Assistant
REPLY |
TP-Link WR1043nd - Discussion | [wifirouter] Discussion of all versions (v1 - v3) of the router |
Message#1 16.10.14, 14:05 | |
Guru [offline] Group: Moderators Messages 14788 Check in: 04.05.09 Apple iPhone 7 Reputation: 1720 | TL-WR1043ND - Discussion A photo v1 v2 Description v1
v2
Specifications TP-link_TL-WR1043ND_v1.x TP-link_TL-WR1043ND_v2.x TP-link_TL-WR1043ND_v3.x v1 Hardware Interface
Standards of wireless data transmission IEEE 802.11n, IEEE 802.11g, IEEE 802.11b 3 dBi antenna * 3 removable omnidirectional antennas (RP-SMA connector) Dimensions (WxLxH) 200 x 28 x 140 mm Parameters of the wireless module The frequency range of 2.4-2.4835 GHz Signal transmission speed
Sensitivity (reception)
Wireless Security 64/128/152-bit WEP / WPA / WPA2, WPA-PSK / WPA2-PSK Wireless network 64/128/152-bit WEP / WPA / WPA2, WPA-PSK / WPA2-PSK Software features WAN connection type Dynamic IP address / Static IP address / PPPoE / PPTP (Dual Access) / L2TP (Dual Access) / BigPond DHCP Server, Client, DHCP Client List, Address Reservation QoS (traffic prioritization) WMM, Bandwidth Control Port Forwarding Virtual Server, Port Launch, UPnP, DMZ Dynamic DNS DynDns, Comexe, NO-IP VPN PPTP, L2TP, IPSec (ESP Head) Access control Parental control, local control control, list of nodes, scheduled access, rule management Network security (firewall) Protection against DoS attacks, SPI firewall, filtering by IP address / MAC address, domain name, IP binding and MAC address Control
CE, FCC, RoHS certification Contents of delivery
Environmental parameters
v2 Hardware Interface
Standards of wireless data transmission IEEE 802.11n, IEEE 802.11g, IEEE 802.11b 5 dBi antenna * 3 removable omnidirectional antennas (RP-SMA connector) Dimensions (WxLxH) 225 x 141 x 30 mm Parameters of the wireless module The frequency range of 2.4-2.4835 GHz Signal transmission speed
Sensitivity (reception)
Wireless Security 64/128/152-bit WEP / WPA / WPA2, WPA-PSK / WPA2-PSK Software features WAN Connection Type Dynamic IP Address / Static IP Address / PPPoE / PPTP (Dual Access) / L2TP (Dual Access) / BigPond DHCP Server, Client, DHCP Client List, Address Reservation QoS (traffic prioritization) WMM, Bandwidth Control Port Forwarding Virtual Server, Port Launch, UPnP, DMZ Dynamic DNS DynDns, Comexe, NO-IP VPN traffic pass PPTP, L2TP, IPSec (ESP Head) Access Control Parental Control, Local Management Control, Node List, Scheduled Access, Rules Management Network security (firewall) Protection against DoS attacks, SPI firewall, filtering by IP address / MAC address, domain name, binding by IP and MAC address Control
CE, FCC, RoHS certification Contents of delivery
Environmental parameters
useful links Catalog of official firmware TP-link TL-WR1043ND official with cut out boot for TP-Link TL-WR1043NDv3 DD-WRT r25697 for TP-Link TL-WR1043NDv1 (22.12.14) DD-WRT r25697 for TP-Link TL-WR1043NDv2 (22.12.14) OpenWRT - firmware and most detailed wiki (eng.) Firmware WR1043ND v1 OpenWrt Attitude Adjustment 12.09 r36088 (v5) from yohimba Gargoyle - firmware and wiki (eng.) | crutch for DNS on the gargoyle Gargoyle Firmware (Gargoyle) Gargoyle TP-Link WR1043nd v1 FAQ TP-Link WR1043nd v1 router review on 3DNews TP-Link router overview WR1043nd v1 on Overclockers.ru Reassigning WAN port to LAN Transition to official firmware for TP-LINK routers with DD-WRT Instructions for the restoration of TP-Link TL-WR1043ND v.1 Expansion of the system section OpenWrt Barrier 14.07 on the firmware from gwlim WR1043ND v1 OpenWrt Barrier Breaker 14.07 r45620 firmware from gwlim Setting up an OpenVPN server OpenWrt for sabzh v.3 How to return the official firmware on TL-WR1043ND_v1 with OpenWRT Method of getting Dual Access on gargoyle firmware Using the alternative Breed loader (v.833). Fast-Path-LEDE-OpenWRT for v.1 v.2 v.3 v.4 and ath79-builds for v.1 v.2 v.3 v.4 Password reset English version of the stock firmware BETA TL-WR1043ND_V3_160713 from 2016-08-09 RESTORATION TL-WR1043ND from brick state Post has been editedstp101 - 05.02.19, 20:26 Reason for editing: TL-WR1043ND RECOVERY from brick state |
Message#2 26.03.14, 01:26 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | I installed the optive version of the router v.2 OpenWrt firmware on TP-Link 1043ND and everything seemed to be set up fine, but after rebooting the web interface stopped working! I installed the firmware from this site:http://wiki.openwrt.org/toh/tp-link/tl-wr1043nd 192.168.1.1 pings and can be accessed via Telnet! But what commands do I need to enter to set up the Internet or enable the web interface, I don’t understand ?! I also found an article on how to roll back to the factory firmware, but the problem is that you need to have a configured Internet on the router! http: //www.starblazer...AME=...692#message6692 and the samehttp://forum.ixbt.com/..?idid1441517:2131#2131 Maybe you can specify a folder on your computer where the factory firmware is and download from it? Post has been editedKVN777 - 26.03.14, 01:28 |
Message#3 26.03.14, 18:15 | |
Cnccoder [offline] Group: Friendssavagemessiahzine.com Messages 826 Check in: 09.01.11 Vertu Ascent Ti Damascus Steel Reputation: 104 | KVN777, if there is a firmware from a trunk, then there may not be a web interface (luci), you can put it offline http: //wiki.openwrt.or...owto/luci.essentials? s or configure network settings via winscp console, putty to help there where the firmware was taken below is the manual for rolling back to the original firmware, just read carefully otherwise zakirpichite -------------------- |
Message#4 26.03.14, 23:50 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | thank you for not ignoring .... tried to flash through ftp, got a reboot. Tomorrow we will try to reflash through sirial port, I will write off what happens ....) |
Message#5 28.03.14, 11:06 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | Hi, the router was stitched only with OpenWRT firmware from the developer's site. again came across a problem, after the first login you need to put a password. I enter "passwd" writes enter the new password, but the characters in the line are not typed what to do ...? can anyone help |
Message#6 28.03.14, 11:10 | |
Cnccoder [offline] Group: Friendssavagemessiahzine.com Messages 826 Check in: 09.01.11 Vertu Ascent Ti Damascus Steel Reputation: 104 | Characters are not displayed, so it should be -------------------- |
Message#7 28.03.14, 14:27 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | In SSH, the web interface is not installed, I do not understand how to install offline. |
Message#8 28.03.14, 15:57 | |
Cnccoder [offline] Group: Friendssavagemessiahzine.com Messages 826 Check in: 09.01.11 Vertu Ascent Ti Damascus Steel Reputation: 104 | KVN777, study what packages are needed herehttp: //wiki.openwrt.or...owto/luci.essentials? sMinimalistic offline installation swing them from herehttp: //downloads.openw...trunk/ar71xx/packages/on a computer, using winscp, transfer them to a router, for example in / tmp / luci go through putty to the router and install them, so opkg install /tmp/luci/liblua_5.1.5-1_ar71xx.ipk liblua_5.1.5-1_ar71xx.ipk is for example, and so everyone is possible and all together through & p.s.this is a branch for developers, packages have been updated today, there may be incompatibilities Post has been editedsneres - 28.03.14, 20:34 -------------------- |
Message#9 28.03.14, 20:35 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | How to find the package you need to download for this version of the firmware. there are too many of them ... ( |
Message#10 09.04.14, 18:06 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | problem solved, special thanks to "sneres". I think the topic is closed. |
Message#11 27.04.14, 23:46 | |
Visitor [offline] Group: Active users Messages 27 Check in: 06.04.11 LG Optimus 4X HD Reputation: 0 | Good day! The same situation as with KVN777 has happened! After the firmware of the router, OpenWRT does not enter the web interface, although telnet and ping pass! Please tell me how was the problem solved! |
Message#12 27.04.14, 23:49 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | Hi, The interface components were manually downloaded and installed. |
Message#13 27.04.14, 23:51 | |
Visitor [offline] Group: Active users Messages 27 Check in: 06.04.11 LG Optimus 4X HD Reputation: 0 | And there is no list of these components! and then rummaged through a bunch of things and so did not understand which of these things to choose? |
Message#14 27.04.14, 23:57 | |
Visitor [offline] Group: Active users Messages 17 Check in: 21.01.10 Samsung Galaxy Spica GT-I5700 Reputation: 1 | that's what I was advised: sneres need original firmware without boot rename it for example intplink.bin, you throw it in a folder/ tmp and write in putty mtd -r write /tmp/tplink.bin firmware hereexileOn this piece of iron they are discussing there and there is a firmware without boot here is the minimum that you need to install liblua lua libuci-lua libubus-lua uhttpd luci-lib-ipkg luci-i18n-english luci-sgi-cgi luci-lib-core luci-lib-nixio luci-lib-sys luci-lib-web luci-proto-core luci-theme-base luci-theme-openwrt luci-mod-admin-core luci-mod-admin-full Post has been editedvadim_1984 - 14.11.14, 09:58 Reason for editing: beauty brought |
Message#15 16.10.14, 12:57 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 62 Check in: 24.01.13 Google galaxy nexus Reputation: 1 | TL-WR1043ND how to set up so that it automatically changes, one connection to another, (that is, there is a tariff access and not a tariff. But the speed limit is 2, the first after an hour of the night is anlim at speed standards) how to make it so he automatically switched to another connection. |
Message#16 16.10.14, 15:22 | |
Guru [offline] Group: Moderators Messages 14788 Check in: 04.05.09 Apple iPhone 7 Reputation: 1720 | how to set up so that it automatically changes, one connection to another Do you have two different "Internet" in the apartment comes 2 lace? The modem has only one wan port, I don’t think that it can be configured this way: scratch_one-s_head: -------------------- |
Message#17 16.10.14, 15:32 | |
a guest [offline] Group: Users Messages 2 Check in: 16.10.13 LG G2 Reputation: 0 | people! Is this unit suitable for a 3-room apartment? Post has been editedmafia9111 - 16.10.14, 15:34 |
Message#18 16.10.14, 15:39 | |
Guru [offline] Group: Moderators Messages 14788 Check in: 04.05.09 Apple iPhone 7 Reputation: 1720 | |
Message#19 16.10.14, 19:33 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 62 Check in: 24.01.13 Google galaxy nexus Reputation: 1 | [email protected], 14:22 Do you have two different "Internet" in the apartment comes 2 lace? The modem has only one wan port, I don’t think it can be configured How to make it so that you do not constantly go into the settings and do not change the user. you can automate it like that. using a script or something else Post has been editedRurouny - 16.10.14, 19:44 |
Message#20 16.10.14, 22:07 | |
Guru [offline] Group: Moderators Messages 14788 Check in: 04.05.09 Apple iPhone 7 Reputation: 1720 | -------------------- |
Message#21 31.10.14, 20:24 | |
Visitor [offline] Group: Active users Messages 17 Check in: 03.12.13 Reputation: 1 | There is a desktop PC and two laptops (2-room flat). Is it possible on this model to distribute the speed of traffic between them ... well, for example, 3 Mbit / s per each? sek.kakoy section of the router settings need to open? |
mobile version | Now: 04/28/19, 22:41 |