[X]Assistant

[Wedel]

BlackBerry Passport - Firmware
_SQW100-1
Description | Discussion >> | BlackBerry OS FAQ | BBM Groupsavagemessiahzine.com >> | Blackberry club >> |

• All Forum Rules are valid in the subject.savagemessiahzine.com
  
• Before posting photos, read the topic Working with Images on the forum
  
• Messages that are not related to the topic of discussion (offtopic) are deleted without warning.
  
• Before asking a question, use the search.
  

Download firmware(autoloader) canhere(thanks for the linkWedel)

BLITZ (for installation without data loss) - here(latest version 10.3.2789)

Alternative download link

Instructions for flashing autoloader

If, for any reason, you need to flash your BB10 using an autoloader, use the following instruction:

1. make backup via Blackberry Link (6)
2. Close Blackberry Link, making sure that the backup is made.
3. disconnect the phone from the computer and turn it off (1)
4. extract the autoloader from the archive (if necessary) - as a rule, the autoloader itself is archived in .rar, .zip or .7z
5. run autoloader - file with .exe extension
6. when Connecting to Bootrom appears, connect the phone to the computer (2)
6.1. if a password is required, enter the device password and press the Enter key
7. The green LED will light up - the installation of the firmware will start (3)
8. after the firmware is completed, the phone will start to boot - you can disconnect it from the computer
9. after initial setup, restore from backup (not recommended), or set up as a new device (4) (5) (6)

(1) remove the battery if the phone can not be turned off (error when updating, backup, resetting, etc.)
(2) remove the battery, if instead of the firmware (green LED), the normal boot process begins, and reconnect the phone
(3) if you removed the battery, insert it after the start of the firmware process
(4) recommended if the firmware version was installed, different from the one on which the backup was made, or you made the firmware to get rid of any problems with the device or software
(5) for full operation of all services (including BBM Channels, Video / Voice) it is recommended to flash and make the initial setting as follows:
initially choose English. UK / USA language and region;
Do not enter the BBID during the initial setup process (for OS 10.3.2 - you must disable BlackBerry Protect in the phone settings before installing the autoloader)
do not include the location;
configure all the necessary parameters after the initial setup (setup).
(6) if you want to save data from your device as much as possible, but to get rid of problems that will inevitably return after restoring from a backup made via Blackberry Link, you can backup data using an application like Ultimate Backup for BlackBerry 10, saving the data to memory card, or in the cloud, and then restoring them to a clean device.

Instructions for installing firmware without data loss

1. Download Blitz - archive in ZIP format;

2. Connect the phone to the computer;

3. Run Sachesi (we need the latest version withhttps://github.com/xsacha/Sachesi/releases)and open the tab "Installation";

4. Do not forget to select the item "Install only new versions";

5. Drag and drop the ZIP archive onto the list where the applications installed on the phone are displayed. Archive unpacking and installation will begin;

6. We are waiting for the end of the installation;

7. Restart the phone if it does not happen automatically;

8. We are waiting for the reboot to finish.

Instructions fromhttp://www.blackberrys.ru/ (permission to post is obtained)

M

There is no curator in the subject. If there is a user in the subject who wants to become a Curator and the correspondingRequirements for candidates, he can apply in the topicI want to be curator(after having studied the topic header and all materials for curators).
Prior to the appointment of the curator, on filling caps, please contactmoderatorssection through a buttonunder the messages to which you want to add links.

Post has been editedklich007 - 31.10.16, 15:57

[Wedel]

muza9,
Not mandatory, but for the purity of the installation it is necessary to do a wipe. There will not be a glitch, many similar examples in the history of flashing.
Vip did, the device turned off, launched the autoloader, connected the cable, the firmware process will begin. Everything.

[muza9]

Wedel @ 02/10/2015, 14:11

Everything.

There is no explicit indication to "turn on" the machine ...
Turn on the cable itself? or simply did not say the type itself implied?

[Wedel]

muza9,
Yes, when the cable is plugged in, the device will activate and switch to the firmware mode (the green LED will light up)

[muza9]

Wedel @ 02/10/2015, 12:45

Put, the flight is excellent.

But the muse has caught its first brick ... After the end of the firmware (green diode) the device did not turn on and flashes red point-point-pause-point-point-pause ... it has been 5 minutes already and does not respond to the button.
As I understand it, this is an explicit and unequivocal indication that “Bobby is dead” and it is necessary to change it to the previous one?

I want to think that it just turned out to be a broken archive file, because during the download (the office) there were some unpleasant stops and speed drops to zero ... the people populated the channel with all their gadgets.

And CRC-files on gigabyte archives in our community, as I understand it, it is not customary to attach? In vain ...

Now I will try to re-download.

[Wedel]

muza9,
I did not distribute.
Did Vip do before flashing?

[muza9]

Wedel @ 11.02.2015, 05:17

Did Vip do before flashing?

The first time is no. I have nothing there yet, just a few sound-color settings ...

After the first failure, I rolled back to 2072, pumped over the autolod 2267, and again repeated the flashing, but already pedantically, with cleaning.

But it still does not work: the protocol on the PC is fine, but as a result, at the end of the procedure, the device endlessly blinks red dot-pause ... and does not respond to the button.

Back to 2072, it is changed quietly and works at the end, as it should be - switching on and loading ...

[Wedel]

muza9,
There is content or no content, but WIPE is needed.
Autoloader in the archive, he unzipped without any problems? For many did not have similar problems, including me.
Miracles do not happen, you have to dig in a different direction, different from the firmware file.

Option to try: Make a wipe, turn on the body, the first dialog box appears, do nothing. Run the firmware file, and go.

[muza9]

Wedel @ 11.02.2015, 09:13

Make a wipe

Then, perhaps, I could not do it right. So how should it be?

Wedel @ 11.02.2015, 09:13

Autoloader in the archive, he unzipped without any problems?

Yes, good. Compared byte-by-byte - it coincided with what I downloaded earlier ...

Once again, in steps:
1 cleaning device
2 turn off the device,
3 launch of autolod on PC,
4 connecting the switched off device to a PC with a cable,
5 firmware with green indication and process indication on PC
6 further (if everything is OK) self-switching and testing the device ...
So?

[Wedel]

muza9,
Settings - Security - Delete data. Be sure to wait for the end of the process.

Point by point, yes, that's right.

[muza9]

Well, I do not know ... therefore - it is not the fate of the muse to be with this firmware, I will wait for the next release.

I downloaded the third time, disconnected the Locker on the PC, erased the device, flashed it ...
And I get the same result: after the firmware, the device did not turn on, but began to blink point-to-pause with a red diode ...

Return on 2072.

[Tymnev]

Muza9 @ 11.02.2015, 08:54

But it still does not work: the protocol on the PC is fine, but as a result, at the end of the procedure, the device endlessly blinks red dot-pause ... and does not respond to the button.

either the radio module software is not native, or the wrong archive was downloaded .... but in general there is an optimized official version of 1955 for the passport for today the best of 10.3.1 .... I inform the objector that all the firmware was used personally (1016,1151,1154, 1298,2072,1949,1955,2243,2267) ..... the only thing that updated 62 bars of a more recent version from 2267.

[Wedel]

Tymnev
Dooooo))) is not native ... with a thousand passports already on it ....: - D

[muza9]

I did not have to say: do you need to remove the memory card and SIM card from the device before flashing it?

[Wedel]

muza9,
Not necessary

[Wedel]

Perezal on Cloud Mail.ru
Autoloader 10.3.1.2267

Posted 02/14/2015, 14:28:

muza9,
Well, how is success with the flashing?

[muza9]

[email protected], 14:28

Well, how is success with the flashing?

Thank you, with your option I am boring ...
True, this version still did not solve my problems.

[muza9]

Companions!
Is it possible to somehow disable the "school" or bypass it and not pass these "lessons" after each firmware?

And then after the third time, this is somehow not interesting, and time is a pity ...

Thank.

[Wedel]

muza9,
I'm afraid not....

[muza9]

Sadists ... But, on the other hand, there is one more incentive not to give up with flashing, but to be more solid.

[Wedel]

Autoloader 10.3.1.2243
SQW100-1 Cloud Mail.ru

as an option to try.