[X]Assistant

[D.S.Denton]

Digma D-Plane² 7 ’’ iDxD7 3G - Firmware
Digma D-Plane² 7 ’’ iDxD7 3G
Description | Discussion пїЅ | Firmware пїЅ

Important information!

• before attempting the firmwarecheck revisiondevices!
  
• do not experimentwith firmwares by schemes -4.0>4.2>4.0, 4.2>4.0>4.2!
  

A note for updating Android 4.0 firmware

• DIDD7GBK8X211306xxxxx
  
• DIDD7GWT8X211306xxxxx
  
• DIDD7GBK8X211305xxxxx
  
• DIDD7GWT8X211305xxxxx
  

if the serial number of your tablet corresponds to one of the series of numbers, you can useONLY update Android 4.2 !!!
Otherwise, the tablet may fail.

How to determine the revision DxD 7 3G:
rev.1 DIDD7GxxAX1112xxxxxx
rev.2a DIDD7GBK8X2112110001 ~ DIDD7GBK8X2112112060
DIDD7GWT8X2112110001 ~ DIDD7GWT8X2112111030
rev.2b DIDD7GxxAX2112xxxxxx
Note: rev.2a and rev.2b are different camera module, if the camera does not work with one firmware, use another.

Drivers and Utilities

Adb
driversfor A4.0 and A4.2

Firmware

Latest stable firmware from the official site digma.ru

FirmwareAndroid 4.0.4

All that is left on my topic laid onYa.Disk

The factory_update_param.aml file for those firmware in the archives with which it is missing:factory_update_param.rar(143 bytes)

Test firmware laid out and discussed on the developer forumhereanda continuation - Topics closed

The freshest build everhere (sourceforge).

FirmwareAndroid 4.2

Archivea4.2on ddixlab
More firmware on Mail.ruDigma D-Plane² 7 ’’ iDxD7 3G - Firmware (Post nik.reneyj # 72101662)
Firmware on Android 4.2 laid out and discussed on the developer forumhere. - Topic is closed

MemoAlex @ 09/10/2013, 23:07

I remind the update procedure:

• - Format the memory card and unpack the firmware to the root of the card, insert the card into the off tablet
  
• - Press and HOLD the Volume + and Power combination before starting the update procedure
  
• - At the end of the update, give the tablet a boot, and turn it off
  
• - Remove the memory card and press Volume + and Power to enter the system menu
  
• - Run Wipe Cache
  
• - Run Wipe Data
  
• - reboot
  
• - Let the tablet boot up, wait a minute, TURN OFF
  
• - Turn on the tablet.
  

Everything.
P.S. Insert SIM card intoOFFthe tablet.

AndreyRS

In order to display the section for developers, you need to go to "About the tablet" and click on the assembly number 7 times.

Instructions

Getting root

On all the latest firmware root already available. You only need to install the application: Superuser (Superuser).
for 4.0.xSuperuser-3.1.3.apk(1.4 MB)
for 4.2SuperSU.apk

If you have a "boxed" firmware, use the instructions here:
Digma IDxD7 - Discussion (Post # 15918165)

Root removal :
Digma D-PlaneІ 7 ’’ iDxD7 3G - Firmware (OS 4.0) (Post # 17819896)

Instructions on firmware (universal for all tablets of the D-Plane2 series)
Download: from office the site | orfrom the mirror| or from here Firmware_update_manual_Digma_D-Plane_iDxD.pdf (147.72 KB)

A way to flip the old version with "error 7" (in some cases):
Digma D-PlaneІ 7 ’’ iDxD7 3G - Firmware (OS 4.0) (Post # 17853763)

Battery calibration (it is necessary when the device is turned off when the charge is supposedly present or the charge indicator constantly “sticks” by 100%):
Digma D-PlaneІ 7 ’’ iDxD7 3G - Firmware (OS 4.0) (Post # 19483546)
Update boot / recovery using aml_autoscript :
aml_autoscriptmore

miscellanea

Patch to improve GPS performance (published on November 28, 2012, use only for firmware released before this date!)
Download: From the office. the siteor from here SpeedPatchForGPS.zip (147.75 KB)

Patch instructions

1. Download and save the archive in the root of the memory card without unpacking it
2. Insert the card into the tablet
3. In the “Programs” menu of the tablet, start the Upgrade application by selecting Local Upgrade. Then you need to select the SpeedPatchForGPS.zip file and run the update.
4. Wait until the update is completed and the tablet is restarted.

After the update, it is recommended to reset and reload the A-GPS data. The first launch of GPS ("cold start") usually lasts a relatively long time, up to 10 minutes.

How to independently replace boot-animation:
Digma IDxD7 - Discussion (Post # 16109826)


In firmwarexxxFlash Player is missing or not working.
0. Think three times, do you really need it? There is no official support from Adobe for this device. Since this device works fairly tightly with the system, potentially your tablet becomes less stable in operation, especially problems with browsers occur. Without a problem, the flash player only works on a very small number of tablets, such is the Adobe policy.
1. Uninstall all versions of Flash Player and Flash Player Installer (if you tried to install by yourself).
2. Reboot.
3. Install:FlashPlayer-10.2.apk(4.2 MB)
4. Check that the .apk package itself falls into the device’s memory (/data/app/com.adobe.flashplayer-1.apk). If it is not installed there, but on the sdcard, transfer it with standard android tools (Settings / Applications).
5. Reboot.

What can be done with preinstall.sh

• preinstall - forced launch of silent installation of applications from sd card from preinstall directory
  
• backup - copy the current installed applications to the sd card in the preinstall directory
  
• batcalib - reset of PMU AXP2 * counters and android battery statistics data
  
• clearcache - clear application cache
  
• check_media - check internal flash with error correction
  
• format_media - repartitioning and formatting internal flash
  
• erase_media - complete cleaning of the flash with padding with zeros and marking of BAD sectors in NTFL with subsequent formatting after downloading (it may take a long time, at least 5 minutes)
  

How to change mount points (internal memory / external sd card) for4.0
You just need to replace the file /etc/vold.fstab with the attached one:vold.fstab.rar(515 bytes)
(for the possibility of a reverse change, we do not forget to first save somewhere in a secluded place a copy of the original file)

Other

Additional Information

1. Never insert or pull out a SIM card on a powered-on or non-sleeping device. The result of a short circuit with this action with considerable probability may be the failure of the slot for the SIM card or the SIM itself.
   
2. In case of transition between different firmware branches (including factory ones), it is necessary to perform wipe of all partitions after firmware since changed flash layout. In fact, it is better to do a full wipe with any firmware, even when upgrading within one branch - this is additional insurance against unpredictable glitches on any device.
   
3. After flashing and initial setting, before starting regular use, be sure to shut down the device correctly and turn it on again.
   
4. In no case do not install busybox from the market - this will lead to the inoperability of part of the logic and unpredictable glitches. The firmware already has the latest version of busybox with amlogic-specific patches.
   
5. Do not enable 2D acceleration mode in the settings for developers, this option is only for debugging. The probability of glitches with the included - 146%.
   
6. All our firmware support the function preinstall (pre-install applications after firmware). To use it, you need to create a preinstall directory on the card with the firmware, where to put the software packages that will be automatically preinstalled after the firmware. This function is made in order not to litter the firmware with third-party applications and to allow users to independently create a software package for installation out of the box.
   Presetting is performed in silent mode while the user fills in the data for the accounts, etc. Preset may take a long time (depending on the set of applications). Progress is not indicated in any way, so after the firmware it is advisable to leave the device alone for 15 minutes until the pre-installation is complete, and then restart the device. If you remember the entire list of applications, you can simply check through the package manager (Settings ->Applications) are they all already established?
   
7. It is also possible to make a copy of the current installed applications in preinstall. To do this, from the root on adb or in the terminal, give the command preinstall.sh backup and wait for the end of copying applications to flash. Also preinstall.sh supports batcalib and cleancache commands. Appointment I think it is clear from the title. For more information about the features of preinstall.sh, see the "Other" spoiler.
   

Famoushardwareproblems not fixed by firmware

1) A non-working or incorrectly working simdetect - a marriage of the sim socket, is treated at a service center. A partial solution is to turn off the sim card presence check in the developer section.
2) Bad contact of the card in the sim connector (the verification method is absent, indirectly, the problem can be judged by the logs of the rila which is trying to read the sim card endlessly or starting from among the session it starts endless attempts to re-register on the network). Software solutions also do not carry in service.
3) Spontaneous triggering of the wheelbarrow when charging is connected (test method: turn on the display of the pointer location in the settings for the developer and hold the finger in one place while the charger is connected, while the pointer will randomly jump around the screen). The method of elimination is the replacement of a power supply unit with a stabilized power source. Better if it is a classic transformer power supply. Cheap impulse sources will not solve the problem.

One example to paragraphs 1 and 2:Digma D-PlaneІ 7 ’’ iDxD7 3G - Firmware (OS 4.0) (Post # 18435007)

For Qumo Galileo users - possible specific problems and their solutions.

Q1: It is impossible to flash any revision, after the firmware it hangs tightly on the start screen of Digma

Background and Decision

Gandalff @ 05/11/2013, 19:03

I have a Galileo, I want to flash in Digmu.
It does not work at all, all the time after the firmware the Digmy start screen is loaded and everything (the screen was touching, nothing happens). I put different versions of firmware, different revisions - the result is the same.
The firmware from the Kumo site is installed correctly, the tablet is working again.

MemoAlex @ 05/13/2013, 15:10

Most likely, you need to update the bootloader / recovery

Procedure:

1. First, make sure that the problem is not in the card: re-download the firmware, format the card and unpack the archive on it, for accuracy
   
2. Turn on the tablet, hold Volume + and Power for about 40 seconds (do not release the volume button until the update starts)
   
3. If there is still the same problem, download and unpack the file attached to the card.this postand try to flash already with him.
   

Survey Screenshots

Topics Curator - _sudo_

Post has been edited_sudo_ - 10.04.18, 20:14

Reason for editing: upd

[Conlar]

is there anyone here?

[iceforce]

Conlar @ 01/19/19, 11:37

on Digma Plane 7.5 3G fit? And yet, how to flash a computer? Or is it ONLY from a flash drive?

Will not work
Going around - no way
Only with a flash drive

[Conlar]

iceforce,that means, as I understand, only the "only off" and only from the flash drive .... sorry. but her weight is 2 times greater than that of these! is this normal? : rolleyes:

[iceforce]

Conlar @ 01.20.19, 12:05

but her weight is 2 times greater than that of these! Is this normal?

I think so, it happened more than once

[Conlar]

So how to flash it (I'm talking about digma plan 7.5 3ji) ??? what to choose in the menu? there has never been a problem if the map is asking for it, but here is some kind of trap! o.O what buttons to press? In the "on" on all points there is no command. on + the team is going, just did not understand what. infa, the one that found - not suitable! What is he, a secret? : blush:
P.S. Or does TWRP need to be delivered first?

Post has been editedConlar - 21.01.19, 10:06

[ALEX8]

Conlar look here.Firmware_update_manual_Digma_D-Plane_iDxD.pdf(167.96 KB)

[Conlar]

ALEX8,Looked - does not fit! In general, the instructions that I found ... as if not from my device! Recovering from a hang-up - put the battery to zero and charge again ... but with the old firmware: blush: how to flash a new one (although it is one of our bodies And I do not understand - maybe you should not flash it! The numbers are different) I did not understand
P.S. I have no D-PlaneВІ! but just Digma Plane 7.5 3G. they send here from that topic, and there is no such model here. I jump here and there and to other sources, in the hope that I will achieve something.
P.S.2 here is what the "unzipped archive" says "

Post has been editedConlar - 22.01.19, 17:48

[V990]

Hello, such a problem with the tablet: it loads normally, but when it goes into standby mode, when you press on, it shows a small screen on half the tablet. I want to try to upgrade, tell me what revision

Post has been editedV990 - 04.02.19, 21:34

Reason for editing: Photo