Huawei E5186 - Discussion | [ltemodem] [mifi]



Rep: (1)
Huawei E5186 4G LTE CAT6 CPE Router

A photo:
Attached Image

Attached Image

Specifications:
Huawei E5186s-61a:
* LTE FDD 700/1800 / 2600MHz TDD 2300Mhz
* DC-PA + / HSPA + / UMTS 900 / 2100MHz
* GSM / GPRS / EDGE 850/900/1800 / 1900MHz
Attention: 61a aggregates only 2300 MHz (20 + 20).
Huawei E5186S-22a:
4G LTE FDD DD800 / 900/1800/2100 / 2600MHz, TDD 2600MHz
3G UMTS / WCDMA: 2100 / 900Mhz
2G GPRS / GSM / EDGE: 850/900/1800/1900 MHz
Aggregations supported by Huawei E5186s-22a
FDD CA:
- B3 + B7
- B3 + B20
- B7 + B20
- B3 intra-band contiguous
- B7 intra-band contiguous
TDD CA:
- B38 intra-band contiguous
Message в„–1345, author michael.lvf
Speed:
* LTE CAT6 Download speed up to 300mbps, download speed up to 50Mbps @ 20MHz + 20MHz BW
* LAN speed: 1000 Mbps. WAN speed: 1000 Mbps (Huawei E5186 - Discussion (Post limiter # 82938303)
Wi-Fi:
WiFi 802.11b / g / n / ac, 2.4GHz / 5GHz, simultaneous operation of up to 64 Wi-Fi devices
SIM card size: Micro SIM card
Connectors:
* 4 RJ45 (GE) interface + 2 RJ11 Interface + 1 USB host interface
Functions:
* Firewall, CS Voice, VoIP, VoLTE, TR069 Remote Management
* HTTP Online Upgrade, USB Share, UPnP
* IPV6, DLNA, Fax, Print
Dimensions: 194 x 177 x 64 mm, about 450g
Included:
1 * The device itself;
1 * Power Adapter;
1 * Ethernet cable;
2 * Antennas (not available in all operator versions)

Data transfer rates in various cellular networks:
4G / LTE FDD: Download: 300Mbit / s Recoil: 150Mbit / s
4G / TD-LTE: Download: 224Mbit / s Recoil: 20Mbit / s
3G DC-HSPA +: Download: 42Mbit / s Recoil: 5.76Mbit / s
3G HSPA +: Download: 21Mbit / s Recoil: 5.76Mbit / s
3G UMTS: Download: 384Kbit / s Recoil: 186Kbit / s

A source of information
FAQ
Q: How to unlock this device?
A: Find out the IMEI of your device (this information is on the label under the back cover). Calculate unlock codeaccording to algorithm 201 via this utility . Insert the SIM card of another operator (ie, not the one under which it is locked) into the device, then connect to the device via WiFi, or through the LAN port, go to the browser via the link http: //homerouter.cpe and in the window requesting the code, enter the code itself.
Q: How to use this router with unlimited tariffs Yota, MTS Unlimited, and so on?
A: First, you needchange IMEIand secondly installproshivka for "greedy" operators. After that, you can easily use the Internet at these rates.
Q: How does the E5186s-22a version differ from the E5186s-61a version?
A: Firstly, at E5186s-61a there is an aggregation of only frequencies of 2300 MHz (20 + 20). In the Russian Federation, with 2,300 federal operators do not work, sometimes (very rarely) regional ones work. With high probability, you will not be able to use the function of aggregation of channels on this router in Russia and in many European countries. Specify additionally, at what frequencies your operator operates.
E5186-22a works 100% in aggregation with any Russian and European operators.
Secondly, these models differ in frequencies. Version 61a - for Australia, Africa and some Asian countries, 22a - for Europe (including for Russia and other countries of the former USSR). This does not mean that the E5186s-61a will not work in Europe at all. All frequencies except the first (800 MHz at 22a and 700 MHz at 61a) are the same. This means that LTE will not work at 800 megahertz, the remaining frequencies (1800 MHz and 2600 MHz) coincide and will work without any problems. Since 800 MHz is a rather rare band (at least for Russia, and at least for now), this does not really matter. Accordingly, it is worth looking at the situation. If you don’t catch 800 MHz and you don’t need aggregation, or you don’t need it, you can save money and order the E5186s-61a version from aliexpress (or from somewhere else).
I repeat that 800 MHz, at least specifically in Russia, is not very widespread so far, so if you do not need aggregation, in most cases you can safely take the E5186s-61a. However, the 800 MHz range due to the relatively low frequency and, consequently, a larger coverage radius in the near future, is likely to be widely spread. If you live somewhere far from the tower and catches only 1800 MHz, then I recommend taking 22a, because it is possible that the 800 MHz range will soon open on your tower, which will help to increase the speed many times due to aggregation.
Q: Are the E5186s-22a and E5186s-61a firmware compatible?
Yes, the firmware is fully compatible. You can install either the E5186s-22a firmware on the E5186s-61a or vice versa.
Q: Where can I download the service firmware BV7R2C0update_21.282.99.80.00 - DOWNGRADE.gz.bin?
On MEGA(in the Original Huawei folder), there you can download this and others.
Instructions
Firmware

The curator of the topic is kolyanok. For filling caps, please contactin QMS

Post has been editedkolyanok - 05.03.19, 10:31
Reason for editing: LAN and WAN speed



Rep: (3)
* Aircraft fireman
thanks for the advice ;)

Post has been editedBB20 - 12.05.19, 19:02



Rep: (3)
BB20 @ 05/10/19, 18:52*
Greetings

I wanted to ask - on the new Windows 10 1809 E5186 Toolbox 0.9 does not open, so how can I overcome it? Compatibility did not help me ....



Understood - the problem was in Display --->Scale and layout
If custom scaling size is set, then the program does not open .... set Scale and Layout to 125% and the program opened.



Rep: (2)
Please tell me, maybe someone knows. By Ethernet, incoming traffic cuts at 100 megabits, no matter in which version the lace or wifi.

The speed cutoff started when I was sitting on the sim card. Now it is like a home AP access point.

Model: E5186s-22a
My number: Unknown
AO Version: CL1E5175HM
Software Version: 21.316.01.00.07
Web Interface Version: 16.100.02.00.03
MAC Address: B8: 08: D7: D4: FA: 2A
WAN IP Address: 192.168.8.254



Rep: (3)
* whot

A wire with 8 cores? Does 1 Gigabit show when connected to a router?



Rep: (643)
Vipost @ 05/12/19, 9:30 p.m.*
The instruction from the header for restoring ushatnykh routers (Power + WiFi is on) is not correct.
The problem is reproducible, and can be solved (relatively) easily,).


If it is incorrect, then write your ..



Rep: (2)
Yes, definitely gigabit. Now I noticed that on one port it downloads under 100 megabits, and through wifi speedtest 90 breaks. My channel is 300 megabits. Port division seems to work. It remains to find these settings through the API or the central config.

Post has been editedwhot - 13.05.19, 11:47



Rep: (83)
Airplane Fireman @ 05/12/19, 5:00 p.m.*
If you use the E5186 continuously for at least 5-6 hours, it overheats. A couple of times I had to wrap it with a flexible refrigeration generator - it got so hot. And this winter, the window is quite cool room. Of course - the connection at the same time jumped like a cow bitten by horseflies
Perhaps I haven’t tried anything sweeter than carrots: D But this box works for half a year in 24/7 mode. It does not overheat. Beeline feeds at least 5 devices without question. In B3 10 MHz speed: 30-40 in the afternoon, 50-70 at night. If you insert a Mega SIM card, then the speeds with CA 7_7 aggregation will be good for 100. I do not see the point of changing it.
5Hz Wi-Fi is rather weak. A repeater is connected to it.

Post has been editedmichael.lvf - 14.05.19, 16:24



Rep: (59)
* Demiurge67

You at least give links to the remaining devices)))

Posted on 05/14/2019, 22:51:

* Demiurge67

The megaphone's first model was the Huawei n5186 (R300-1). Now this is an archived version.

Now I tried other options that you indicated - did not find!)))).

Post has been edited1qqq - 14.05.19, 22:52



Rep: (23)
* Aircraft fireman
* kot1100,
Beeline, in principle, bottom speed, even with a "triplet."
In my opinion, there is no point in using this router with either tele2 or beeline.
There are two other normal operators.

Post has been editedpigovina - 15.05.19, 10:58



Rep: (39)
I got this device today. Of course, it was required to flash from greed - there was a native Megafon firmware.
The result of many hours of action is almost the sameresultcomrademichael.lvf :
1. I asked for BV7R2C0update_21.282.99.80.00 - DOWNGRADE.gz.bin - everything is just like in a book.
2. "Restored" IMEI. Checked through the ati command.
3. I requested BV7R2C0update_21_316_01_00_07_Telia_AT_MODWEB_TTL64.gz.bin with a fix. TTL.
4. Received equipment mode ............ And further - a stopper, unlikemichael.lvf . Rollback to the service 21.282.99.80.00 does not occur. The firmware version does not change.
5. The RESET button does not respond.

I ask for a help ...

Post has been editedDemiurge67 - 20.05.19, 13:49



Rep: (312)
Pigovina @ 05/15/19, 10:55*
Beeline, in principle, bottom speed, even with a "triplet"

Stable 50-60 in the afternoon, up to 100 nights. MTS, where I live and work, has already slipped into the disgrace of 30-40.



Rep: (59)
* vipost,

Where are you with your recovery instructions? Here, the newly made owner of the Trouble!

Posted on 05/15/2019, 19:26:

* Demiurge67

Write in a personal vipost. He posts like he found a solution.



Rep: (83)
Pigovina @ 05/15/19, 10:55*
Beeline, in principle, bottom speed, even with a "triplet"
Russia is big and Moscow is not exhausted. So at least a rash statement: happy:
In my places, Beeline is not the best, but the second after Megaphone, MTS with tariffs rolled into a deep anus, here I agree with the fireman. Barely 2 - I don’t even remember, at the same time in some Chelyabinsk, he may number 1 with someone

Posted on 05/15/2019, 22:39:

Demiurge67 @ 05/15/19, 16:44*
The result of many hours of action is almost similar to the result of comrade michael.lvf:
With a shudder, I recall the process of flashing this box. Greater "red-eyed" I have not experienced. A very stoker helped me then. Some comrades, in principle, could not flash this megaphone 300 in any way, here, too, was in the subject



Rep: (39)
Michael.lvf @ 05.16.19, 00:35*
Greater "red-eyed" I have not experienced.

Michael.lvf @ 05.16.19, 00:35*
flash this megaphone 300

I do not consider myself to be witty-headed (read "The Adventures of Gulliver") ... But I cannot attribute myself to dumb-headed. In my conscience, there are several firmware for the Chinese Galaxy S3 clones. And not the worst, however. But I am not able to defeat this device ... I DO NOT UNDERSTAND !!!! I don’t understand the logic - why in one case it is necessary to clamp the buttons before flashing, in another - it is not necessary. I don’t understand why in one case it is necessary to wait for 6 cycles of loading the firmware, in the other one is enough. I do not understand why EVEN according to the instructions DOWNGRADE does not occur. Although it should happen .... And the worst part ... The device stopped responding to HARDWARE reset !!! To tell. that I’m shocked is nothing ...

Posted on 05/15/2019, 23:11:

The instruction from the header for restoring ushatnykh routers (Power + WiFi is on) is not correct.

Judging by my torment - it is likely.
The problem is reproducible, and can be solved (relatively) easily,).

AS???



Rep: (312)
why in one case you need to clamp the buttons before flashing, in the other - do not
When you sew a lowering - you need to pinch. When you roll the final one over it, it is not required. The first time I also stupid: D The second already figured out.

why in one case you have to wait 6 cycles of loading the firmware, in the other one is enough
Anyway, I was waiting for about 10-12 “passes”. The light bulb, if everything is right, starts blinking, in my opinion, with a mauve color. Sewed six months ago - I do not remember already: blush:

why EVEN according to the instructions DOWNGRADE does not occur
I suspect - as I, at first, do not grasp the moment when you need to release the buttons. There, in general, a moment is simple, tenths or even hundredths of a second after pressing the “rocker” of power.



Rep: (39)
Aircraft stoker @ 05/16/19, 01:23*
When you sew a lowering - you need to pinch.

Not a damn thing. (Sorry for naturalism)
Aircraft stoker @ 05/16/19, 01:23*
When you roll the final one over it, it’s not required

This contradicts the instructions from the header -
RECOVERY from the mode with POWER and Wi-Fi indicators on
Aircraft stoker @ 05/16/19, 01:23*
The first time I also stupid: D The second already figured out.

Avon, what is your intelligence .... Today I’m 150 times in different variations ....



Rep: (312)
Demiurge67 @ 05/15/19, 11:30 p.m.*
This contradicts the instructions from the header.

No, it does not contradict. Restoring from the "power + wifi" mode is not the firmware of the final software.

Demiurge67 @ 05/15/19, 11:30 p.m.*
Avon, what is your intelligence .... Today I’m 150 times in different variations

Meant - with the first router. And stupid as well. 20-30 times on the first day, then on the second as many, probably. All the locals in the drug got sick of it: D Here somewhere lies my message, similar to yours: everything is wrong, etc.

Post has been editedAircraft fireman - 15.05.19, 23:35



Rep: (39)
Aircraft Fireman @ 05/16/19, 01:33*
No, it does not contradict. Restoring from the "power + wifi" mode is not the firmware of the final software.

Well then ...We read:
5) Now we flash the working firmware, for example, 21.306.01.00.00 using the Multicast Upgrade Tool program with a checkmark next to Force Upgrade.
To do this, simultaneously hold down the WIFI and WPS buttons and turn on the router. As soon as the WiFi light flashes briefly, immediately release the Wi-Fi button and after another 3 seconds release the WPS button.
The firmware upload process will begin. We are waiting for a minimum of 6 full passes "Package file send time" in the Multicast Upgrade Tool program and when there are already 7 passes or higher, click Stop.

BUThere - otherwise:
3) Now we flash the working firmware (select it, the one you want to flash) using the Multicast Upgrade Tool with the checkmark next to Force Upgrade.
To do this, click Start in this program and turn on the router.

Today in the morning I already two times (fresh mind) tried to alter the animal. The result is the same. Rollback to service firmware does not occur. The reset button does not work. The router is in CFE mode.
Does anyone have any thoughts?
Aircraft stoker @ 05/16/19, 01:23*
The light bulb, if everything is right, starts blinking, in my opinion, with a mauve color.
And what is the modification of your router? Can I ask for a photo of the sticker under the cover below? Serials and have, of course, paint over.

Post has been editedDemiurge67 - 16.05.19, 08:41



Rep: (12)
Hello to all.
My momed is still going, but the forum is slowly smoking.

ATP to everyone who tortured the animal and wrote guides: yes2:

Demiurge67 in CFE, after all, can you try to flash it, or not?



Rep: (39)
The victory was inevitable, as demob in May!
It turned out a lot of flooding, hid under the spoiler.
I do not know how, after 100,500 attempts to follow the instructions for restoring the firmware (ie, the beginning of the firmware - with the buttons pressed), but I finally jumped on the Tele2-Sweden firmware (BV7R2C0update_21.316.01.00.56 - Tele2 - LATEST.gz .bin). At the same time, I have never managed to fill in the "service" firmware BV7R2C0update_21.282.99.80.00 - DOWNGRADE.gz.bin.
Attached Image

Next, I will log "in real time."
Got just such a webmord, two languages ​​and the lack of internet. Moreover, if you hover over the signal strength indicator, the type of connected network is displayed (in my case, LTE2600). Perhaps these are the intrigues of TELE2, who recognized the router with a phone SIM card, but I don’t want to find out.

After that, I flashed my native Huawei firmware BV7R2C0update_21.306.01.00.00 - Original Huawei.gz.bin

Attached Image

Got just such a webmord, eleven languages ​​and the Internet. Apparently, in the previous case it was the fault of the firmware.
Of the minuses - objectively lean menu. When hovering over the network indicator, 4G is displayed without indicating the range.
What is significant - the firmware version did not change, although it is obvious that the firmware is different!

And then - all the wonderful and wonderful! I stitched "through" (because the firmware version checked via the ati command does not change, but the webmord disappears) "this", this is a "teether" firmware BV7R2C0update_21.282.99.80.00 - this is the "testimonial" firmware version of the BV7R2C0update_21_316_01_00_07_TetaEGRO.gz.bin OTTGRE. And - Oh MIRACLE !!! I am the FIRST (!!!) that .... however - see the screenshot. In the foreground - what was stitched; in the background - what was sewn.
Attached Image


A miracle happened! What I did - I got it - I mean the firmware version on the webmord.
Attached Image


And, finally - the second thing happened. I sewed with fix. TTL, which, in fact, wanted.
Attached Image

The question is what was it? As an answer, NVRAM lacked any records - because I also dug in this direction, loading two tables - exemplary and from the router to Exel and sorted.
Attached Image

But not all the values ​​were saved after the reboot.

ZY The Finns have a fresh firmware Elisa (Finland) \ BV7R2C0update_21.318.01.00.260.gz.bin. Is it possible to make a mod on its base?

All good!


Full version    

Help     rules

Now: 09/06/19, 9:43 p.m.