Assistant
REPLY |
The car stereo does not see the gps sd card | the car radio files {exe} does not see |
Message#1 13.02.14, 01:03 | |
a guest [offline] Group: Users Messages 1 Check in: 13.02.14 Reputation: 0 | Hello! I really need help in solving. there is a radio with gps navigator unmarked. HMI: SW010.11 05.13.27.16.41-HanStar MCU: LT 001.120621 DVD: VG013YJan312013 NKV: A4.10.2013.5.27.16.46 Btv: CL130725 the service menu is opened by pressing HMI-MCU -DVD On the radio, all functions work except the gps navigator (stubbornly does not want to see the gps micro sd card). Cards have been tried different from 2 GB to 4 GB and different manufacturers. Navigation programs are also different, Navitel, about the city, Citigid, seven roads. None of the listed executables open. There was a suspicion of a faulty gps micro sd card reader. disassembly method has been established the following All contacts from inside the card reader to the board are called at all points of the loop .... under the microscope inside the card reader everything is in place, the contacts are all intact. I do not know how to enter the menu Photo device: attached maybe someone already faced a similar problem. what to do in this case. thank you very much! |
Message#2 23.02.14, 15:17 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 129 Check in: 09.04.13 Reputation: 6 | many interpreted solutions were hardly found and abandoned. Apparently, on the map, besides the executable of the navigation program, there must be something else, some system files, so it does not see it. If you someone with the same device will drop the contents of the card, then maybe be run. |
Message#3 12.04.14, 04:11 | |
Experienced [offline] Group: Friendssavagemessiahzine.com Messages 438 Check in: 16.11.13 Reputation: 35 | Most likely the device does not accept SDHC cards try pure SD. Of course, there is a big deficit to find cards on 4G maximum, which are SD cards. Slightly easier to find 2G. -------------------- Grant Suite 21902-42-11 2013 Guards, 219020-42-024 2015 Guards. |
Message#4 17.04.14, 09:42 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 132 Check in: 23.10.13 Lenovo P780 Reputation: 4 | And what file system on the card was used? This may also be one of the reasons for the card's “invisibility”. |
Message#5 17.04.14, 10:54 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 154 Check in: 03.04.13 Xiaomi redmi Reputation: 10 | You seem GU company Lsq STAR I have the same entries in the settings If you have a gps micro sd card reader, then you are most likely not trying to install the assembly. I had a couple of times when after you insert a card, and he does not see it. Try inserting a memory card, then turning off and then turning on the radio. ZY 99% you are not trying to run your build. ZY Try again to check the parameters of the state program PortTool To do this, on an empty card, drop this program and change the name in the file itself to Navitel.exe Then insert a micro sd gps into the card reader and turn on the radio. The file is launched simply by pressing the Navi button. -------------------- Possess "shchudom" Xiaomi MiTV2 TV |
Message#6 28.08.14, 08:55 | |
Old resident [offline] Group: Friendssavagemessiahzine.com Messages 732 Check in: 22.03.12 Xiaomi Redmi 5 Plus 4/64 Reputation: 47 | I have such a problem - the files disappear. I copied the Navitel directory with files to the card, pasted it into the GU, it sees the directories, there are no files ... it turned out that all the files disappeared somewhere: shok: What could be the problem? GU China. OS: VERSION AT 551 00 2013 07 22 (CS4344) APP: VERSION 05 1103 02 2012 10 24 -------------------- ASUS VivoWatch BP (HC-A04) |
Message#7 25.10.14, 10:40 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 103 Check in: 27.12.11 Reputation: 1 | 2-din cassette recorder from China wince 6, before installation checked everything works. The next day after installation, I decided to turn on the navigator and I also jumped out "no GPS card". Who solved the problem? or scored? |
Message#8 05.11.14, 10:37 | |
a guest [offline] Group: Users Messages 6 Check in: 26.04.07 Asus MyPal A636N Reputation: 0 | I had a similar situation, only the map appeared with a ratio of 1 appearance and 500 reboots. He did a lot, formatted cards, changed the type of cards (it is obvious that cards are needed up to 4 GB and not hc). In the end, everything was decided by re-soldering the memory slot, the operation is complicated and very few people fit in to solder the Chinese miracle, so for 500 rubles. Not sure it's going to happen. |
Message#9 10.11.14, 18:56 | |
a guest [offline] Group: Users Messages 2 Check in: 10.11.14 Reputation: 0 | [email protected], 10:37 In the end, everything was decided by re-soldering the memory slot, the operation is complicated and very few people fit in to solder the Chinese miracle, so for 500 rubles. Not sure it's going to happen. Can you give more details? Please tell that where to solder. Preferably shemku, and better photo report. |
Message#10 09.03.15, 13:09 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 103 Check in: 27.12.11 Reputation: 1 | above wrote about the same problem as the author. I was in shock when, after a long trip (about 4 hours), when the cabin was very well heated, instead of the radio button, I missed and clicked on the navigation and it started. After testing for a month, I came to the conclusion that it works exactly when it is warm, it does not start after the night either, after it’s hot in the cabin, it works, and noticed that when it’s already warm, it seems that it’s still on the splash screen or just on card, having waited a bit and restarting starts working again. Now I think the reason is in the slot or in the gland inside the radio? |
Message#11 24.04.15, 05:04 | |
a guest [offline] Group: Users Messages 9 Check in: 21.10.09 Reputation: 0 | Twice soldered. There, the board with the reader in the slot of the front panel board is soldered to the pad at the edges of the boards at 90 °. First, the map disappeared. Opened, I see one not drunk. Soldered, earned. In the car again disappeared completely. Brought home, began to look, and there the paths were torn. Shunted MGTF-ohm (PTFE insulation wire). Lead-out areas of the vias. In short, everything works. We need non-frustrating hands (they are shaking me) and the soldering iron is short and small, well, and when assembling, make sure that the loops are not raised. ;) -------------------- Redmi 5 Plus, Newsmy Carpad duos, Supra STV-LC50ST4000U |
Message#12 24.04.15, 08:29 | |
Visitor [offline] Group: Active users Messages 20 Check in: 19.12.09 Reputation: 0 | And the train can fly too? disliking built-in uncomfortable with them |
Message#13 03.05.15, 13:35 | |
Visitor [offline] Group: Active users Messages 16 Check in: 28.06.08 Blackview a8 Reputation: 0 | [email protected], 05:04 Twice soldered. There, the board with the reader in the slot of the front panel board is soldered to the pad at the edges of the boards at 90 °. Receiver externally one to one. I decided to repair it today. Trailing loops did not help. Plus, miniUSB broke, fixing the board. In short, after soldering a card with a reader, the GPS greeted happily. : Thank_you: Straightened the microphone to the heap, it was turned sideways. But it is sad to solder! o.O |
Message#14 10.06.15, 13:27 | |
Visitor [offline] Group: Active users Messages 25 Check in: 07.11.13 Reputation: 3 | |
Message#15 11.07.15, 05:40 | |
Visitor [offline] Group: Active users Messages 25 Check in: 07.11.13 Reputation: 3 | Good day! It was possible to launch Navitel 3.5.0974, the download file NaviOne.exe, but there are no maps in demo mode. Other programs are not installed. Tell me how to install 7 roads instead of Navitela. |
Message#16 25.08.15, 08:52 | |
a guest [offline] Group: Users Messages 1 Check in: 10.03.12 Sony Ericsson Xperia neo Reputation: 0 | Good day! I also encountered a problem: the Chinese GU does not see microSD with navigation. Displays the message "Invalid SD card". 4 GB card, formatted in FAT32. I have a question: can I still see the files on the map through the GU? except via GPS path & |
Message#17 05.11.15, 12:42 | |
a guest [offline] Group: Users Messages 1 Check in: 13.10.15 Reputation: 0 | [Attachment = "7050419: image.jpeg"] Good day to all! I do not see the same problem with a GPS map, but not everything does not see the Internet stick either, tell me what can be done, can anyone come across this. And of course, here is my miracle. Post has been editedAlexander197070 - 05.11.15, 12:47 |
Message#18 06.11.15, 10:00 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 76 Check in: 19.12.08 Reputation: 8 | I do not see the same problem with a GPS map, but not everything does not see the Internet stick either, tell me what can be done, can anyone come across this. problem with the slot, it may need to be replaced, the simplest way to check is to carefully unscrew the instrument's face with the screen from the box; the one with the screen) to the DVD drive, and the GPS is located on the same board (the one with the screen) as an adapter ..... WE DO REPLACE and try launching the navigation from the SD slot. Then you can drive or repair the GPS slot if everything works after the substitution .. I tried to paint with simple slang .... |
Message#19 19.11.15, 10:31 | |
a guest [offline] Group: Users Messages 9 Check in: 18.07.13 Samsung Galaxy Note 10.1 Reputation: 0 | When the device does not see the memory card, the fault is 99% in poor soldering of the memory card slot. It is necessary to disassemble and heat the soldering iron all 7 (as I recall) tracks. Payal first 2. There were cracks. Need shaking hands, as correctly stated above. I asked my wife for the first time to solder, she knows how. Then I had to disassemble a month later, and the rest to disappear. :) If you do this in a scrap, then in the slot where the USB modem is inserted, you need to insert a USB splitter, and connect a memory card and an Internet modem (if you need one) to it. Post has been editedanndd - 19.11.15, 10:35 |
Message#20 29.04.16, 06:19 | |
a guest [offline] Group: Users Messages 9 Check in: 18.07.13 Samsung Galaxy Note 10.1 Reputation: 0 | He did the soldering as he wrote above in 2014. Spring 2016. Again, he does not see the micro sd card. Those. then sees, does not see. Soldered one track. The same thing started soon. I think the connector. Itself is not useful. Drove to the repairman by phone. He pulled this board out of mms, looked under his microscope, a little said soldered the tip of the case. While working, if that - said to change the nest itself sd. Even the guy did not take the money. All the same, techies are not merchants! I tried to work through the hub-hub: sd card and usb modem in one slot. It works, only slower. Probably because of the hub. Not very much. If you only need a navigator, without the Internet, then without a hub is normal. Post has been editedanndd - 29.04.16, 06:23 |
mobile version | Now: 04/29/19 13:42 |