.25' option max_grp_downlink '0.25' # These are the settings for my 2 PCs. There is a percentage of cutting traffic, at least 25% and 75% of the maximum from the Internet channel. # This is the setting for my phone. There is a percentage of cutting traffic, at least 25% and 25% of the maximum from the Internet channel. # My changes via ssh for steam. Ports for games and voice chat. AND MY Speed, which is determined by the router # Settings can be created as follows, go to the Web interface>qos>manual settings>determine the maximum and minimum speed of devices>waiting for conservation. Connect via ssh and edit / etc / config / miqos more individually. # Q If QOS is configured via the Interface, then the minimum is setting 优先 级 which is of 3 types (低 - 25%, 中 - 50%, 高 - 75%) # !!!!! If the QOS is changed via the PC web interface or the TELEPHONE interface !!!! THEN IT WILL LOSS THE SETTINGS you did through ssh Post has been editedvamadir - 10.01.15, 16:51 Reason for editing: added qos settings -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 downloadXiaoMi MiBand 2 |
Message#10 18.01.15, 09:01 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | QOS setup [email protected], 06:58 Similarly, I did not guess to look. Customized, thanks! For each connected device. And, sort of like, even priorities are set. Delivered 25/90%. The default was 100/100%. As far as I understand, there are no restriction settings for outgoing traffic? a little wrong. in QOS 3 settings Setting 优先 级 which is of 3 types (低 - 25%, 中 - 50%, 高 - 75%) - these are the minimum outgoing / incoming traffic that the device can use. then the maximum outgoing / incoming. here you yourself put a percentage of the channel. Example. I have a 25% minimum and 75% maximum for all PCs. those.低 / 75/75. for phones I have 低 / 25/25. those. my phones have 25 minimum outgoing / incoming and maximum outgoing 25 incoming 25. P.S. 下 - incoming 上 - outgoing In order for the speed to be cut normally, it is better to use the speed check of the router itself. And not what the provider said. My provider promised 20M for a jump and 4 for a return. In real life, 18M for a jump and 1.8M for a return. Accordingly, if you do not have a real speed, then there is simply nowhere physically anywhere to take speed. Post has been edited-SunLion- - 19.01.15, 00:11 Reason for editing: In the header -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#11 18.01.15, 09:26 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | SMB configuration Something about SharyWhen you connect a hard disk (flash drive). The SMB settings and folders for the router are created on the USB device (it is not recommended to delete, it may not earn SMB). P.S You can edit the file on USB xiaomi_extSharePath.cfg in him SN-11111111111111 = ["/ 共享", "/ 下载"]; You can add or delete these folders for sharing on the network. Example. Insert the hard drive, wait for 4 minutes, no less. We look that on a network folders "共享", "下载" are visible. Then we disconnect the device from the USB router to the PC and edit xiaomi_extSharePath.cfg. For example, so SN-11111111111111 = ["/ Video", "/ Music", "/ Anime", "/ Picture"]; . Accordingly, these folders must be created on USB. Disable USB and connect to the router. And we see in 4 minutes approximately our folders in the network Post has been edited-SunLion- - 19.01.15, 00:19 Reason for editing: In the header -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#12 25.01.15, 20:43 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | Transmission XIAOMI Mini FAQ on transmission Connecting and checking HDD, here the last line shows that everything was mounted root @ XiaoQiang: ~ # df -h Filesystem Size Used Available Use% Mounted on rootfs 10.5M 10.5M 0 100% / / dev / root 10.5M 10.5M 0 100% / tmpfs 61.4M 2.4M 59.0M 4% / tmp tmpfs 512.0K 0 512.0K 0% / dev / dev / mtdblock7 1.0M 752.0K 272.0K 73% / data / dev / mtdblock7 1.0M 752.0K 272.0K 73% / etc tmpfs 61.4M 2.4M 59.0M 4% / userdisk / sysapiht tpd / dev / root 1.0M 752.0K 272.0K 73% / mnt / dev / mtdblock7 1.0M 752.0K 272.0K 73% / mnt / dev / sda1 931.5G 614.8G 316.7G 66% / extdisks / sda1 Editing repositories to install dependencies. Also added a link to an external hard drive. root @ XiaoQiang: ~ # vi /etc/opkg.conf src / gz attitude_adjustment http://downloads.openwrt.org/barrier_breaker/14.07/ramips/mt7620a/packages/base dest root / data dest ram / tmp lists_dir ext / data / var / opkg-lists option overlay_root / data dest usb / extdisks / sda1 / opkg We update dependences for a rocking chair root @ XiaoQiang: ~ # opkg update Create a directory on an external disk root @ XiaoQiang: ~ # mkdir / extdisks / sda1 / opkg go to the directory root @ XiaoQiang: ~ # cd / extdisks / sda1 / opkg Download the libc library and install it (because of a bug, opkg cannot install it by itself) root @ XiaoQiang: / extdisks / sda1 / opkg # wget http://downloads.openwrt.org/barrier_breaker/14.07/ramips/mt7620n/packages/base/libc_0.9.33.2-1_ramips_24kec.ipk root @ XiaoQiang: / extdisks / sda1 / opkg # opkg -d usb install libc_0.9.33.2-1_ramips_24kec.ipk Install other dependencies root @ XiaoQiang: ~ # opkg -d usb install libcurl libevent2 libopenssl libpthread librt Check whether everything is established root @ XiaoQiang: / extdisks / sda1 / opkg # opkg list-installed libc - 0.9.33.2-1 libcurl - 7.38.0-1 libevent2 - 2.0.21-1 libgcc - 4.8-linaro-1 libopenssl - 1.0.1j-1 libpolarssl - 1.3.8-2 libpthread - 0.9.33.2-1 librt - 0.9.33.2-1 zlib - 1.2.8-1 If everything is fine, then install the torrent itself rocking. Again we edit repositories root @ XiaoQiang: / extdisks / sda1 / opkg # vi /etc/opkg.conf src / gz attitude_adjustment http://downloads.openwrt.org/barrier_breaker/14.07/ramips/mt7620a/packages/packages dest root / data dest ram / tmp lists_dir ext / data / var / opkg-lists option overlay_root / data dest usb / extdisks / sda1 / opkg Update and install root @ XiaoQiang: / extdisks / sda1 / opkg # opkg update root @ XiaoQiang: / extdisks / sda1 / opkg # opkg -d usb install transmission-daemon transmission-web Run the transmission-daemon to create a folder with settings root @ XiaoQiang: / extdisks / sda1 / opkg # export TRANSMISSION_WEB_HOME = / extdisks / sda1 / opkg / usr / share / transmission / web root @ XiaoQiang: / extdisks / sda1 / opkg # / extdisks / sda1 / opkg / usr / bin / transmission-daemon -g / extdisks / sda1 / opkg / transmission-daemon stop transmission root @ XiaoQiang: / extdisks / sda1 / opkg # killall -HUP transmission-daemon We configure the transmission, here you just need to change a few lines root @ XiaoQiang: / extdisks / sda1 / opkg # vi /extdisks/sda1/opkg/transmission-daemon/settings.json "download-dir": "/ extdisks / sda1 / downloads", "rpc-port": 9876, "rpc-whitelist-enabled": false, Insist firewall, but these lines needadd to the end of the file root @ XiaoQiang: / extdisks / sda1 / opkg # vi / etc / config / firewall config rule 'transmission_web' option src 'wan' option dest_port '9876' option proto 'tcp' option target 'ACCEPT' option name 'transmission mgmt from wan' config rule 'transmission_peer_tcp' option src 'wan' option dest_port '51413' option proto 'tcp' option target 'ACCEPT' option name 'transmission incoming tcp' config rule 'transmission_peer_udp' option src 'wan' option dest_port '51413' option proto 'udp' option target 'ACCEPT' option name 'transmission incoming udp' Restart firewall root @ XiaoQiang: / extdisks / sda1 / opkg # /etc/init.d/firewall restart create a link and start the rocking chair (you need to enter every time after the reboot) root @ XiaoQiang: / extdisks / sda1 / opkg # export TRANSMISSION_WEB_HOME = / extdisks / sda1 / opkg / usr / share / transmission / web / root @ XiaoQiang: / extdisks / sda1 / opkg # / extdisks / sda1 / opkg / usr / bin / transmission-daemon -g / extdisks / sda1 / opkg / transmission-daemon Well, go to the web-facehttp://192.168.31.1:9876 Mini Editor FAQ vi to edit clicki to save clickescthen:thenwq to cancelescthen : thenq! Edit / paste will be where the cursor is blinking The insert works normally only in the editing mode, i.e. after you clickedi The cursor moves by arrows. M Check outForum Rules! 5.3. Implicit or explicit extortion of raising a reputation is forbidden, for example: “I helped you, and you didn’t even say thanks!” Or “You could have raised your reputation!” If you deserve a raise of reputation, you will be raised without reminders. Post has been edited-SunLion- - 31.01.15, 15:21 Reason for editing: in the header -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#13 26.01.15, 12:36 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 821 Check in: 21.12.10 Xiaomi Redmi Note 4X Snapdragon 3/32 Reputation: 151 | [email protected], 20:43 Transmission XIAOMI Mini FAQ on transmission Is it for pandora or stock? Post has been editedemlonlife - 26.01.15, 17:03 |
Message#14 26.01.15, 13:02 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | [email protected], 17:36 Is it for pandora or stock? This is a stock, no problems with pandora. P.S. For pandora #vi /etc/opkg.conf arch all 1 arch noarch 1 arch ralink 10 arch ramips_24kec 20 dest root / dest ram / tmp lists_dir ext / var / opkg-lists option overlay_root / overlay src / gz pandorabox http://downloads.openwrt.org.cn/PandoraBox/ralink/mt7620/packages #opkg update #opkg install install transmission-daemon transmission-web luci-app-transmission Post has been editedvamadir - 26.01.15, 13:03 -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#15 26.01.15, 13:13 | |
Veteran [offline] Group: Friendssavagemessiahzine.com Messages 1316 Check in: 26.01.13 Xiaomi Redmi 6 Pro 3/32 Reputation: 45 | |
Message#16 26.01.15, 13:45 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | make plz instruction for those who did not work with linux. For example, I have no idea where to enter it all. Need to get ssh access as I understand it? Yes, you need ssh access. If you don't know, it's better not to touch anything, you can break everything. If you are not afraid then experiment at your own risk :) Post has been editedvamadir - 26.01.15, 19:37 Reason for editing: Removed unnecessary -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#17 26.01.15, 23:14 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 62 Check in: 02.08.13 Reputation: 6 | [email protected], 20:43 create a link and start the rocking chair (you need to enter every time after the reboot) root @ XiaoQiang: / extdisks / sda1 / opkg # export TRANSMISSION_WEB_HOME = / extdisks / sda1 / opkg / usr / share / transmission / web / root @ XiaoQiang: / extdisks / sda1 / opkg # / extdisks / sda1 / opkg / usr / bin / transmission-daemon -g / extdisks / sda1 / opkg / transmission-daemon The question is not modest: why can't you add to rc.local? Post has been editedVbh99 - 26.01.15, 23:20 |
Message#18 26.01.15, 23:49 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | Added, but for some reason it does not run these lines rc.local. I also tried through the bash script, it also did not work. Apparently my hands are not from that place: ( -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
Message#19 27.01.15, 02:04 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 62 Check in: 02.08.13 Reputation: 6 | Added, but for some reason it does not run these lines rc.local. I also tried through the bash script, it also did not work. apparently my hands are not from that place Then you need to run with a timer. rc.local is executed when not everything is loaded yet. In this case, the router will hang after a reboot. This, though unnerving, but not critical. http: //www.cyberciti.b…-sleep-bash-scripting/ I think 2 seconds will be enough. This, of course, is a dirty hack and so it is impossible to do, but it will come down like that. On good, these lines probably need to be crammed with the init.d script for the transmission-daemon. :) By the way, you can not add a global variable every time. [email protected], 20:43 root @ XiaoQiang: / extdisks / sda1 / opkg # export TRANSMISSION_WEB_HOME = / extdisks / sda1 / opkg / usr / share / transmission / web / http: //www.cyberciti.b...va_home-path-variable/ Post has been editedVbh99 - 27.01.15, 02:16 |
Message#20 27.01.15, 08:44 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 749 Check in: 14.04.13 Reputation: 17 | [email protected], 04:39 Yes, you need ssh access. If you don't know, it's better not to touch anything, you can break everything. If you are not afraid then experiment at your own risk And for mere mortals, you can do the instructions so that the script can be run and everything is set up itself — the function is necessary, but I have no idea where and how to insert these codes. Ideally, of course, the firmware with a wired function, I think many were appreciative. |
Message#21 27.01.15, 10:46 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 90 Check in: 17.04.10 Asus Zenfone Max Pro (M2) ZB631KL Reputation: 22 | Thanks VBH99: thank_you: Thanks to you, I was able to autoload. vi / etc / profile Add to the end of the file sleep 10 export TRANSMISSION_WEB_HOME = / extdisks / sda1 / opkg / usr / share / transmission / web / / extdisks / sda1 / opkg / usr / bin / transmission-daemon -g / extdisks / sda1 / opkg / transmission-daemon Putting time less I do not advise Since it takes time to determine the hard disk. It is determined long enough. In general, after downloading, the torrent runs for about 2 minutes. What is not critical. -------------------- Dell Inspiron 3541 (UEFI) Windows 10 Asus ZenFone Pro M2 XiaoMi MiBand 2 |
mobile version | Now: 12.06.19, 18:06 |