Write, plz, manual how to put Reactos OS on the PDA !!! Plz !!! What and where to change to speed up the work of the OS?
Thanks in advance! And throw off all one archive that is necessary for this!

Can I start a photo reaktos on the device?

Greatevk
put less vga_refresh_interval.
I have 4000 worth yuzat a little more - 8000.

Not how I can not make the mouse work in ReactOS in your version of Bochs-2.3.5 for PDAs. :(

Could you tell me where to write this parameter?<vga_refresh_interval>?
When entering it into bochsrc.txt, the emulator refuses to start, cursing while still in the console.
If it is there, then please indicate the correctness of its writing.
And another question is there any difference where to install ReactOS on a PC or PDA, for the correct operation of the mouse?

in the config file.



what does he specifically report?
in general, it will say that the value is small, but it will start.


no difference.
make sure that ReactOS has a mouse on the screen (i.e., the device is recognized).
do not forget to press F12 to activate the mouse.

Post has been editedGreatevk - 25.01.08, 22:38

in short, everything seems to be set, set up, in the barrel itself I don’t know what to do. I click on the diskette, open the .img file there. I shake ok. And the floppy disk is crossed out again and nothing has been put there ...

How to understand<vga_refresh_interval>?

Greatevk

You have any questions:
There are two moments when the mouse is activated before the ReactOS is loaded, it does not boot, after the mouse does not work. (the device is listed in my hat)
)
Tell me what to do?

AndreySemenov ,
as I understood it meant "vga_update_interval" - update frequency.
it does not depend on this parameter whether the mouse will work or not.
In this thread, I laid out my image of ReactOS, there is a 100% working mouse.

And where can I see the programs for the reactants?

How does the axis work at all? Smart or just like different Windows under the dos poket?
How about running programs for this axis?
And finally, is the qvga screen working fine?
=)

Zlobo ,
Windows under the poke dosom just flies compared to the reactor under the barrel. for reaktos prog as such, no, the purpose of the author to make the axis an analogue of Windows, to allow the program to run from Windows. from 10 prog, normally working on xp, only 2 were not started.

are you talking about?
links pliz.

I apologize for not being accurately expressed. I meant Vindovs 3.11, which quickly works under the poker dos.

here you go...
will have to try to run in Bochs.

What is the size of memory to specify to run the reaction?
I put 32 + turn on Rowout + divtwo, and also swap to the root - is the campaign the most optimal configuration ???
Share your experience ..

G.r.e.sh.n.i.k ,
A half-axle will slow down very much. Try to put vga_update_interval around 15000-30000, the overall performance should increase slightly.

No one has tried to install ReactOS-0.3.4-REL on Bochs.
When I install everything, everything stops at the choice of language, turned on the mouse off, does not help, as if the clave is not defined at all.
Checked on BB (2.3.6) and on the communicator (2.3.5).

It was possible to put ReactOS-0.3.4-REL on Bochs 2.3.5. :)
Loads 15-20 minutes, just did not notice.
The mouse works fine.
Special braking is not noticed. :)

Special braking of the mouse or system? :)

Could you post the image of the installed system.

img-75169-C.rar(17 MB)


In the archive image and config.
F12 click after loading React :)