UNDER CONSTRUCTION Last update - 07.10.2012 by UTerminatorU PIPO M1 is charged by USB?
[Color "red"]Not! [/ color]
If you turn tell everyone how :)
What are the characteristics of the charger?
5v - 2,5A
What materials are made by the body and the screen?
The housing, the rear cover is made of aluminum, with a pleasant tactile and texture, perimeter edging plastic screen - crystal, it is usually glued to transport two film.
Which cards support PIPO M1?
Up to 32GB, so someone used a larger amount has not yet heard.
Reads the card formatted likeFat and in NTFS .
Statistics:
16 Gb Genuine Kingston Memory Card AKSTF16G, Grade 4 - never fell off and hangs noticed jambs.
16 Gb Kodak, Grade 4 - were noticed problems.
32 Gb Transcend ultimate, Grade 10, NTFS - is falling off and once she is, does not bother to work does not interfere with recording speed of 3-6 Mb / s.
8 Gb Transcend, Grade 4 - were noticed problems.
16 Gb Transcend, 10th grade - was not noticed problems.
32 Gb AData, class 4 - runs like clockwork.
Information about the non-working cards (I have not personally tested)
Cards do not work in our unit (fall off after waking up)
32 Gb Silicon Power, Grade 10
32 Gb SanDisk,? class
4 Gb SanDisk,? class
8 Gb nokio (?), Class 6
8 Gb Samsung, Grade 6
More will complement.
What are the problems with memory cards?
According to statistics from time to time and not with all models of memory cards is spontaneous otvalivanie memory card,
after which it is usually located immediately itself. Especially live does not prevent, except for some (5-10 seconds) while the screen is turned on.
Yet there have been complaints that the card fell off after waking up (I specifically was not like this).
Are there problems with the touch screen, ghosting, jitter, "dead" zone?
Touch screen is excellent, responsiveness and sensitivity to the mark, there were no problems or complaints.
What performance benchmark results?
The average results:
Antutu benchmarkin the range 7600 - 8100;
Quadrantin the range of 4100 - 4300
How long does a fully charged battery?
From 2 to 5 hours at a maximum (!) Of the processor load, and depending on variations in brightness and on / off WIFI, EEPROM.
At the middle and low load is enough for a long time of 5-9 hours.
For more details, see the details. Battery test results Antutu tester
I have a battery to sit down very quickly from 100% to 80-90%, is this normal?
Yes, this is normal, especially for non-trained battery. According to statistics, nearly all sit down to 80-90% in the first 5-30 minutes, then almost linearly and at the end of 19% to a minimum of a little longer.
Antutu tester - the results of the battery test
What is the best test to Antutu tester?
Until you deal with PIPO M1 power completely, I will lay out for all to see reports of their experiments. By the way very much like, if it is real, do the subsection in the header "Power / Benchmarks" Due to the fact that the device is really cool, and the community has gathered sufficient for such experiments quantity offer those interested to take part in the test and clarify the nuances of the tablet consumption, at the same time to collect as much statistical data for comparison and analysis. So I suggest the following procedure:
1.
Antutu testerBy default all incl WIFI area, off bluetooth. Result spread in a number of points and time intervals:
- Firmware
- score
- Start xx: xx = 100%
- Part1 yy: yy = n%
- Part2 zz: zz = m%
- Finish qq: qq = k%
(Mask: time = remaining percentage)2.
Antutu tester, brightness at minimum, including WIFI area, off bluetooth. The brightness should be changed as soon as the start of the test, click on the bottom panel and manually unscrew at least Results in the same form.
3.
Antutu tester, brightness at 30% -50% (comfortable for watching movies, yet to be determined what the appropriate value for me at least is better to specify), including WIFI area, off bluetooth. Results in the same form.
4.
Battery monitor widgetnormally shows the voltage, not round. With the help of a program, it will be useful to mention the
Voltage 100%
Voltage at the end of the test, when the tablet is discharged.
Time such testing actually takes quite a lot (charge + discharge (2-5chasov)), so it is better to do it at night (0 tablet is not discharged, so you can not be afraid to leave it unattended discharge), then when there is a an opportunity not to use the tablet. I'm going to try every night to spread the results have not yet clarified.
My results: 1. Firmware stock + Root
result1 491
The gaps are not recorded, the test lasted 2:00 minutes 10-20
result2 472
The gaps are not recorded, the test lasted the same 2:00
2. Brightness min.
901 result
The gaps are not recorded, the test lasted 5:00
Voltage
3,9v = 100%
3,6v = 11%
Framed later, it would be even better to a separate branch
And what he has sensor? Lighting, gyroscope, compass, proximity, etc.?
Only gravity sensor.
How to disassemble the tablet? (Thanks volosatiy064)
How to enter the menu rekaveri / Safe Mode?
1. Log in to safe mode.
The tablet is turned off.
Pressed the power, then during boot vol- - safe mode
2. Log in rekaveri
The plate was again off
clamped vol-, then the power - entered the lying robot voskl mode. sign.
In this mode, pressing the power and vol + - entered rekaveri 4.1
The order of importance of clicks! just as it is written
Items 1 and 2 are not interconnected.
How does Skype?
Someone interested in how the Skype compared to "Bendova" devices. I take as the standard of samsung galaxy s gt-i9000.
So test tests conducted on the provider will (20-30 megabits + wifi router) within the apartment in a bundle
PC PIPO M1. As a result of my subjective assessment: Video - 4+ or 5, ie enough for quite comfortable
communication, even if not very good light, does not slow down, the sound 4 or 5, with included to enhance programmke
sound on your computer can be heard a slight background noise, the microphone on the tablet itself is quite, because hear the interlocutor well
fine. Overall I would give the plate more than 5 4+. Compared with Ainol Aurora II and Cube U30GT - it's solid 5!
How to get ROOT rights?
Windows 7 (32/64) + Windows XP (32/64) What do you need:
1). Incl. the tablet.
2). YUSB enable debug mode.
3). Connect to a computer.
3a). Depending on your installed
Windows 7 / XP 32bit or
Windows 7 / XP 64bit shake Installer Android ADB Interface Driver ->[Attachment = "2080183: PDAnet-32bit.zip"], [attachment = "2080188: PDAnet-64bit.zip"]. (If, suddenly difficult English. Instructions with pictures
here )
3b). If it is determined as an unknown device (I did so), download the attached file and install the drivers, choose "Android ADB Interface".
3c). If it is determined as the otherwise - to remove the driver, and see from the manager point 3a), 3b)..
4). Install the program ->[Attachment = "2080209: ZhuoDaSh .... 9-setup.exe"]
5). Next, follow the instructions ->[Attachment = "2080242: Pipo M1 root JB.doc"]
6). first reboot. The device is so slow.
7). Restart the second - all ok. I check the root-explorer - to write works.
Everything!
Drivers -
ADB-DriversThank krava33, for the initial instructions.
P.S. Part of the solution has helped the
fast.
How to reflash?
For English.
Firmware
Pipo Max M1 Jelly Bean TNT Release 2 Firmware Imageand
instructionlie
here.
Official firmware
20120913 - standing in a fresh supply of tablets, nothing is known about her, except that a "convenience store less trouble" (not verified), too, have not seen on the network, I do not set.
20120828 - has been forced to set, there is a problem with the market, changes in build.prop yielded nothing. Problems with the reception of files via bluetooth, no!
20120810 - I do not know anything, do not put.
20120806 - was originally on the tablet apps in the Market, after build.prop changes normally staged. There were problems with the reception via bluetooth files.
Who would find - a lighthouse in a personal, it would be good as much as possible to collect them. When it was a link to offsite, there were two of them now is offsite.
Custom firmware
The same, the more we collect - the better it will be plenty to choose from and something to compare with all the pluses and minuses. I will add only proven, either personally or with reviews.
I try to collect as much information together and made into something concrete :)
What is 3G modem can be connected?
3G tehn. Model Model Manufacturer Support Quality
----------------------------------------------------------
EVDO EC122 EC122 HUAWEI ****
EVDO EC1260 EC1260
EVDO EC1261 EC1261 HUAWEI ****
EVDO EC189 EC189
WCDMA E1750 E1750 HUAWEI **
WCDMA E261 E261 HUAWEI ***
WCDMA MF190 MF190 ZTE
---------------------------------------------------------
The tablet is not charging, what to do?
1). Check whether the green LED lights on the charger? If it is not lit, check whether the tester operating it at all.
2). Just found complete with charging, without LED, then immediately tester.
3). Many plug charger lacks and is not fixed in the socket plate. Corrected cutting of gum on the plug so that it sticks to the deeper 1-1,5 mm.
What parameters memory plug?
diameter of 2.5 mm
length 10mm
The internal diameter of 1mm.
Fully discharge PIPO M1, what to do?
To get involved PIPO try the following:
1). Behind rezet button press (of course first necessary to be sure that the tablet is charged). Incidentally surveillance off state if the charging plug the tablet turns on, that is only charged on.
2). If rezet not helped press and hold for a long time (15 seconds) button incl.
3). If does not work, press and hold the ON + gromk.menshe
4). If that fails, paragraph 3). after 2).
5). If does not help, just leave on charge as possible on longer and then see para. 1).
At me after trying different combinations of these actions are all-inclusive and Georgia. In fact, the description of the action rather muddled from not knowing for sure what combination they do.
I have a soft sound, what to do?
put free
SpeakerBoostfrom the market.
Set the gain to 100%
Check that no wheezing at max. volume (I did not wheeze). If there is a wheeze to reduce the volume gain.
Rejoice.
The plate is really hot?
About heating - it is not heated at all. More precisely, under stress the body back, getting a little warm, but apparently
aluminum back cover did not disdained to use a heat sink.
How does the WIFI?
Good! (Usually)
I have an application from the Market is not installed, what to do?
After the forced reinsertion of the drain in the sink 20120806 2120828, even after the change of build.prop identify rows in a convenience store in some applications (on the old firmware, everything was ok), writes "Your device is not compatible with this version", while in the search for solutions to all contributing will be very grateful to (+)!
Change in Market identification, to improve compatibility (taken from ymdim26 - thanks!)
First be sure to get the right ROOT!
ro.build.tags = release-keys
ro.product.model = GT-I9100
ro.product.brand = Samsung
ro.product.name = GT-I9100
ro.product.device = GT-I9100
ro.product.board = GT-I9100
ro.product.manufacturer = Samsung
ro.product.locale.language = en
ro.product.locale.region = RU
ro.build.version.incremental = XXLPQ
ro.board.platform = rk30xx
# ro.build.product is obsolete; use ro.product.device
ro.build.product = rk30sdk
# Do not try to parse ro.build.description or .fingerprint
ro.build.description = GT-I9100-user 4.0.3 IML74K XXLPQ release-keys
ro.build.fingerprint = samsung / GT-I9100 / GT-I9100: 4.0.3 / IML74K / XXLPQ: user / release-keys
ro.build.characteristics = tablet
Marked lines are responsible for the market, for a complete change of identity of the device is better to change all)
Because the file system, do not be lazy and do backups. Random error in this file can transform our PIPO in conventional "brick". Good luck to all)
P.S. From me, it is checked at the expense of bricks - did so :) + Future Council, a proven way build.prop change - Editor in Root Explorer, otherwise, if you make changes BB, for example, and then copied back to the replacement may occur with problems rights = brick / butlup. We'll have to alter.
Tweaks build.prop (only for root, at your own risk)
Next in theory should slightly reduce energy consumption.
wifi.supplicant_scan_interval = 180 - Increases the WIFI network scanning interval affect the network speed of detection. Value in seconds.
pm.sleep_mode = 1 - instruction that controls power, when we extinguish the device screen. More
here .
ro.ril.disable.power.collapse = 0 - in theory allows the phone to go into "deeper" sleep.
I have these three lines spelled out, the tablet is at least as welled up :). As far as it is something I will unsubscribe gives as few popolzuyutsya.
The good news - for the night tablet NEVER coming out of a dream!