[X]Assistant

[repain]

Pantech Burst - Firmware (OS 2.3- 4.0)
p9070
Description | Discussion пїЅ | FirmwareпїЅ

Important information

[center] [color = royalblue] [b]Before asking anything, read the hat or
Use the search on the topic!Remember, everything that you do, you do at your own peril and risk, and the responsibility for your actions lies solely with you. All the described actions on firmware, Russification, rutting, etc. are purely exploratory in nature, and it’s up to you to take either action!

Drivers and Utilities

Pantech PC Suite(without it, the computer does not see the phone)
Sometimes you need to installPdaNet (PC)(not needed with the release of the new version of PC Suite (not verified))
P9070 Download Tool v3.3
Pantech_Burst_OsUpgradeTool_Ver2.7.0(official utility for upgrading from 2.3 to 4.0.4)

CWM FAQ

link

Official firmware

2.3

Link (sew through recovery)

Alternative firmware method (use if by some miracle you demolished the system and recovery)

ATTENTION with alternative firmware unlock flies! Before flashing, find out and save your unlock code
1. downloadPANTECH_PRESTO_BIN_JUUS03122012.pdl
2. downloadP9070_Download_Tool_v3.3.zip
3. turn on the body in Download mode (with the phone turned off, the volume is down, the volume is up, and the power button)
4. run P9070_Download.exe
5. select Open file and select .pdl file
6. select ”Reload File”
7. select "Download"
8. choose the location of the xml log file

Thanks for the translationFinn81

4.0

The official way to switch from 2.3 to 4.0.4 (recommended!)

Attention! After flashing 4.0 in this way, we get a closed bootloader. If you install custom firmware on a closed boot - get a brick !!
Also, after the firmware all your data will be deleted!
1. Download and unpack thisarchive
2. Run the exe file and follow the instructionson the official site, fortunately there is a step-by-step instruction with pictures.
3. At the 8th step of the instruction, you can close the program, and your phone should already be with 4.0.4.
Further, if desired, you can unlock the bootloader to install custom firmware, or get root and CWM, for this, read the spoiler "Instructions".

Unofficial way to switch from 2.3 to 4.0.4
juus09032012-deodex-cwm-6.0.2.7.zip

Custom firmware

MUIUv5

Assembled by electrod`om

CM10

The most extreme build can always be downloadedhere.

Topic on XDA

Because our forum member takes part in the development, leave all your "thanks" in his profileninja83

Screenshots

Does not work

1. Compass
2. Mounting cards to the computer (only works if you enable ADB and set root rights for adb and applications)

Gizmolord project 2013

topic on XDA
Google drive

List of changes

### CHANGELOG ###
- Removed all At & T crapware and some other apps also .34 Apps in total removed.
- Rooted.
- cwm-5.0.2.7. (it will replace the older / newer one)
- Bravia Engine.
- New default wallpaper.
-Whole New wallpaper Gallery.
-Cyanogen Browser.
-Added Appolo, AOSP phone, AOSP contacts, AOSP messaging, AOSP calendar and calculator.
- Jelly bean transitions.
-New icons.
- Added DSP Manager.
-Various build.prop tweaks.
-Aderline Engine.
-Few battery tweaks and performance tweaks.
-New boot animation.
- AOSP Desk clock.
-New sounds.
-Google now.
-Themed phone, systemui.apk, framework-res.apk, videoplayer.apk, pantech home.apk, phone.apk and settings.apk.
-Highly polished performance and battery.
-New fonts.
-4.2 Keyboard
-Zipalighned
-New icons
## Changelog V4.0 ##

-New sounds
--CWM Touch 6.x by attn1
-Updated theming
-Updated Superuser.apk
-Disabled journalism
-Ad blocking host
-AOSP lockscreen
-Fixed Google now with offline support also.
-Swap supported
-New boot animation
-Changed / Added a few new icons

Installation Instructions

Stock ROM mod
Stock ROM mod lite

Custom kernels

Electrod core for 4.0.4

Instructions

root + cwm + unlocked bootloader in one click

http://www.mediafire.com/download/85qm8fme...ch_Hack_Kit.exe
extract the contents of the archive
we connect the phone in debug mode by usb (previously, of course, drivers must be installed)
run the hack-burst batch file (the phone will reboot several times)
optionally offered to unlock the uploader (YES - agree or NO - refuse)

A simple way to get root and CWM for 2.3 and 4.0.4 (recommended!)

1. Make sure that your phone has stock 2.3 or 4.0.4
2. Make sure adb and fastboot work on your PC.
3. Download and unzip the archive for thisreference.
4. Run the bat file.
5. Wait for the phone to reboot into CWM.
6. Click "install zip from sdcard"
7. Click "choose zip from sdcard"
8. Find and install "p9070.cwm.rooter.marduk191.zip"
9. Reboot the phone (tap on "Reboot system now").
Now you have the root / CWM / Full Fastboot / busybox / init.d.
Log in to recovery - when the phone is turned off, the volume is down + the power button.

If you suddenly have any problems and you cannot connect to fastboot ...

... then you probably have to manually install the drivers.
download here
1. Extract "p9070.Pantech.Burst.Driver.marduk191.rar" to the root of your C: to avoid further problems (C: \ p9070.Pantech.Burst.Driver.marduk191)
2. Go to the Device Manager and right-click on "Android", it is marked with a yellow exclamation mark, and click on "Update Drivers"
3. In the next window, select the second checkbox "Search for drivers on this computer"
4. In the next window, select the second option again with the inscription "Select from the list of device drivers on my computer"
5. In the next window, select "Show all devices" and click Next.
6. In the next window, click on the "Install from disk" button
7. In the following dialog box, copy and paste this text (without quotation marks): "C: \ p9070.Pantech.Burst.Driver.marduk191"
8. Click on the OK button and select "Android Bootloader Interface" and click Next
9. Click on the “Yes” button on the warning, and again try to get root and CWM.

The author of the method marduk191

If suddenly the previous method did not help you:

Route and CWM for 2.3

1. Download and unziparchive(in this archive the necessary "piece" of JDK and SDK is collected in one place so as not to download and install a bunch of unnecessary garbage + directly images to get root and recovery)
2. Turn on the debug mode on the phone (Settings>Applications>Development>USB Debugging)
3. In my case, I needed to start on the computer and search for the device through the installed Pantech PC Suite
4. Open the console window in the folder (hold Shift, right-click on the folder, then click "Open command window"), where they unpacked burst_root_cwm.7z
5. Run from the console "adb reboot bootloader"
6. If everything is installed correctly, the body will reboot into a white screen with the inscription "Fastboot" on top
7. We execute from the console "fastboot boot prestoroot.img"
8. The device will have to reboot, turn it off and turn it on again
9. Through the Android Market (Google Play) install "Superuser"
10. Everything, root is received.
11. To install Clockworkmod recovery, repeat steps 3 to 7.
12. Run “fastboot flash recovery recovery.img” from the console after the response is received that the recovery is flashed, give the command “fastboot reboot” - the body will reboot.
13. CWM is installed in order to get into it on the switched off phone, press "volume down" and without releasing turn on the device, after the Pantech logo appears, after a few seconds the standard menu cwm recovery will appear
Thanks for the instructionAlexeyT1980

Route and CWM for 4.0.4

Make sure you have the Java Development kit, Android SDK with the Android SDK Platform-tools installed, and Pantech PC Suite, which installs the USB driver.
The presence of a micro sd card is required.
Ruth
1. Download and unzipcwm-5.0.2.7-presto.img.zip(to the platform-tools folder)
2. DownloadSuperuser-3.0.7-efghi-signed.zip(archive to the same folder)
/ the path on my computer looks like this C: \ Users \ FinN \ AppData \ Local \ Android \ android-sdk
3. shift + RMB on the folder - platform-tools, then click open the command window.The phone must be fully loaded, USB debugging enabled.
4.adb push Superuser-3.0.7-efghi-signed.zip / sdcard / external_sd /
5. adb reboot bootloader
6.fastboot boot cwm-5.0.2.7-presto.img
7. The body will go into recovery, select choose zip from sd card
8. Choose Superuser-3.0.7-efghi-signed.zip, install
Note: You must install the zip several times until the symlink at the end of the installation works (that is, when the word error is not at the end).
9. Restart the phone.
Recovery (root is required)
Important: you can bounce the phone by incorrectly flashing MMS sections
Note: CWM is not required to be installed. You can backup and flash via fastboot boot (recovery.img)
The requirements above are relevant.
adb push cwm-5.0.2.7-presto.img / data / local / tmp /
adb shell
su
dd if = / data / local / tmp / cwm-5.0.2.7-presto.img of = / dev / block / mmcblk0p18
sync
exit

How to unlock a bootloader?

To do this, we need already installed root and CWM.
1. fillGBBoot.zipto an external flash drive
2. sew a zip from recovery
3. Reboot the phone, and get an unlocked bootloader.

how to flash CM10

link

Russifiers

for 2.3
For 4.0.4odexanddeodex(more complete).

Utility

Offline program for unlock ATT(Choose the model P9050)
If you do not have enough LED indicator
Dark versions of GAPPS(dark color has less charge, this is a feature of Amoled displays)
Ways to improve sound quality / volume
Dark theme for CM10

If Wi-Fi does not work on 4.x

WiFix-install, and follow the instructions of the program

HavetoRbutshbut

пїЅ download

elswithtatbut

Changed curtain and battery from InfusionNSK for deodex 4.0.4
Changed electrod battery for deodex 4.0.4
Shutter for 2.3 from InfusionNSK

Known Issues

Shell has been granted Superuser rights.
When you press the volume keys, debug mode is activated. It's okay.

Post has been editedOXALIS - 15.06.16, 23:12

Reason for editing: edited the title of the topic and the navigator

[priz]

In Fastboot mode, the computer does not see the phone ....

did as scheduled in the drivers
1) pantech pc suite - without it, the computer does not see the beast
2) less often you need to install PdaNet (Android firewood is sewn into the installation of this program)

Don’t install, says Suite is not installed .....


Throw off who the driver thread to install manually through the update .....

[repain]

priz,
connect the animal to the computer, let the suite put firewood. there’s no one on the phone and then put it on your computer. During installation will ask to disconnect
(during installation, select the other phone)

I also did not see the animal in the fastboot.
this method helped

and further. go to the dispatcher device and see if there are any incorrectly installed firewood, if any, delete and reinstall the suite and give

Post has been editedrepain - 21.09.12, 10:28

[priz]

[email protected], 10:26

repain

Can you unload the installed drivers ???, the suite is installed, everything works, but the problem remains ......

Post has been editedpriz - 21.09.12, 17:20

[Andreys19]

try the kids: [url = "http://rghost.ru/5096819"] approached me

[repain]

priz,
if I knew how to do this, I would unload it)

[priz]

Andreys19 @ 09.21.2012, 17:38

try this:

Thank!! Came up !!!!
Paste in a hathttp://rghost.ru/5096819come in handy)))

[email protected], 17:47

if I knew how to do this, I would unload it)

You can use Driver Genius or any similar program))

[Artpetrovich]

Comrades, where can I read in more detail about the Russification procedure? I bought this device, before that I did not use Android smarts. Android version 2.3.5. Thank you in advance.

[repain]

Artpetrovich,
To begin with, according to the instructions, we put the root and recovery
open it from the folder sohttp://otvety.google.com/otvety/thread?tid=2903a925200546d9

. Next, download the crack to a USB flash drive (not to the phone’s memory) and spill it into the recovery. like, this, too, seems to be in the instructions

[Artpetrovich]

Everything is super, it turned out to flash, the Russian language appeared. Just another problem arose - when changing the theme to one of the standard ones, the message "The Pantech Launcher application stopped unexpectedly (com.pantech.launcher process) has occurred. Try again." Does anyone know how to remove the infection?

[repain]

Artpetrovich,
Change launcher.
For example, on the same tachvis or on nemus

[Finn81]

Source from attn1
Make sure you have the Java Development kit, Android SDK with the Android SDK Platform-tools installed, and Pantech PC Suite, which installs the USB driver.
The presence of a micro sd card is required.
Ruth
1. Download and unziphttp://tau.shadowchild.nl/files/cwm-5.0.2.7-presto.img.zip(to the platform-tools folder)
2. Downloadhttp://tau.shadowchild.nl/files/Superuser-...fghi-signed.zip(archive to the same folder)
/ the path on my computer looks like this C: \ Users \ FinN \ AppData \ Local \ Android \ android-sdk
3. shift + RMB on the folder - platform-tools, open the command window. The phone must be fully loaded, USB debugging is enabled
4.adb push Superuser-3.0.7-efghi-signed.zip / sdcard / external_sd /
5. adb reboot bootloader
6.fastboot boot cwm-5.0.2.7-presto.img
7. The body will go into recovery, select choose zip from sd card
8. Choose Superuser-3.0.7-efghi-signed.zip, install

Note: You must install the zip several times until the symlink at the end of the installation works. (That is, when there is no word error at the end)
9. Restart the phone.

Recovery (root required)
Important: you can bounce the phone by incorrectly flashing MMS sections
Note: CWM is not required to be installed. You can backup and flash via fastboot boot (recovery.img)
The requirements above are relevant.
adb push cwm-5.0.2.7-presto.img / data / local / tmp /
adb shell
su
dd if = / data / local / tmp / cwm-5.0.2.7-presto.img of = / dev / block / mmcblk0p18
sync
exit
(I had to enter exit command 2 times)

/ edittyts
Backup 4.0 with root, you can sew from 2.3. The recovery does not crash.

Post has been editedFinn81 - 04.10.12, 22:13

[blackjack9999]

Finn81,


sat for about 40 minutes stuck ... everything turned out !!!! well-deserved

[Finn81]

Reloaded backup with 4share on google drive
https://docs.google.com/file/d/0B-Lqk5rmmhO...lNjYm9MN1U/edit

[repain]

Finn81,
Sorry, but what kind of backup is this?

[Finn81]

Post edited, see the end)

[repain]

Finn81,
If I pump it out of that recovery that costs by default (not CWM), a ride?
And as I understand it, all my installed applications will fly off?

[Finn81]

They will fly off. You can’t roll from the initial one, there is no backup / restore item there.
ps how is the download speed from google drive?

Post has been editedFinn81 - 05.10.12, 11:41

[Balavnic]

Bliiiiin, brothers, write who is the thread of the fact, you should do it to the native who exchanged this current-current cell phone for diamonds, but such an android wasn’t heard from a scumbag. Pliiiiiz !!! : sveta:

[repain]

Balavnic,
You can sell the phone. What do you want then? Question normally put

[repain]

Finn81,
Note: CWM is not required to be installed. You can backup and flash via fastboot boot (recovery.img)

I wanted to flash it, but where is the file itself? cwm-5.0.2.7-presto.img, is it?