Assistant
REPLY |
RAM (RAM) | choice, discussion, problem solving |
Message#2 28.01.14, 01:08 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | People, help me figure it out so that I don’t have much interest in such matters. The computer is assembled on the motherboard GA-EP45C-DS3 (rev. 1.0) Previously, there was a DDR-3 operative with 2 strips of 2 GB each (1600) and everything worked fine. Operative (for certain circumstances) had to sell. I bought a replacement for DDR-3 1 bar for 4GB (1333) and the computer simply does not turn on, the screen is black, the computer restarts indefinitely, all indicator lights (in the upper right corner) are lit ... The question arises: maybe these slots for ddr-3 do not support 4GB, or it may fundamentally need to occupy 2 slots at once (such as dual-channel mode), can this mode be disabled in the BIOS or somehow get the computer loaded with 1 bar in 4 GB? ? Good advice is needed |
Message#3 28.01.14, 01:17 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | found the following line on the official site: 2 x 1.5V DDR3 DIMM sockets supporting up to 4 GB of system memory (2 x 1.5V DDR3 DIMM sockets supporting up to 4 GB of memory) Only now it is not clear 1 slot should be up to 4 GB or up to 4 GB in total. And yet is it possible to bypass this rule as a thread? |
Message#4 28.01.14, 10:53 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 272 Check in: 10.01.10 Xiaomi Redmi 4X 3/32 Reputation: 10 | found the following line on the official site: 2 x 1.5V DDR3 DIMM sockets supporting up to 4 GB of system memory (2 x 1.5V DDR3 DIMM sockets supporting up to 4 GB of memory) Only now it is not clear 1 slot should be up to 4 GB or up to 4 GB in total. And yet is it possible to bypass this rule as a thread? Each slot up to 4Gb. Is there a manual from the mother? It is necessary to read about the memory modes. |
Message#5 28.01.14, 11:02 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 272 Check in: 10.01.10 Xiaomi Redmi 4X 3/32 Reputation: 10 | Each slot up to 4Gb. Is there a manual from the mother? It is necessary to read about the memory modes. Judging by the photo of the board from Ineta, you have 6 connectors for it on RAM. Of these, 4 under ddr2 and 2 under ddr3. A natural question arises: did you put your memory bar in that connector? |
Message#6 28.01.14, 12:50 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | There is another connector under ddr2, ddr3 there is no problem =) So why then does not see the bar in 4 GB if one slot to 4 = ( The manual is there but everything in English devil's leg will break |
Message#7 28.01.14, 16:21 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 272 Check in: 10.01.10 Xiaomi Redmi 4X 3/32 Reputation: 10 | |
Message#8 29.01.14, 13:10 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | No, constant reboot + black screen, everything is as if the operatives in the slot are not at all |
Message#9 29.01.14, 13:58 | |
EvilGenius [offline] Group: Friendssavagemessiahzine.com Messages 608 Check in: 23.07.09 Nokia Lumia 1520 Reputation: 31 | Do you have a mother? If it was 1600, then it is necessary to chemize it with voltage. I found your mother, a hybrid of GA-EP45C-DS3, it seems to me that it is unlikely that 1333 will rise, remove the RAM and change it to 1600 is not easy because the mother has such characteristics. Post has been editedEG.Gnom - 29.01.14, 14:06 -------------------- |
Message#10 29.01.14, 18:12 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | 1600 is the limiting frequency, I used to have 2GB of 1333 and all the rules worked, then there were 2x2GB of 1600. But 1 slat for 4GB neither to the village nor to the city, it looks like it simply does not support 4 GB in one slot = ( |
Message#11 29.01.14, 18:13 | |
Local [offline] Group: Friendssavagemessiahzine.com Messages 272 Check in: 10.01.10 Xiaomi Redmi 4X 3/32 Reputation: 10 | EG.Gnom, The characteristics of the 1333 board are supported ... but in general, it would be nice to try other strips. |
Message#12 29.01.14, 18:50 | |
EvilGenius [offline] Group: Friendssavagemessiahzine.com Messages 608 Check in: 23.07.09 Nokia Lumia 1520 Reputation: 31 | |
Message#13 29.01.14, 20:56 | |
VZHYK! [offline] Group: Friendssavagemessiahzine.com Messages 9277 Check in: 31.07.07 Fujitsu-Siemens Loox C550 Reputation: 1945 | Only now it is not clear 1 slot should be up to 4 GB or up to 4 GB in total. Most likely, the second. OnlineTranscendthere is a "compatibility check". For GA-EP45C-DS3, the following is written: Maximum Memory: 4 GB using DDR3, 16 GB using DDR2 And on gigabyte's websiteQVLfor ddr3 - only 2GB slats. -------------------- Posted in HP without asking - was blacklisted. xxx: a Google abolished or religion does not allow? yyy: Google is the Matrix, the less you ask it, the weaker the machines will be during the Great Battle |
Message#14 30.01.14, 20:29 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 79 Check in: 08.07.11 Reputation: 0 | The problem with RAM, thanks in advance Mother asus p8h77, i5 3470 percent like, and there were 2 1333GHz 8 and 2GB slats in the neighboring slots (I know what a fool, but more on that later). I decided to put extra. cooler - it is said done, but the computer problem turns on and after 3-5 seconds it is cut down, the monitor-keyboard-mouse does not work, they do not even blink when turned on In the past, this happened, he treated by resetting the bios, this time it did not help, after repeated disassembling and assembling and dancing with a tambourine, it worked. Well, well, I collected the computer, sat for a couple of hours, turned it off and went to bed. Today everything is repeated and nothing helps, I noticed that the DRAMLED indicator on the motherboard is lit in red, which means the memory is not installed or there is some kind of malfunction, it started up without the slats themselves - everything is the same, it means the mother or BIOS simply cannot see Memory is working - I checked the system unit for others, change slots, put on 1 and 2 also tried Sometimes the problem changes, the computer turns on but nothing works (monitor, etc.) And there are also Kingston kvr16n11 / 8 and Hynix 2GB 1Rx8 PC3 slats - 10600U - 9 - 11 - A1 I really hope for your help, I just need a computer. |
Message#15 30.01.14, 23:48 | |
EvilGenius [offline] Group: Friendssavagemessiahzine.com Messages 608 Check in: 23.07.09 Nokia Lumia 1520 Reputation: 31 | I do not understand you 2 strips 1 and 2GB? Leave the one for 2GB. Maybe Kingston does not want to work with Hugh Nyx, wipe the contact pad with an eraser, blow dust from the sockets, for the future different manufacturers of RAM cards are not critical, but they may conflict. Post has been editedEG.Gnom - 30.01.14, 23:49 -------------------- |
Message#16 31.01.14, 00:01 | |
User [offline] Group: Friendssavagemessiahzine.com Messages 79 Check in: 08.07.11 Reputation: 0 | EG.Gnom, I have 2 strips of 2GB and 8GB, somehow I returned everything to my places, left 8GB for Kingston, it seems to work, although yesterday it worked too But such a question, I have a Kinston 1600GHz, and Hünix 1333, maybe because of this conflict, and in general it is possible to put different-frequency strips with a different volume of memory in a couple? |
Message#17 01.02.14, 10:52 | |
EvilGenius [offline] Group: Friendssavagemessiahzine.com Messages 608 Check in: 23.07.09 Nokia Lumia 1520 Reputation: 31 | |
Message#18 01.02.14, 12:19 | |
a guest [offline] Group: Users Messages 5 Check in: 01.02.14 Apple iPhone 4S Reputation: 0 | OlegLUI, Little information, does the computer squeak when turned on? with RAM? Without her? What is worth besides the motherboard? What is the power of the PSU? Please add information and we will decide there. |
Message#19 04.02.14, 14:28 | |
Visitor [offline] Group: Active users Messages 18 Check in: 14.05.13 Huawei U8815 Ascend G300 Reputation: 0 | Thank you all, in general, I did not put 4 in one slot, but 2 by 2, because the wash is written there on the site that you can put up to 4GB in the slot. in general, everything works |
Message#20 29.05.14, 16:48 | |
Visitor [offline] Group: Active users Messages 18 Check in: 05.05.14 Reputation: 0 | Guys, the problem is this, on the GIGABYTE GA-M61VME-S2 motherboard there were two strips of 512 MB each, which are 640 MHz. I decided to expand and put one on 2 gig, and the other (512 MB) remained. The computer started up with two bars, but it stops at the line “WINDOWS START” and I don’t know what to do, help ... |
Message#21 18.09.14, 10:12 | |
Visitor [offline] Group: Users Messages 10 Check in: 30.08.14 Reputation: 0 | All good. I want to add a couple of strips of RAM Goodram DDR3-1333 4096MB PC3-1060 is now worth two bars. I need to purchase the same RAM, and also 4 GB each? Or can I insert 2 strips of 2 GB each? Do I need to look when choosing only the timings? or what else? where you heard a glimpse of 4 channel mode, is there something like that? If in two slots of 4 GB of memory, and in the other 2 slots, put on 2 GB. memory, 4 channel mode will not work? or 4 channel mode-myth? : helpsmilie: buy 2 more strips of 4 GB each. expensive at this time, but 2 to 2 GB. much cheaper. but if I need to pick up the same memory, then I will find her figs Post has been editedsolarpower - 18.09.14, 10:13 |
mobile version | Now: 05/05/19 17:11 |