TP-Link TL-WR841 - Discussion | [wifirouter] Discussion, firmware, problem solving
Good people, please help !!! WiFi periodically falls off periodically, for a few seconds (approximately 15-30 differently) and the wired Internet works without interruption !!! What could be the reason? In the settings I set both the avto and 13,12,6 channel, it still throws off periodically.
Post has been editedshturman-70 - 02.06.19, 01:04
Post has been editedshturman-70 - 02.06.19, 01:04
Reason for editing: ..
shturman-70 @ 06/02/19, 01:02
WiFi falls off periodically, for a few seconds
Read the logs of the router.
Herzz, Here I looked, but it's not a fig that is not clear !!!! Help if you know what this table means ???? |
Greetings forumites. I came here can say a problem. I have this tl-wr841n router (an internet cable is connected to it that goes from the entrance, the TTK provider) and xbox one, on the phone it shows that NAT is Moderate
And the fact that the 2 nd conversion of NAT was discovered, I climbed a little in the internet and saw that the N series of the router does not have NAT. And then I don’t know where to dig, I'm new to this.
Post has been editedMrForce23 - 02.06.19, 18:18
And the fact that the 2 nd conversion of NAT was discovered, I climbed a little in the internet and saw that the N series of the router does not have NAT. And then I don’t know where to dig, I'm new to this.
Post has been editedMrForce23 - 02.06.19, 18:18
shturman-70 @ 06/02/19 16:38
What means
What 100 101 and 103 IP router bans.
Most of all, the reason is Chinese devices.
Post has been editedHerzz - 02.06.19, 18:18
Such a problem. Router version 14. The incoming speed on the LAN cuts 1.5 times, outgoing 20 times. On the official firmware website it is newer than it costs from the factory no.
alexsv_01 @ 06/04/19 12:36
.Incoming speed over LAN cuts 1.5 times, outgoing 20 times
Provo call. Their cant.
Dir 100 does not cut it instead, and without a router directly the same everything is ok
Post has been editedalexsv_01 - 04.06.19, 15:44
Post has been editedalexsv_01 - 04.06.19, 15:44
alexsv_01, there is no Tplink tech support. And not the Consumer Protection Society.
Hands in legs - and carry where you bought it.
Thank you bro and I will do it. Helped in full. And what is the way here? Did you just read my original question?
Post has been editedalexsv_01 - 04.06.19, 16:56
Post has been editedalexsv_01 - 04.06.19, 16:56
alexsv_01 @ 06/04/19 12:36
The incoming speed on the LAN cuts 1.5 times, outgoing 20 times
1) Marriage. Bring where bought.
2) they threw him at the OLH - then try to save him.
If I connect the computer to the DIR 100 connected to the provider's Internet via the LAN WR841 and connect it to the LAN via the LAN, I run the speed test and get the same speed as the computer directly from the provider cable. Marriage router or jamb provider? Does the v14 version of the router have firmware other than the official one?
Post has been editedalexsv_01 - 05.06.19, 17:51
Post has been editedalexsv_01 - 05.06.19, 17:51
alexsv_01 @ 06/05/19, 19:04
Does the v14 version of the router have firmware other than the official one?
there is for example frompadavan
Good morning.
I have a TL-WR841N v9. Put versionChaos Calmer rc315.05
The purpose of the router is to connect in client mode via wifi and distribute Ineta through its wifi network when staying at hotels.
Faced the problem that after connecting to wifi networks, in which, in my opinion, additional actions are required to connect to the Internet, the router does not turn on its wifi network and I cannot connect to it. You have to do a full reset through the button.
In an attempt to solve this problem, I installed 18.06.2. in it, as I understand it, access to the wifi admin panel is disabled by default. Before returning home from a trip, the router lies like a brick. Tell me which firmware version to install or what settings to pre-register.
Post has been editedscooter4 - 08.06.19, 09:47
I have a TL-WR841N v9. Put versionChaos Calmer rc315.05
The purpose of the router is to connect in client mode via wifi and distribute Ineta through its wifi network when staying at hotels.
Faced the problem that after connecting to wifi networks, in which, in my opinion, additional actions are required to connect to the Internet, the router does not turn on its wifi network and I cannot connect to it. You have to do a full reset through the button.
In an attempt to solve this problem, I installed 18.06.2. in it, as I understand it, access to the wifi admin panel is disabled by default. Before returning home from a trip, the router lies like a brick. Tell me which firmware version to install or what settings to pre-register.
Post has been editedscooter4 - 08.06.19, 09:47
Yoparasete .. Well, is it normal when the speed is 80, and is there only 50 for a wifi? Now DD-WRT v3.0-r30949 std (12/15/16). maybe there is something better?
Post has been editedvasil7771 - 08.06.19, 10:58
Post has been editedvasil7771 - 08.06.19, 10:58
©savagemessiahzine.com2005-2019. All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement