[X]Assistant

[Dymon]

ASUS MeMO Pad - Firmware
ME 172V
Description | Discussion | Firmware

Drivers and Utilities

Firmware

Alex_ROM
ASUS ME 172V WW 4.5.4
AMPC Mini Rom

Instructions

How to make a hard reset
Ruth and Recover
Ruth
Tablet recovery
Another way to recover.

Post has been editedvaalf - 29.09.16, 15:20

Reason for editing: Another way to restore

[mr.bin]

How to make a hard reset

Download and unzip the contents of this archive to a microSD card.
cleardata.zip(15.5 MB)

Insert the card into your device in the off state.
Turn on the machine.
Select with the help of the volume rocker ClearUserData.
Confirm with the power button.
Upon completion, the program will ask you to remove the memory coil and automatically restart the tablet in a few seconds.

Post has been editedmr.bin - 14.06.13, 17:44

[Semenov1910]

How to make a hard reset

Download and unzip the contents of this archive to a microSD card.
cleardata.zip (15.5 MB) Download count: 1

Insert the card into your device in the off state.
Turn on the machine.
Select with the help of the volume rocker ClearUserData.
Confirm with the power button.
Upon completion, the program will ask you to remove the memory coil and automatically restart the tablet in a few seconds.

My recovery did not start until I pressed the volume + button.

[mr.bin]

Firmware ASUS ME172V WW 4.5.4
http://dfiles.ru/files/dy0ki0ios
Download and unpack the contents of this archive on a clean MicroSD card while maintaining the structure.
The firmware is installed only when the battery is fully charged and the power supply is connected.
Insert the memory card into your device in the off state.
Turn on the machine.
Select with the help of the volume rocker the option "Update".
Confirm with the power button.
At the end of the process, the program will ask you to remove the memory coil and automatically restart the device in a few seconds.
For Hard-Reset \ Wipe, use the "ClearUserData" option.

Please, if possible, reload this archive to other more convenient file exchangers.

Post has been editedmr.bin - 20.11.16, 13:58

[NormanV]

Began to show the battery charge 50%. When you connect the charger, it says that it is charging 50%. This figure does not increase, no matter how much it charges. Hard rezet not helped. Reset to factory settings too. The above firmware above firmware is not loaded. Does anyone have any thoughts (except how to carry in the service)?

[mr.bin]

NormanV @ 06/19/2013, 10:09 PM

Began to show the battery charge 50%. When you connect the charger, it says that it is charging 50%. This figure does not increase, no matter how much it charges. Hard rezet not helped. Reset to factory settings too. The above firmware above firmware is not loaded. Does anyone have any thoughts (except how to carry in the service)?

The firmware is installed only when the battery is fully charged and the power supply is connected.
If there is no charge, then the service is unique.

[mr.bin]

For those who like to experiment with their tablet-rut for ME172V
Me172vRootUtil_v0.1.zip(24.72 MB)

CWM 6.0 recovery for ASUS ME172v (memopad)
http://d-h.st/vgk
Details on the root and recovery read here
http://forum.xda-developers.com/showthread.php?t=2216390

Remember that all experiments with the tablet are entirely on your conscience.

Post has been editedmr.bin - 20.06.13, 09:18

[Arat_kiev]

mr.binTell me, please, what is the advantage of the firmware that you posted? If you can read more about her?

[mr.bin]

Arat_Kiev @ 06/21/2013, 09:24

Mr.bin, Tell me, please, what is the advantage of the firmware that you posted? If you can read more about her?

This is the original firmware from the manufacturer 4.5.4-16599690-20130326
Basically, it is necessary to restore the device to the "factory" state after experiments with the firmware, or if you suspect that the original firmware is damaged.
There are no custom assemblies yet, but the work is in progress ...
Read all the details here.
http://forum.xda-developers.com/showthread.php?t=2216390

Post has been editedmr.bin - 22.06.13, 16:09

[erbolat84]

16gb received root access. Did the ace according to the instructions: thank_you:

[promeo123]

Question - after installing Root and CWM is the warranty lost? And is it possible to return to its original state?

[mr.bin]

[email protected], 12:38

Question - after installing Root and CWM is the warranty lost?

of course

[email protected], 12:38

And is it possible to return to its original state?

In theory, yes, flashing stock firmware.
However, I did not check, risky.
From the "bugs" declared on xda-developers, this is alarming: Doing adb reboot bootloader or adb reboot fastboot bricks the device.
On the other hand, it is unlikely that it will be possible to establish the cause of the dying tablet on the briquette warranty device)
So you need a daredevil for tests, which can be repaired under the guarantee of a dead man)))

[afonyasafin]

Hooray everything turned out.
Made a ROOT, put the PPP widget version 1.15. And it all worked, on the new version that he did not want to work in the market.
Thanks mr.bin: thank_you:

[promeo123]

[email protected], 13:06

Hooray everything turned out. Made ROOT

afonyasafinafter installing ROOT functionality has not changed? Maybe bugs appeared?

[afonyasafin]

No, it feels good.

Guys help !!!
The second such tablet began to be ruled, and after removing the memory card, it turned off as it should be and now it does not turn on.
What are some suggestions other than throwing away?

Rebay translate as a root to install the translator nk helped: beee :: fool:

Post has been edited- SVD - - 09.02.14, 00:44

[IgorVS]

Glebkrytoi @ 06/28/2013, 15:03

Rebay translate as root, set translator nk helped

I join the request !!! By step if possible, for teapots, how to make root. : yes2:

[Leon-Leopard]

I watch everything here they beg for instructions on how to install the root, I will say right away that the operation is not complicated, but for some reason it causes problems for everyone, and so it is a landmark:
1) Cooking a flash drive byof this instructionwe need steps 1, 2 and 4 ...
Training:download the program, set, stick a flash drive, run ... (I can say one thing about the flash drive, I did it for 2GB, with the second attempt it turned out, I did not understand the instructions whether it will work with large volumes or not, but most likely it will, because I I do not see...)
Step 1: Remove the partition from the flash drive. Attention! You will lose all data from a flash drive! (right click on the flash drive ->Delete)
Step 2: Create a FAT32 / Primary partition (right click on a flash drive ->Create As, in the opened window set File System: FAT32 and Create As: Primary, press OK)
Step 4: Save all changes (click on the Apply button, on the top left, a green check mark, the program will create a partition and will format the USB flash drive)
All flash drive is ready, go ahead:
2) Open the archivehttp: //savagemessiahzine.com/forum/dl/post/3104733/Me172vRootUtil_v0.1.zip
Copy the contents of the archive to a USB flash drive, the file (scriptcmd) and two folders (bspinst and me172v) should be in the root
Now the flash drive is ready, remove it from the PC
3) Turn off the tablet, insert a USB flash drive into it, hold down the volume rocker (I pressed the one closest to the power button) and turn on the tablet
4) If everything is done correctly in the preceding paragraphs, the tablet will start to boot from the USB flash drive, this will immediately become noticeable in the boot image, wait for it to boot into the blue screen with the following contents:

me172v Root Util 0.1 by f-que
select mode to continue ...
please read included readme.txt !!!

[] "root me172v"

[*] "shutdown"

[] "unroot me172v"

"Press [power button] to Confirm or [Volume up or down] to Select"

Use the volume rocker to select the item “root me172v” (or “unroot me172v” to restore the original state), activate it with the power button, wait until it requests to remove the USB flash drive (Please remote installation media!), immediately after removing the flash drive the tablet will begin to reverse countdown and reboot.
The successful completion of the operation will read the changed logo.

ATTENTION! To roll back to the previous state, you need files from this flash drive, because the program backs up the system files to it (they are in the me172v \ dump folder), therefore I recommend either to save the flash drive in this state, or to save all files from it (well, archive there, etc., so as not to lose ... )
I hope I talked in some detail about this procedure, and of course, this is only an instruction, all responsibility for the "curved hands" and the dead tablets rests solely on the performer, but not on the author of these lines ...

Post has been editedLeon-Leopard - 29.06.13, 19:27

[alviora]

Someone "ripped off" restored already? There is a patient writing, insert the cable and then says ready to boot, the computer installs adb firewood, but adb devices and fastboot devices do not issue anything.
How to dump into place? from the memory card does not start.

Post has been edited- SVD - - 08.02.14, 18:52

[Leon-Leopard]

Alviora @ 06/29/2013, 21:34

adb devices and fastboot devices

Hi, are adb and fastboot configured correctly? it seems they have shoals with adjustment, try again; Is the device in the system determined? what driver is worth?

Post has been editedLeon-Leopard - 30.06.13, 08:47

[alviora]

Leon-Leopard
Yes, it seems everything is fine, the driver just in case demolished and installed from the site of the asus. Adb also downloaded adt-bundle-windows-x86-20130522.
Okay, right now, I'll take another computer.

Post has been edited- SVD - - 08.02.14, 18:53

[promeo123]

Successfully made a root on thisof this instructionbut with a few digressions:
1. I did not format the memory card, leave it with all the data, the main thing is that the section beFat32andPrimary (not logical)
2. I did not press the volume button, I just clicked on the switch after I uploaded files from the archive to the memory cardMe172vRootUtil_v0.1.zip
3. Then you need to move the file to the memory card.scriptcmdto any folder, otherwise the tablet will be loaded into the mode upon reboot.Root util by f-que
P.S.) The procedure is very simple and there is a possibility of rollback.