TP-LINK TL-MR3220 - Discussion | [wifirouter] Discussion, firmware, problem solving
Larin @ 21.05.2015, 14:07
The OpenWRT failed to configure WiFi /
To flash the router original way after OpenWRT can use tftp or MTD method, but in no case do not sew through the Web-based interface. Otherwise you run the risk of "brick" instead of a router.The name of the firmware should not contain the word "boot"
Routers second revision V2.X being stitched one of the latter, restoring the factory firmware support means tftp-server.
v111v111 @ 21.05.2015, 15:47
To flash the router original way after OpenWRT can use tftp or MTD method, but in no case do not sew through the Web-based interface. Otherwise you run the risk of "brick" instead of a router. Firmware the name must NOT contain the word "boot"
Routers second revision V2.X being stitched one of the latter, restoring the factory firmware support means tftp-server.
Routers second revision V2.X being stitched one of the latter, restoring the factory firmware support means tftp-server.
I use a computer at the level of turn \ disable reflash the standard method. It can be detailed instructions.
Rollback with OpenWRT to the original TP-LINK TL-MR3220 firmware
You can flash the router in original way after OpenWRT using the tftp or MTD method, but in no caseDO NOT PASS through the Web-interface . Otherwise, you risk getting a "brick" instead of a router. The name of the firmware should not contain the word "boot"
Routers of the second revision V2.X being flashed by one of the latest, factory firmware support recovery via a tftp server. Therefore, before flashing alternative firmware, always update your native one to the latest version. If it was not possible to flash through tftp, then there should be no problems with MTD.
Firmware with TFTPD32
Download utility Tftpd32 HERE
Looking for firmware for your hardware revision intended for recovery. Such firmware does not contain the word boot in the title. Change the name of the firmware file: "mr3220v2_tp_recovery.bin or mr3420v2_tp_recovery.bin", respectively.
Connect the router to the computer using a network cable and change the IP address of the network card to 192.168.0.66, mask 255.255.255.0.
Disable antivirus and other firewalls present in the system.
Throw the image in the folder with the program TFTPD. Run it as administrator. When you click the Show Dir button, the file with your firmware should be listed. No need to configure anything.
Holding the WPS / Reset button, turn on the router, after loading the image, release the button and wait for the reboot.
After that, do not forget to return the receipt of the IP address automatically.
Looking for firmware for your hardware revision intended for recovery. Such firmware does not contain the word boot in the title. Change the name of the firmware file: "mr3220v2_tp_recovery.bin or mr3420v2_tp_recovery.bin", respectively.
Connect the router to the computer using a network cable and change the IP address of the network card to 192.168.0.66, mask 255.255.255.0.
Disable antivirus and other firewalls present in the system.
Throw the image in the folder with the program TFTPD. Run it as administrator. When you click the Show Dir button, the file with your firmware should be listed. No need to configure anything.
Holding the WPS / Reset button, turn on the router, after loading the image, release the button and wait for the reboot.
After that, do not forget to return the receipt of the IP address automatically.
MTD Firmware
Download programs PuTTY and WinSCP
Open WinSCP, select SCP protocol, address 192.168.1.1, port 22, User name: root, Password that was set earlier, click “Login”.
We answer all vague questions and see a window with files on your computer and on the router. Next, take the native firmware, rename it to code.bin and throw it on the router in the / tmp folder. Close the program.
Open PuTTY, select the SSH protocol, address [email protected] port 22, click "Connection". We type the password that was set earlier for root. We enter the router and type the command for its firmware:
You can do everything in one PuTTY by running the following commands:
Open WinSCP, select SCP protocol, address 192.168.1.1, port 22, User name: root, Password that was set earlier, click “Login”.
We answer all vague questions and see a window with files on your computer and on the router. Next, take the native firmware, rename it to code.bin and throw it on the router in the / tmp folder. Close the program.
Open PuTTY, select the SSH protocol, address [email protected] port 22, click "Connection". We type the password that was set earlier for root. We enter the router and type the command for its firmware:
mtd -e firmware -r write /tmp/code.bin firmware
You can do everything in one PuTTY by running the following commands:
cd / tmp
wget http://www.example.org/code.bin
mtd -e firmware -r write /tmp/code.bin firmware
wget http://www.example.org/code.bin
mtd -e firmware -r write /tmp/code.bin firmware
P.S. Attention: if you see the error "Writing from /tmp/code.bin to firmware ... [e] Failed to erase block" after flashing with the mtd method, do not turn off or restart the router, otherwise you risk getting a "brick". Probably, you used a version with a "boot" for flashing, for example, mr3420v2_en_3_13_27_up_boot (121206) .bin, try flashing with another version.
P.S. If you did not find the firmware without "BOOT", then before executing mtd -e firmware -r write /tmp/code.bin firmware you need to run the command
dd if = code.bin of = tplink.bin skip = 257 bs = 512
mtd -e firmware -r write /tmp/tplink.bin firmware
Post has been editedv111v111 - 01.06.15, 13:53
v111v111 @ 21.05.2015, 20:19
Rollback with OpenWRT to the original TP-LINK TL-MR3220 firmware
Thanks to him. Won. I will now try to channel to try to finish the normal speed of traffic and trimming 4g modem
Guys, help me understand. the Russian-speakinghttp: //www.tp-linkru.c...R3220&version=V2#tbl_jthe latest version of TL-MR3220_V2_131217_RU on 12/17/2013. on the Englishhttp: //www.tp-link.com...R3220_V2.html#Firmwarethe latest version of TL-MR3220_V2_140929 on 09/29/2014. Why is it, what is the difference and what to take? The goal: to have the MTS modem (modelku not tell you, now is not on hand) for stable operation mainly in the 4G network. At the moment, with any of the firmware connects a very long time (about two minutes), and at the first opportunity falls in the 3G network, which directly affects the speed. Teach you be so kind as well pokoldovat over the modem / router to achieve stability.
koimi @ 22.05.2015, 09:43
Why is it, what is the difference and what to take?
take with the English language. if destined Handling the modem, it will be not worked. a newer version is always better.
Post has been editedrampa80 - 22.05.15, 08:51
A treat auto-switching to 3G in what way?
Upd: Clarified whistle Model - MTS 827F. Is there a quick way to throw him some command to transfer to the "4G only" mode?
Post has been editedkoimi - 22.05.15, 11:32
Upd: Clarified whistle Model - MTS 827F. Is there a quick way to throw him some command to transfer to the "4G only" mode?
Post has been editedkoimi - 22.05.15, 11:32
koimi @ 22.05.2015, 08:05
MTS 827F. Is there a quick way to throw him some command to transfer to the "4G only" mode?
AT ^ SETPORT? - Displays the current port configuration
AT ^ SYSCFGEX = "00", 3fffffff, 2,4,7fffffffffffffff , - Automatic.
AT ^ SYSCFGEX = "02", 3fffffff, 2,4,7fffffffffffffff , - Only 3G.
AT ^ SYSCFGEX = "02", 400000,2,4,7FFFFFFFFFFFFFFF , - 3G (2100 MHz)
AT ^ SYSCFGEX = "02", 400000,2,4,40,
AT ^ SYSCFGEX = "02", 2000000000000,2,4,7FFFFFFFFFFFFFFF , - 3G (900 MHz)
AT ^ SYSCFGEX = "02", 2000000000000,2,4,40,
AT ^ SYSCFGEX = "02", 2000000400000,2,4,40, - 3G (900/2100 MHz)
AT ^ SYSCFGEX = "03", 3fffffff, 2,4,7fffffffffffffff , - Only 4G.
AT ^ SYSCFGEX = "0302", 3FFFFFFF, 1,2,7FFFFFFFFFFFFFFF , - 4G / 3G.
AT ^ SYSCFGEX = "00", 3fffffff, 2,4,7fffffffffffffff , - Automatic.
AT ^ SYSCFGEX = "02", 3fffffff, 2,4,7fffffffffffffff , - Only 3G.
AT ^ SYSCFGEX = "02", 400000,2,4,7FFFFFFFFFFFFFFF , - 3G (2100 MHz)
AT ^ SYSCFGEX = "02", 400000,2,4,40,
AT ^ SYSCFGEX = "02", 2000000000000,2,4,7FFFFFFFFFFFFFFF , - 3G (900 MHz)
AT ^ SYSCFGEX = "02", 2000000000000,2,4,40,
AT ^ SYSCFGEX = "02", 2000000400000,2,4,40, - 3G (900/2100 MHz)
AT ^ SYSCFGEX = "03", 3fffffff, 2,4,7fffffffffffffff , - Only 4G.
AT ^ SYSCFGEX = "0302", 3FFFFFFF, 1,2,7FFFFFFFFFFFFFFF , - 4G / 3G.
It seems to be like that.
People! Someone recently tried to collect firmware OPENWRT using OpenWrt-ImageBuilder? And then I'm going chaos_calmer or trunk, and leaves only the v1 and I need to v2. And I try to do so with the same sortsy, obtained in the same! Did on Ubuntu86 / 64, xUbuntu86 / 64 the result is! Although if a file: \ target \ linux \ ar71xx \ image \ Makefile to change the parameter DEVICE_PROFILE: = TLMR3220V2 on DEVICE_PROFILE: = TLMR3220 is created v2. Although the flood had not yet tried.
Post has been editedWosh - 22.05.15, 19:49
Post has been editedWosh - 22.05.15, 19:49
2-v2. In general, all assembled, it works! just need to change the setting DEVICE_PROFILE: = TLMR3220V2 on DEVICE_PROFILE: = TLMR3220. See where it developed forgot to add!
P.S.
Post has been editedWosh - 22.05.15, 23:06
P.S.
Just wanted to add support for new core camera and Russian interface. If you download the finished version of the trunk, it is without a web interface! And there is enough memory or on it or on the camera support. Now I've got the camera is connected directly to the USB, and there is a Russian interface.
Post has been editedWosh - 22.05.15, 23:06
v111v111 @ 23.05.2015, 07:42
So b shared with the people
Not sure it's good! There is no support for USB modems, PPP connections and added drivers for my Chinese chamber. And why is it you? Although I can gather under which any needs. Or clean trunk. although there is also no support for modems by default.
v111v111, Download herehttp: //downloads.openw.../14.07/ar71xx/generic/since the web professionally assembled pure kernel packages are installed modem, and language packs, and then in the end you have 51% free space for the installation of packages, and a half-empty RAM, customized systems Volume of much less than even multi Web Lite, ie trimmed, nice work
These packages, in the following order
chat
comgt
kmod-usb-serial
kmod-usb-serial-wwan
luci-proto-3g_0.11.1-1_ar71xx.ipk
kmod-usb-serial-option
luci-i18n-russian_0.12 + svn-r10530-1_ar71xx.ipk
you take the same place where the firmware section packs, language packs in luki section mouth opkg install command example opkg install chat_2.4.7-2_ar71xx.ipk
opkg install luci-i18n-russian_0.12 + svn-r10530-1_ar71xx.ipk
Post has been editedvirtual13 - 23.05.15, 14:21
virtual13, Could offer even be newer:http://downloads.openwrt.org/chaos_calmer/15.05-rc1/ar71xx/generic/luci and there is built also
Wosh At the beginning of the year probyval chaos calmer but Luci has not been and can not fit ... Probyval compile but encountered an error and scored the ... Thanks for the link, conductive run updated!
Wosh do not say anything, really cool, just a little differently modem placed
Post has been editedvirtual13 - 24.05.15, 12:40
Wosh @ 23.05.2015, 18:57
Could offer even be newer:http: //downloads.openw...05-rc1/ar71xx/generic/luci and there is built also
Location infa about vstroennС–y Luci Today probyval pour on the TP-Link TL-WR841N Luci no ... Now just TP-LINK TL-MR3220 is not at hand to check that ...
Post has been editedv111v111 - 26.05.15, 22:22
v111v111, 1505 I tried to put on 3420v2 web is (maybe not on all models), the mass of the protocols, but after 3g mouth and the language pack remains about 110KB, of course not enough, for this reason, remained at 1407 tonnes to at the mouth of the East 347kb ie 51 % under the bags and less RAM is loaded well and need easy doustanovit packs are mostly compatible, except kmod-usb-serial and kmod-usb-serial-option, and that's all that while it was possible to try other routers on hand was not
Yes ... of Luci in the chaos calmer 15.05-rc1 has not for all models to see, specifically checked by installing a TL-WR841N V8 .... (4 mb flash) ... Luci no ...
Here is
But
Judging by the empty space must LUCI vlest ... Now just TP-LINK TL-MR3220 is not at hand that would check and hand reflash already scratched here and asked
Post has been editedv111v111 - 26.05.15, 22:24
Here is
List of installed packages
base-files - 157-r45745
busybox - 1.23.2-1
dnsmasq - 2.73rc8-1
dropbear - 2015.67-1
firewall - 2015-02-26
fstools - 2015-04-14-e6004000ff15d7bd32cf5663e8690fc94d7ec747
hostapd-common - 2015-03-25-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.17-1
iwinfo - 2015-03-23-40f2844fadc05f4a4de7699dbc12fee295b7057b
jshn - 2015-05-08-a8e70c6d361967a23977417fb7d6cf56234f8b81
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.18.14-1-ce6f0495ef84ff11b7151c697fe3240a
kmod-ath - 3.18.14 + 2015-03-09-3
kmod-ath9k - 3.18.14 + 2015-03-09-3
kmod-ath9k-common - 3.18.14 + 2015-03-09-3
kmod-cfg80211 - 3.18.14 + 2015-03-09-3
kmod-crypto-aes - 3.18.14-1
kmod-crypto-arc4 - 3.18.14-1
kmod-crypto-core - 3.18.14-1
kmod-gpio-button-hotplug - 3.18.14-1
kmod-ip6tables - 3.18.14-1
kmod-ipt-conntrack - 3.18.14-1
kmod-ipt-core - 3.18.14-1
kmod-ipt-nat - 3.18.14-1
kmod-ipv6 - 3.18.14-1
kmod-ledtrig-usbdev - 3.18.14-1
kmod-lib-crc-ccitt - 3.18.14-1
kmod-mac80211 - 3.18.14 + 2015-03-09-3
kmod-nf-conntrack - 3.18.14-1
kmod-nf-conntrack6 - 3.18.14-1
kmod-nf-ipt - 3.18.14-1
kmod-nf-ipt6 - 3.18.14-1
kmod-nf-nat - 3.18.14-1
kmod-nf-nathelper - 3.18.14-1
busybox - 1.23.2-1
dnsmasq - 2.73rc8-1
dropbear - 2015.67-1
firewall - 2015-02-26
fstools - 2015-04-14-e6004000ff15d7bd32cf5663e8690fc94d7ec747
hostapd-common - 2015-03-25-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.17-1
iwinfo - 2015-03-23-40f2844fadc05f4a4de7699dbc12fee295b7057b
jshn - 2015-05-08-a8e70c6d361967a23977417fb7d6cf56234f8b81
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.18.14-1-ce6f0495ef84ff11b7151c697fe3240a
kmod-ath - 3.18.14 + 2015-03-09-3
kmod-ath9k - 3.18.14 + 2015-03-09-3
kmod-ath9k-common - 3.18.14 + 2015-03-09-3
kmod-cfg80211 - 3.18.14 + 2015-03-09-3
kmod-crypto-aes - 3.18.14-1
kmod-crypto-arc4 - 3.18.14-1
kmod-crypto-core - 3.18.14-1
kmod-gpio-button-hotplug - 3.18.14-1
kmod-ip6tables - 3.18.14-1
kmod-ipt-conntrack - 3.18.14-1
kmod-ipt-core - 3.18.14-1
kmod-ipt-nat - 3.18.14-1
kmod-ipv6 - 3.18.14-1
kmod-ledtrig-usbdev - 3.18.14-1
kmod-lib-crc-ccitt - 3.18.14-1
kmod-mac80211 - 3.18.14 + 2015-03-09-3
kmod-nf-conntrack - 3.18.14-1
kmod-nf-conntrack6 - 3.18.14-1
kmod-nf-ipt - 3.18.14-1
kmod-nf-ipt6 - 3.18.14-1
kmod-nf-nat - 3.18.14-1
kmod-nf-nathelper - 3.18.14-1
But
FREE PLACE
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 768 224 544 29% /
/ Dev / root 2048 2048 0 100% / rom
tmpfs 14260 76 14184 1% / tmp
/ Dev / mtdblock3 768 224 544 29% / overlay
overlayfs: / overlay 768 224 544 29% /
tmpfs 512 0 512 0% / dev
rootfs 768 224 544 29% /
/ Dev / root 2048 2048 0 100% / rom
tmpfs 14260 76 14184 1% / tmp
/ Dev / mtdblock3 768 224 544 29% / overlay
overlayfs: / overlay 768 224 544 29% /
tmpfs 512 0 512 0% / dev
Judging by the empty space must LUCI vlest ... Now just TP-LINK TL-MR3220 is not at hand that would check and hand reflash already scratched here and asked
Post has been editedv111v111 - 26.05.15, 22:24
©savagemessiahzine.com2005-2020 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement